OWNERS MANUAL MODE D’EMPLOI PROFESSIONAL PA AMPLIFIER MAX 7136
MAX 7136 Professional PA amplifier Many thanks for purchasing this Maxgear product. Always read the safety instructions below before letting a professional install this equipment. GENERAL SAFETY INSTRUCTIONS - Always read the user guide before using the equipment. Keep the user guide in a place where everyone can read it. Use the equipment indoors and not in a humid rooms. Never remove or insert a plug from or into a wall socket with wet hands.
MAX 7136 Professional PA amplifier INSTALLATION Connection to the main supply Before connecting the amplifier to the mains socket, always make sure that: - The electric system and mains socket have an adequate grounding, compatible wi th the safety norms (if you are uncertain, consult specialized personal) - The mains voltage corresponds to that shown on the rear of the unit ( an allowance of up +/-10% is accepted) . - The power cord is not damaged and has no bare wires.
MAX 7136 Professional PA amplifier INSTALLATION Preventing or identifying interference First of all, check that the amplifier is installed in a place free from industrial of RF (radio frequency) interference. Avoid installing your equipment very near radio or TV sets, mobile phones, etc., as these can cause noisy interference.
MAX 7136 Professional PA amplifier 3 CONTROLS MAX 7136 10 0 W R M S /8 OHM PER CHA N N EL P E A K O U T P U T V O LT A G E : 2 8 V O LT S F us e :3 .5 A W A R N IN G A C:2 3 0 V 1. Inputs *. F O R C O N T IN U E D P R O T E C T IO N A G A IN S T R IS K O F F IR E R E P L A C E O N L Y W IT H S A M E T Y P E A N D R A T IN G O F F U S E *. T H E U N IT IS F O R IN D O O R U S E O N L Y *. T H E U N IT M U S T B E E A R T H E D *.
MAX 7136 Professional PA amplifier CONNECTORS The following diagrams show the wiring of the connectors that can be used wi th the amplifiers. To connect the amplifier to the loudspeaker enclosures always use power cables (speaker cables made up of two wires, normally with a large cross-section) .Take care of your connector cables, always gripping them by the plugs, avoid pulling them directly and winding them without knots or bends: they will last longer and be more reliable, which is to your advantage.
MAX 7136 Professional PA amplifier Nous vous remercions d’avoir choisi Maxgear. Lisez toujours les consignes de sécurité ci-dessous avant de faire installer cet équipement par un professionnel. CONSIGNES GÉNÉRALES DE SÉCURITÉ - Toujours lire le manuel de l’utilisateur avant d’utiliser l’équipement. Conserver le manuel de l’utilisateur dans un endroit accessible à tous. Utiliser l’équipement à l’intérieur et pas dans des pièces humides. Ne jamais brancher ou débrancher une prise avec les mains mouillées.
MAX 7136 Professional PA amplifier INSTALLATION Branchement au réseau électrique Avant de brancher l’amplificateur à la prise murale, toujours vérifier que : - le système électrique et la prise murale sont équipés d’une mise à la terre adéquate et sont compatibles aux normes de sécurité (si vous avez un doute, contactez un technicien expérimenté). - la tension du réseau correspond à la tension indiquée sur l’arrière de l’unité (avec tolérance de +/-10%).
MAX 7136 Professional PA amplifier INSTALLATION Prévention ou identification des interférences Tout d’abord, vérifiez si l’amplificateur n’est pas installé à l’endroit exposé aux interférences industrielles RF (de radiofréquences). Évitez d’installer l’appareil à proximité des récepteurs radio ou des téléviseurs, etc., car ces appareils peuvent provoquer des interférences bruyantes.
MAX 7136 Professional PA amplifier 3 Éléments de commande MAX 7136 10 0 W R M S /8 OHM PER CHA N N EL P E A K O U T P U T V O LT A G E : 2 8 V O LT S F us e :3 .5 A W A R N IN G A C:2 3 0 V *. F O R C O N T IN U E D P R O T E C T IO N A G A IN S T R IS K O F F IR E R E P L A C E O N L Y W IT H S A M E T Y P E A N D R A T IN G O F F U S E *. T H E U N IT IS F O R IN D O O R U S E O N L Y *. T H E U N IT M U S T B E E A R T H E D *. F O R P R O F E S S IO N A L U S E O N L Y L in k L in k 1.
MAX 7136 Professional PA amplifier Connecteurs Les diagrammes suivants représentent le câblage des connecteurs utilisables pour les amplificateurs. Pour le branchement de l’amplificateur à haut-parleur, utilisez toujours des câbles de puissance (câbles de haut-parleurs se composant de deux fils, en général à grande section).