GE T TING STARTED QUICK REFERENCE GUIDE M ARVEL UNDERCOUNTER REFRIGERATION MLBV024-SS01A MLBV024-SG01B M LW C 0 2 4 - S G 0 1 A T H E O R I G I N A L R E F R I G E R AT I O N E X P E R T S S I N C E 1 8 9 2
CONTENTS Contents: Important Safety Instructions Safety information ...............................................................2 Unpacking your appliance ................................................. 3 Installing your appliance ......................................................4 Electrical ..............................................................................5 Cutout and product dimensions ..........................................6 Door adjustments ....................................
UNPACKING YOUR APPLIANCE ! Warranty Registration WARNING It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at www.marvelrefrigeration.com. EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Failure to do so can result in personal injury. The following information will be required when registering your appliance.
INSTALLING YOUR APPLIANCE Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To ensure your product performs to specifications, the recommended installation location temperature range is from 50 to 100°F (10 to 38°C). Cabinet Clearance Ventilation is required from the bottom front of the appliance. Keep this area open and clear of any obstructions.
ELECTRICAL Electrical Connection A grounded 115 volt, 15 amp dedicated circuit is required. This product is factory equipped with a power supply cord that has a three-pronged, grounded plug. It must be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see Figure 6). If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to provide the proper power supply.
CUTOUT & PRODUCT DIMENSIONS 23 15⁄16” (608 mm) PREPARE SITE ! CAUTION Your product has been designed for either free-standing or built-in installation. When built-in, your unit does not require additional air space for top, sides, or rear. However, the front grille must NOT be obstructed, and clearance is required for an electrical connection in the rear.
16-1/2" 16-1/2" 90° Door Swing 90° Door Swing DOOR ADJUSTMENTS Stainless Steel Black, White and Wood Overlay 2175R(F) & 2275WC Models Grille Installation REMOVING AND INSTALLING GRILLE ! Door Wall Swing Wall 1/4" Min. (6 mm) 2-1/8" Min. (54 mm) WARNING WARNING - Disconnect electric power to the unit before removing the grille. When using the unit, the grille must be installed.
DOOR REVERSAL Reversing the Door Remove and reinstall bottom hinge: Location of the unit may make it desirable to mount the door on the opposite side of the cabinet. 1. Remove bottom hinge from cabinet by removing three screws. The hinge hardware will be removed and reinstalled on the opposite side of the cabinet. Figure 15 Figure 13 2. Remove corresponding screws on opposite side of cabinet. 3. Flip hinge plate over and reinstall on opposite side. Prepare door for reinstallation: 1. Remove gasket.
INSTALLING THE ANTI TIP DEVICE Anti-Tip Bracket NOTE 1. Slide unit out so screws on top of unit are easily accessible. If the room floor is higher than the floor in the cutout opening, adjust the rear legs to achieve a total unit rear height of 1⁄8” (3 mm) less than opening’s rear height. Shorten the unit height in the front by adjusting the front legs. This allows the unit to be gently tipped into the opening. Readjust the front legs to level the unit after it is correctly positioned in the opening. 2.
AIRLOW AND PRODUCT LOADING AIRFLOW NOTE External • Do not block the front grille - no additional clearance around sides, top or rear of unit is needed for ventilation • Do not install behind a closed door Restricting airflow may result in poor product performance, product failure, and uneven internal temperatures and may freeze contents.
INTERIOR ADJUSTMENTS INTERIOR SHELVES (MLBV024) Removing and Installing Interior Shelves 3 1 2 Figure 27 For models equipped with glass shelves having recessed shelf supports, remove the shelves as follows: 1. Pull shelf out about 6” (1), until back of shelf clears the “hump” on the right-hand side. 2. Tilt up right-hand edge of shelf (2). 3. Remove shelf from unit by pulling out (3). Insert the shelves as follows: 1.
INTERIOR ADJUSTMENTS Recommended Wine Storage (MLWC024) NOTE Wine bottles can be stored on the racks or bottom as shown. The racks are secured to the unit and are not designed to be removed. For your convenience, they are designed to pull forward approximately three inches. Bottom The bottom shelf of the unit is designed to hold up to six standard-size wine bottles.
USING YOUR ELECTRONIC CONTROL Control Function Guide Function Command Notes ON/OFF Press Unit will immediately turn ON or OFF. Leave Interior Light On Press and release to leave interior light on for 3 hours; press again to deactivate. After 12 hours, factory default is restored; light will turn on when door is open. Adjust Temperature Press or and release. When the display is flashing, press or to adjust the set point temperature.
CARE & CLEANING Cleaning Condenser Extended Non-Use INTERVAL - EVERY SIX MONTHS VACATION/HOLIDAY, PROLONGED SHUTDOWN To maintain operational efficiency, keep the front grille free of dust and lint, and clean the condenser when necessary. Depending on environmental conditions, more or less frequent cleaning may be necessary. The following steps are recommended for periods of extended non-use: 1. Remove all consumable content from the unit. 2.
Installation Operation and Maintenance Instructions OBTAINING SERVICE If Service is Required: • If the product is within the first year warranty period please contact your dealer or call Marvel Customer Service at 616.754.5601 for directions on how to obtain warranty 800.223.3900 coverage in your area. • If the product is outside the first year warranty period, Marvel Customer Service can provide recommendations of service centers in your area.
HOUSEHOLD PRODUCT WARRANTY Marvel Refrigeration (Marvel) Limited Warranty ONE YEAR LIMITED PARTS & LABOR WARRANTY For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.
www.marvelrefrigeration.com Marvel Refrigeration 1260 E. Van Deinse St. Greenville MI 48838 616.754.5601 30667 Rev A 2/25/21 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
