Datasheet
MAX4581/MAX4582/MAX4583
Low-Voltage, CMOS Analog
Multiplexers/Switches
_______________________________________________________________________________________ 5
ELECTRICAL CHARACTERISTICS—Single +3V Supply
(V
CC
= 2.7V to 3.6V, V
EE
= 0V, V
_H
= 2.0V, V
_L
= 0.5V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at T
A
= +25°C.)
SWITCH DYNAMIC CHARACTERISTICS
C, E, A 400
T
A
= +25°C
Address Transition
Time
t
TRANS
ns
V
X_
, V
Y_
, V
Z_
= 1.5V/0V; R
L
= 300Ω;
C
L
= 35pF; Figure 2
130 300
C, E, A 300
T
A
= +25°C
Enable Turn-Off Time t
(OFF)
ns
V
X_
, V
Y_
, V
Z_
= 1.5V; R
L
= 300Ω;
C
L
= 35pF; Figure 3
50 200
C, E, A
T
A
= +25°C
-10 +10
Break-Before-Make Time
t
BBM
ns
C, E, A
V
X_
, V
Y_
, V
Z_
= 1.5V; R
L
= 300Ω; C
L
= 35pF 15 40
C, E, A
T
A
= +25°C
400
C, E, A
Logic Input Logic
Threshold High
V
AH
, V
BH
, V
CH
,
V
ENABLEH
V1.0 2.0
C, E, AInput-Current High
I
AH
, I
BH
, I
CH
,
I
ENABLEH
µAV
A
, V
B
, V
C
= V
Enable
= 2.0V
-100 +100
-1 +1
C, E, A
Logic Input Logic
Threshold Low
V
AL
, V
BL
, V
CL
,
V
ENABLEL
V0.5 1.0
T
A
= +25°C
Enable Turn-On Time t
(ON)
ns
V
X_
, V
Y_
, V
Z_
= 1.5V; R
L
= 300Ω;
C
L
= 35pF; Figure 3
170 300
C, E, A
C, E, AInput-Current Low
T
A
= +25°C
I
AL
, I
BL
, I
CL
,
I
ENABLEL
X, Y, Z Off-Leakage
(Note 6)
I
X(OFF)
,
I
Y(OFF)
,
I
Z(OFF)
nA
MAX4581
µA
V
CC
= 3.6V;
V
X_
, V
Y_
, V
Z_
= 1V, 3.0V;
V
X
, V
Y
, V
Z
= 3.0V, 1V
V
A
, V
B
, V
C
= V
Enable
= 0.5V
-100 +100
T
A
= +25°C
-2 +2
X, Y, Z On-Leakage
(Note 6)
I
X(ON)
,
I
Y(ON)
,
I
Z(ON)
nA
MAX4581
V
CC
= 3.6V;
V
X
, V
Y
, V
Z
= 3.0V, 1V
-2 +2
C, E, A
C, E, A
X_, Y_, Z_ Off-Leakage
(Note 5)
-50 +50
I
X_(OFF)
,
I
Y_(OFF)
,
I
Z_(OFF)
T
A
= +25°C
nA
V
CC
= 3.6V; V
X_
, V
Y_
, V
Z_
= 1V, 3V;
V
X
, V
Y
, V
Z
= 3V, 1V
Power-Supply Current I
CC
, I
EE
µA
-1 +1
T
A
= +25°C
-50 +50
T
A
= +25°C
-1 +1
Switch On-Resistance
-1 +1
-1 +1
V
CC
= 3.6V,
V
A
, V
B
, V
C
, V
Enable
= V+ or 0V
-1 +1
-10 +10
PARAMETER
R
ON
T
A
= +25°C
SYMBOL TEMP
Ω
V
CC
= 2.7V; I
X
, I
Y
, I
Z
= 0.1mA;
V
X
, V
Y
, V
Z
= 1.5V
190 450
C, E, A
550C, E, A
UNITS
MIN TYP MAX
(Note 2)
CONDITIONS
Analog-Signal Range
V
X_
, V
Y_
, V
Z_
,
V
X
, V
Y
, V
Z
VV
EE
V
CC
C, E, A
MAX4582
MAX4583
MAX4582
MAX4583
Note 2: The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 3: ∆R
ON
= R
ON(MAX)
- R
ON(MIN)
.
Note 4: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified
analog signal ranges; i.e., V
X_
, V
Y_
, V
Z_
= 3V to 0 and 0 to -3V.
Note 5: Leakage parameters are 100% tested at maximum-rated hot operating temperature, and guaranteed by correlation at T
A
= +25°C.
Note 6: Guaranteed by design, not production tested.
ANALOG SWITCH
DIGITAL I/O
SWITCH DYNAMIC CHARACTERISTICS
(Note 6)
POWER SUPPLY