Installation Operation and Maintenance Instructions Ice Machine MA15CRS1XS
Installation Operation and Maintenance Instructions Contents Service Intro Troubleshooting Warranty Safety Obtaining Service Safety and Warning Disposal and Recycling Installation Environmental Requirements Electrical Cutout Dimensions Product Dimensions Side by Side Installation Water Hookup General Installation Grille Installation Door Swing Door Adjust Operating Instructions First Use Ice Airflow and Product Loading Maintenance Cleaning Cleaning Condenser Extended Non-Use 2
Installation Operation and Maintenance Instructions Welcome to the Marvel Experience Congratulations on adding a new Marvel crescent ice maker to your home and thank you for choosing our quality American-built product. You’ll enjoy years of crescent ice in the comfort and convenience of your home, backed by our full worry-free warranty. We are thrilled to welcome you to our growing community of Marvel owners, who trust in our products and our support.
Installation Operation and Maintenance Instructions Safety and Warning Disposal and Recycling ! DANGER NOTICE Please read all instructions before installing, operating, or RISK OF CHILD ENTRAPMENT. Before you throw away servicing the appliance. your old refrigerator or freezer, take off the doors and leave shelves in place so children may not easily climb inside.
Installation Operation and Maintenance Instructions Cutout Dimensions Electrical PREPARE SITE ! WARNING Your U-Line product has been designed for either freestanding or built-in installation. When built-in, your unit does SHOCK HAZARD — Electrical Grounding Required. Never not require additional air space for top, sides, or rear. attempt to repair or perform maintenance on the unit until However, the front grille must NOT be obstructed, and the electricity has been disconnected.
Installation Operation and Maintenance Instructions Product Dimensions Not Including Handle *Add 3/4" To Depth For Water Line Clearance 6
Installation Operation and Maintenance Instructions Side-by-Side Installation 3. Place bracket over holes and attach to unit with two screws removed in step 2 using a T-25 Torx driver. Tighten screws Two units may be installed side-by-side. fully. Cutout width for a side-by-side installation is the cutout 4. Gently push units into position. Be careful not to entangle dimension of a single unit times two. the electrical cord or water line, if applicable. No trim kit is required.
Installation Operation and Maintenance Instructions Water Hookup ! CAUTION PREPARE PLUMBING Do not use any plastic water supply line. The line is under The water valve uses a standard 1/4" (6.35 mm) compression pressure at all times. Plastic may crack or rupture with age fitting. and cause damage to your home. ! CAUTION Do not use tape or joint compound when attaching a braided flexible water supply line that includes a rubber gasket.
Installation Operation and Maintenance Instructions Anti-Tip Bracket 3. Locate water valve inlet. 1. Slide unit out so screws on top of unit are easily accessible. 2. Remove the two screws from the opposite side of the hinge assembly using a T-25 Torx driver (see below). 4. Break away filler feature in bushing with flat screwdriver. Remove ZLWK ɠDW screwdriver 5. Thread water line through back panel hole (with bushing). 3.
Installation Operation and Maintenance Instructions General Installation INSTALLATION 1. Plug in the power/electrical cord. LEVELING INFORMATION 1. Use a level to confirm 2. Gently push the unit into position. Be careful not to entangle the unit is level. Level the cord or water and drain lines. should be placed along top edge and side edge as shown. 3. Re-check the leveling, from front to back and side to side. Make any necessary adjustments.
Installation Operation and Maintenance Instructions Door Swing Grille Installation REMOVING AND INSTALLING GRILLE Wall 1/4" Min. (6 mm) ! WARNING Wall 2-1/8" Min. (54 mm) Disconnect electric power to the unit before removing the grille. When using the unit, the grille must be installed. Removing the grille 1. Disconnect power to the unit. 90° Door Swing 90° Door Swing 2. Loosen the two screws (1). 3. Remove grille (2) from unit.
Installation Operation and Maintenance Instructions Door Adjust Location of the unit may make it desirable to mount the door on the opposite side of the cabinet. HINGE COVER Hinge cover included with the literature bag is optional. The hinge hardware will be removed and reinstalled on the opposite side of the cabinet. To install hinge cover: TO REVERSE THE DOOR (Black and Stainless Models) 1. Press hinge cover squarely over hinge.
Installation Operation and Maintenance Instructions Install top hinge and door: 1. Install the top hinge. Do not tighten. 5. Remove door by tilting forward and lifting door off bottom hinge. Retain shoulder washers; they will be reused. 2. Rotate the door 180o to reverse and set the door onto the bottom hinge. 6. Remove three screws from hinge holes on the opposite side. Reinstall into holes where the hinge was removed. Take care not to scratch the cabinet. 3.
Installation Operation and Maintenance Instructions First Use To turn off ice production: Raise the bin arm into an All controls are preset at the factory. Initial startup for ice storage. upright and locked position. The unit will preserve temperature requires no adjustments. NOTICE NOTICE If not intending to use the ice maker, turn the water supply AGA Marvel recommends discarding the ice produced valve off.
Installation Operation and Maintenance Instructions ICE MAKER ADJUSTMENT 4. Install the ice maker assembly cover. Ice Cube Thickness Adjustment Interval - As Required ADJUSTING ICE HARVEST On ice maker equipped models, adjust the cube size by 1. Remove the front grille (see GRILLE INSTALLATION). changing water amount injected into the ice maker assembly as follows: 2.
Installation Operation and Maintenance Instructions Cleaning If any surface discoloring or rusting appears, clean it quickly EXTERIOR CLEANING nonabrasive cloth. Always clean with the grain. Always finish Vinyl Clad (Black or White) Models with Claire® Stainless Steel Polish and Cleaner or with Bon-Ami® or Barkeepers Friend Cleanser® and a comparable product to prevent further problems. Clean surfaces with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners.
Installation Operation and Maintenance Instructions DEFROSTING NOTICE Manual Defrost Models DO NOT clean ice bucket using a dishwasher. The bucket This unit is a manual defrost model and will require occasional defrosting. When there is build-up of 1/4" is not dishwasher safe and will be damaged. (6 mm) or more of frost, manually defrost the unit. 10.When the interior is dry, reconnect power and turn unit on.
Installation Operation and Maintenance Instructions Extended Non-Use VACATION/HOLIDAY, PROLONGED SHUTDOWN For questions regarding extended non-use, please The following steps are recommended for periods of call AGA Marvel at 800.223.3900. extended non-use or if the unit will be exposed to temperatures of 40°F (5°C) or less: ! CAUTION 1. Remove all consumable content from the unit. Damage caused by freezing temperatures is not covered by the warranty. 2.
Installation Operation and Maintenance Instructions Troubleshooting BEFORE CALLING FOR SERVICE TROUBLESHOOTING GUIDE If you think your AGA Marvel product is malfunctioning, read ! DANGER the CONTROL OPERATION section to clearly understand the function of the control. ELECTROCUTION HAZARD. Never attempt to repair or perform maintenance on the unit before disconnecting If the problem persists, read the NORMAL OPERATING the main electrical power.
Installation Operation and Maintenance Instructions Entire Product Limited One Year Parts and Labor Warranty AGA MARVEL warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
Installation Operation and Maintenance Instructions If Service is Required: • If the product is within the first year warranty period please contact your dealer or call AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, AGA MARVEL Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www.agamarvel.
www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.
