Datasheet

(V+ = +12V, V- = 0V, GND = 0V, V
AH
= +2.4V, V
AL
= +0.8V, T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
Note 2: The algebraic convention where the most negative value is a minimum and the most positive value a maximum is used in
this data sheet.
Note 3: Guaranteed by design.
Note 4: ∆R
ON
= R
ON(MAX)
- R
ON(MIN)
.
Note 5: Leakage parameters are 100% tested at the maximum rated hot temperature and guaranteed by correlation at T
A
= +25°C.
Note 6: Worst-case isolation is on channel 4 because of its proximity to the drain pin. Off isolation = 20log V
COM
/V
NO
, where V
COM
= output and V
NO
= input to off switch.
(T
A
= +25°C, unless otherwise noted.)
PARAMETER SYMBOL CONDITIONS
MIN TYP MAX
UNITS
(Note 2)
SWITCH
Analog Signal Range V
NO
, V
COM
(Note 3) 0 12 V
On-Resistance R
ON
I
NO
= 0.2mA, V
COM
= 3V or 10V, T
A
= +25°C 460 700 Ω
DYNAMIC
Transition Time (Note 3) t
TRANS
V
NO_
= ±5V, V
IN
= 2.4V, Figure 1, T
A
= +25°C 350 600 ns
Enable Turn-On Time
(Note 3)
t
ON(EN)
V
INH
= 2.4V, V
INL
= 0V, V
NO1
= 5V, Figure 3,
T
A
= +25°C
350 600 ns
Enable Turn-Off Time
(Note 3)
t
OFF(EN)
V
INH
= 2.4V, V
INL
= 0V, V
NO1
= 5V, Figure 3,
T
A
= +25°C
110 500 ns
Charge Injection
(Note 3)
Q C
L
= 100pF, V
NO
= 0V, R
S
= 0Ω, T
A
= +25°C 5.0 10 pC
100
0.001
10 10k1k100 100k
TOTAL HARMONIC DISTORTION
vs. FREQUENCY
0.01
MAX336/337 TOC02
FREQUENCY (Hz)
THD (%)
1
0.1
10
V+ = +15V
V- = -15V
SIGNAL = 5Vp-p
600Ω IN AND OUT
100
10
1
0.1
0.01
0.0001
0.001
0.00001
MAX336/MAX337 TOC-03a
V
IN
(V)
30 6 9 12 15
SUPPLY CURRENT
vs. INPUT VOLTAGE
I+ (µA)
CURRENT SHOWN IS FOR DRIVING
ONE INPUT; TOTAL V+ CURRENT IS
MULTIPLIED BY NUMBER OF LOGIC
INPUTS DRIVEN
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
0.1 10 100
FREQUENCY RESPONSE
225
-225
-90
-45
0
45
-135
-180
90
135
180
MAX1336/337toc01
FREQUENCY (MHz)
LOSS (dB)
PHASE (DEGREES)
1
50Ω IN AND OUT
V+ = +15V
V- = -15V
ON PHASE
OFF LOSS
ON LOSS
MAX336/MAX337 16-Channel/Dual 8-Channel,
Low-Leakage, CMOS Analog Multiplexers
www.maximintegrated.com
Maxim Integrated │ 4
Electrical Characteristics—Single Supply
Typical Operating Characteristics