000009893 - 21/12/2021 Assembly Guide Model: 2GMCC Fortress 31.5" Mobile Garage Cabinet With Drawer And Shelves Stuck? Questions? We are here to help. 1-888-230-2225 help@manhattancomfort.
In order to ease the assembly, you should separate and identify the parts first Necessary hardware for the assembly * Included in the kit * Not included in the kit Locking nut, no key tightening required. Do not place the parts directly onto the floor. Use a cardboard sheet or a mat to place the parts, during the separation and assembly. Stuck? Questions? We are here to help. 1-888-230-2225 help@manhattancomfort.
Fortress 31.
STEP 1 1 - Fit part P7 inside part P3 2 - Fit both parts in the frontal side, with F1 and F2. 1 F1 4x F2 P3 4x 2 P7 WARNING Do not tighten the screw completely. STEP 2 1 - Fit part P2 inside part P7 2 - Fit both parts in the frontal side, with F1 and F2. F1 1 4x F2 4x P3 P7 WARNING Do not tighten the screw completely.
1 - Fit part P5 between part P2 and P3 2 - Check that all 4 tabs have been fitted 3 - Fit part P5 to parts P2 and P3, at the frontal side, with F1 and F2. STEP 3 F1 1 4x F2 2 4x P5 P3 P7 P2 3 WARNING Do not tighten the screw completely. STEP 4 1 - Turn the cabinet with the back side upwards. F1 2 - Fit parts P2 and P3 to parts P5 and P7 with F1 and F2. Do not tighten the screw completely.
STEP 5 1 - Fit part P10 into parts P2, P3 and P5 Check that all fits are supported over the bolts. 2 - After fitting the parts, screw the bolts until locked. 1 P10 WARNING P2 2 P5 Position part P10 on the P5 side for mounting the cabinet. P3 P7 Do not tighten the screw completely.
STEP 7 3 - To assembly the cabinet with caster, align the F10 and F11 to the holes in part P7 and fix them with F1 and F2. 4 - WARNING: Casters with lock (F11) must be fitted in the frontal side of the cabinet 1 - Put the cabinet a flat surface. 2 - Completely tighten all screws. F10 2x F11 P3 2x P5 F1 P7 P2 16x E C FA F2 AT R SU FL WARNING After tightening the screws, make sure the cabinet does not appear to be misaligned.
STEP 9 1 - Fit the lower part P19 in diagonal position to insert it inside the cupboard 2 - Lean part P19 in part P2, P3 and place it over the F7 detailed in the figure here below 3 - Lower the other side of part P19, leaning it over the left F7 F7 P5 P3 P19 P2 P7 STEP 10 1 - Fit the lower part P17 in diagonal position to insert it inside the cupboard. 2 - Fit part P17 in cut-offs of parts P2 and P3, as detailed here below 3 - Fix part P17 in parts P2 and P3, with F1 and F2.
STEP 11 1 - To assembly the doors, fit door P26 lower hinge bolt inside the bushing fixed in part P7. Then, pull down the pin of door P26 upper hinge; align the door and release the pin to fit the bushing fixed in part P17. 2 - Repeat the step for part P27. 1ยบ P5 P2 P19 P17 P26 P3 P7 P27 STEP 12 1 - Fit part P15 in part P28. 2 - Screw the two parts with F18.
1 - Align parts P12 and P13 on part P15 and slide to part P28. 2 - Screw the two parts with F18. STEP 13 F18 6x P13 P12 P15 P28 STEP 14 1 - Insert part P14 over part P15 and between parts P12 and P13. 2 - Then, fix part P14 to parts P12, P13 and P15, with F18.
STEP 15 1 - Fit the drawers - already assembledbetween parts P2 and P3, through the drawer slides. 2 - Check that the drawer slides on both sides are properly fitted. If they are not properly fitted, the drawer will not close completely. Slide the drawer in and out to test it and be sure it is sliding smoothly.
FORTRESS GARAGE WARRANT S TERMS This product has the guarantee for a period of twelve (12) months, this limited warranty is effective from the date of the original consumer purchase. Proof of original purchase date is required to obtain service or replacement under this limited warranty. Once the defect of manufacture has been verified, the consumer should contact the store where he purchased the product.
