Operation Manual

ManualsBrandsMarantz ManualsAmplifierPM7002

ENGLISH

4 VIDEO SETUP

Video settings are made as follows.

Select “4. VIDEO SETUP” from the MAIN

MENU with the 3/4 cursor buttons and press

the OK/ENTER button.

4.VIDEO SETUP

VIDEO CONVERT

AUTO :DISABLE

OSD INFO :ENABLE

I/P CONVERT :ENABLE

HDMI OUT :OUTPUT1

COMPO OUT2 :MAIN

RETURN NEXT EXIT

Select the desired menu with the 3/4 cursor

buttons and press the OK/ENTER button.

•

VIDEO CONVERT

“4-1 VIDEO CONVERT”

•

TV-AUTO

Select the TV AUTO ON/OFF function to enable

or disable with the 1 or 2 cursor buttons. (refer to

page 66)

•

OSD INFO

Select the OSD information function to “ENABLE”

or “DISABLE” with the 1 or 2 cursor buttons.

If you select “ENABLE”, this unit will display the

status of the feature (Volume up/down, input

select, etc..) on the monitor. If you do not desire

this information, select “DISABLE”.

Note:

• OSD information is not output to Monitor Output

of HDMI and Component Video. However, OSD

information is output if the Video Convert function

is used to output Video or S-Video video signals to

Monitor Out of HDMI and Component Video.

For details, refer to“VIDEO CONVERT”on page 59.

•

IP CONVERT

Select the IP CONVERT ON/OFF function to

enable or disable with the 1 or 2 cursor buttons.

(refer to page 59)

•

HDMI OUT

This setting is for selecting which output terminal,

HDMI 1 or HDMI 2, to output the signal to. Select

the output destination with the 1 / 2 cursor

buttons.

To use the remote controller (RC8001SR) to

change the HDMI OUT setting, press the AMP

button and then the > button until the second page

is displayed. After HDMI 1 or HDMI 2 is displayed

on the remote controller, press the D3 or D4 button

to switch between them.

AMP

AUX2

AUX1

TAPE

TUNER

CD-R

LIGHT

Learning Remote Controller

RC8001SR

AMP

VOL

USE

PAGE

•

COMPONENT OUT 2

(This feature is not available on the SR7002.)

This setting is for selecting whether to output

the images for the main room or the images for

the multi room system to the COMPONENT

MONITOR OUT 2 terminal. Select the output

destination between MAIN and MULTI with the 1 /

2 cursor buttons.

Note:

• When MULTI is selected, video signals converted

from the MONITOR OUT 2 terminal are not

output.

After you complete this portion of the setup, move

cursor to “RETURN” with the 3, 4, 1 and 2 cursor

buttons and press the OK/

ENTER

button.

4-1 VIDEO CONVERT

This unit is equipped to convert video signals for

monitor output.

This section explains how to set up conversion for

each type of video input.

Select “4. VIDEO SETUP” from the MAIN

MENU with the 3 / 4 cursor buttons and press

the OK/ENTER button.

Select “VIDEO CONVERT” with the 3 / 4 cursor

buttons and press the OK/ENTER button.

VIDEO CONVERT

TV : ANA&HDMI

DVD : ANA&HDMI

VCR1 : ANA&HDMI

DSS : ANA&HDMI

AUX1 : ANA&HDMI

TAPE : ANA&HDMI

CD/R : ANA&HDMI

AUX2 : ANA&HDMI

RETURN BACK EXIT

Select “FUNCTION” with the 3 / 4 cursor

buttons and set the video conversion mode

with the 1 / 2 cursor buttons

ANA&HDMI:

This mode both up-converts and down-converts

analog video signals (Composite Video, S-Video,

Component Video). Furthermore, it up-converts

from analog video signal to HDMI. (It cannot down-

convert from HDMI digital video signals to analog

video signals.)

ANA ONLY:

This mode both up-converts and down-converts

analog video signals (Composite Video, S-Video,

Component Video). It does not up-convert to

HDMI.

OFF:

This mode turns off all conversion features.

Note:

• For details on video convert feature, see page 59.

SR7002-8002_U_01_ENG 2_3.indd 53SR7002-8002_U_01_ENG 2_3.indd 53 07.8.24 1:15:26 PM07.8.24 1:15:26 PM