Operation Manual
7
ENGLISH
REAR PANEL
NAMES AND FUNCTIONS OF PARTS
A PHONO Input jacks
These jacks are for connecting to an analog record player.
MM cartridges can be used.
B PHONO GND terminal
Connect the grounding wire from an analog record player.
C PRE OUT jacks
These jacks are for connecting to the input jacks of an-
other main-amplifier or active subwoofer.
D MAIN IN jacks
These jacks are for connecting to the output terminals of
another pre-amplifier when using the PM7001 as the main-
amplifier. In this case, set the SEPARATE switch H to the
ON position.
E SPEAKERS SYSTEM 1, 2 output terminals
You can connect 2 speaker systems, SPEAKERS 1 and
SPEAKERS 2 E. Speaker output can be turned ON/OFF
from the SPEAKERS 1 and 2 buttons o on the front panel.
F AC IN socket
Connect the supplied AC power cable to this socket and a
power outlet.
G REMOTE CONTROL jacks
These jacks are for connecting to other Marantz
components such as a CD player or DVD player that has a
remote control connector (D.BUS jack).
You can use the remote controller supplied with the PM7001
to control the system.
For more details, see page 13.
MODEL NO. PM7001
LL
SYSTEM 1 OR SYSTEM 2 4SYSTEM 1 OR SYSTEM 2 4
--
16 OHMS16 OHMS
SYSTEM 1 AND SYSTEM 2 8SYSTEM 1 AND SYSTEM 2 8
--
16 OHMS16 OHMS
SPEAKERSSPEAKERS
RR
LL
MAIN INMAIN IN
LL
RR
PRE OUTPRE OUT
GNDGND
RR
LL
CDCD AUXAUX
//
DVDDVD
TUNERTUNER
OUTOUTININ
RECORDER 1RECORDER 1
OUTOUTININ
RECORDER 2RECORDER 2
AC INAC IN
RR
LL
RR
OFFOFF
SEPARATESEPARATE
OUTOUT
ININ
REMOTEREMOTE
CONTROL CONTROL
SERIAL NO.SERIAL NO.
PHONOPHONO
ONON
RL
SYSTEM 1
SYSTEM 2
A C D E F
GH
I
JKLM
B
H SEPARATE switch
This switch is used for selecting the pre-amplifier and main-
amplifier connection modes.
OFF: Select this position when the amplifier is used as a
normal integrated amplifier. (Standard factory set-
ting)
ON: The pre-amplifier and main-amplifier are separated.
The PM7001 can be used as a main-amplifier when
input is connected to the MAIN IN jacks D.
I RECORDER 1/RECORDER 2 output jacks
These jacks are for connecting to the recording input jacks
of a CD-R recorder, MD deck, tape deck, etc. Output sig-
nals can be selected using the REC SELECTOR knob !2
on the front panel.
J RECORDER 1/RECORDER 2 input jacks
These jacks are for connecting to the output jacks of a CD-
R player, MD deck, tape deck, etc.
K AUX/DVD input jacks
These jacks are for connecting to the output jacks of a
DVD player or other LINE component.
L TUNER input jacks
These jacks are for connecting to the output jacks of a
tuner or other LINE component.
M CD input jacks
These jacks are for connecting to the output jacks of a CD
player or similar component.
!3 Infrared Receptor Window
This is the receptor of control signals sent from the
RC4001PM remote controller. Point the remote controller
towards this window to properly transmit signals.
!4 PHONES jack
This jack is for connecting headphones with a standard
stereo plug. To listen with headphones, turn the speaker
output OFF by setting the SPEAKERS 1 and 2 buttons o
in the OFF position.
PM7001U 01 Eng(P06-P15) 06.1.19, 4:03 PMPage 7 Adobe PageMaker 6.5J/PPC