Datasheet

MAX366/MAX367
Signal-Line Circuit Protectors
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V+ = +15V, V- = -15V, T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1: Guaranteed, but not tested.
Note 2: See
Typical Operating Characteristics curves for fault-free analog signal range at various supply voltages.
V+ to V-......................................................................-0.3V, +44V
IN_, OUT_..................................................(V- + 44V), (V+ - 44V)
Continuous Current into Any Terminal..............................±30mA
Peak Current into Any Terminal
(pulsed at 1ms, 10% duty cycle)...................................±70mA
Continuous Power Dissipation (T
A
= +70°C)
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ....727mW
8-Pin SO (derate 5.88mW/°C above +70°C).................471mW
8-Pin CERDIP (derate 8.00mW/°C above +70°C).........640mW
18-Pin Plastic DIP (derate 11.11mW/°C above +70°C) ...889mW
18-Pin Wide SO (derate 9.52mW/°C above +70°C) .....762mW
18-Pin CERDIP (derate 10.53mW/°C above +70°C).....842mW
Operating Temperature Ranges
MAX36_C_ _ ........................................................0°C to +70°C
MAX36_E_ _......................................................-40°C to +85°C
MAX36_M_ _...................................................-55°C to +125°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec).............................+300°C
V+ = V- = 0V, V
OUT
= 0V,
V
IN
= ±35V
V+ = 15V, V- = -15V (Note 2)
(Note 1)
V+ = 10V, V- = -10V, V
IN
= ±5V,
I
OUT
= 1mA
V
IN
= ±10V, I
OUT
= 1mA
V
IN
= V+ or V-,
100kΩ < R
OUT
< 1000MΩ (Note 1)
V+ = 15V, V- = -15V, V
IN
= ±10V,
I
OUT
= 1mA
V+ = 5V, V- = -5V, V
IN
= ±2V,
I
OUT
= 1mA
CONDITIONS
nA
-10 10
I
IN(OFF)
Signal-Path Leakage
(with Overvoltage)
Ω
10
∆R
(IN-OUT)
Signal-Path Resistance Match
7
Ω
400
R
(IN-OUT)
Analog-Signal-Path Resistance
V-11 11V
IN
, V
OUT
V(V+ - 40) (V- + 40)V
IN
, V
OUT
Analog Signal Range
Fault-Free Analog Signal Range
140 350
150
125
62 100
V(V- + 3) (V+ - 1.5)V
OUT
Analog-Signal Output
Range (Fault)
62 85
100
125
UNITSMIN TYP MAXSYMBOLPARAMETER
+25°C
All
All
+25°C
M
C, E, M
C, E
+25°C
All
+25°C
C, E
+25°C
M
C, E, M
TEMP.
RANGE
V+ = V- = 0V, V
IN
= ±35V,
V
OUT
= open circuit
nA
-1000 1000
I
IN(OFF)
Signal-Path Leakage
(Power Off)
-10 10
C, E, M
+25°C
V
IN
= ±25V, V
OUT
= open circuit nA
-1000 1000
I
IN(ON)
Signal-Path Leakage
(with Fault Condition)
-10 10
C, E, M
+25°C
V
IN
= V
OUT
= ±10V nA
-100 100
I
OUT(ON)
Signal-Path Leakage
(without Fault Condition)
-1 1
C, E, M
+25°C
-1 1+25°C
R
(IN-OUT)
< 1000Ω (Note 2) V±2.25 ±18V+, V-
Power-Supply Range
(without Fault Condition)
+25°C,
C, E, M
µA
-10 10
I+, I-Power-Supply Current
C, E, M
V0 ±18V+, V-Power-Supply Range
+25°C,
C, E, M
C, E, M -1000 1000
POWER SUPPLY