Datasheet

MAX4516/MAX4517
Dual-Supply, Low-On-Resistance,
SPST, CMOS Analog Switches
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—±5V Supply
(V+ = +4.5V to +5.5V, V- = -4.5V to -5.5V, V
INH
= 3.5V, V
INL
= 1.5V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are
at T
A
= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(Voltages Referenced to V-)
V+..............................................................................-0.3V, +13V
Voltage into Any Terminal (Note 1)
or ±20mA (whichever occurs first) ..........-0.3V to (V+ + 0.3V)
Continuous Current into Any Terminal..............................±20mA
Peak Current, NO, NC, or COM_
(pulsed at 1ms, 10% duty cycle)..................................±30mA
ESD per Method 3015.7 ..................................................>2000V
Continuous Power Dissipation (T
A
= +70°C)
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
5-Pin SOT23-5 (derate 7.1mW/°C above +70°C) ........571mW
8-Pin CERDIP (derate 8.00mW/°C above +70°C)........640mW
Operating Temperature Ranges
MAX4516C_ _/MAX4517_ _................................0°C to +70°C
MAX4516E_ _/MAX4517E_ _...........................-40°C to +85°C
MAX4516MJA/MAX4517MJA ........................-55°C to +125°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec).............................+300°C
Note 1: Voltages exceeding V+ or V- on any signal terminal are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
V+ = 5V, V- = -5V,
V
NO
or V
NC
= 3V,
I
COM
= 1mA
Ω
25
R
ON
10 20
M
COM to NO or NC
On-Resistance
V+ = 5.5V, V- = 5.5V,
V
COM
= ±4.5V,
V
NO
or V
NC
= 4.5V
±
nAC, E
-100 100
I
NO(OFF)
I
NC(OFF)
NO or NC Off-Leakage
Current (Note 3)
CONDITIONS
M
-20 20
T
A
= +25°C
V+ = 5.5V, V- = -5.5V,
V
COM
= ±4.5V,
V
NO
or V
NC
= 4.5V
±
-1 0.01 1
nA
T
A
= T
MIN
to T
MAX
C, E
V
IN
= V+, 0V
-100 100
µA-0.5 0.03 0.5I
IH
, I
IL
Input Current Logic
High or Low
COM Off-Leakage Current
(Note 3)
-20 20
T
A
= +25°C -1 0.01 1
T
A
= T
MIN
to T
MAX
I
COM(OFF)
M
V+ = 5.5V, V- = -5.5V,
V
COM
= ±4.5V,
V
NO
or V
NC
= ±4.5V
nAC, E
-200 200
COM On-Leakage Current
(Note 3)
-40 40
T
A
= +25°C -2 0.01 2
T
A
= T
MIN
to T
MAX
I
COM(ON)
VV- V+ - 3.5VV
IL
VV+ - 1.5V V+V
IH
Input Logic High
Input Logic Low
T
A
= T
MIN
to T
MAX
T
A
= +25°C
24T
A
= +25°C
VV- V+
V
COM
, V
NO
,
V
NC
Analog Signal Range
UNITS
MIN TYP MAX
(Note 2)
SYMBOLPARAMETER
Ω
6
R
FLAT(ON)
COM to NO or NC
On-Resistance Flatness
T
A
= T
MIN
to T
MAX
ANALOG SWITCH
DIGITAL I/O
V+ = 5V, V- = -5V;
V
NO
or V
NC
= 3V, 0V, -3V;
I
COM
= 1mA