Operation Manual

8 ENGLISH
Toremovetheapplicationtool,loosenandremovethe
applicationtoolinstallationboltusingahexwrenchand
then take off the application tool.
Whenusingthetoolasasander,setasandingpaper
onthesandingpad(hookandlooptting).
Make sure that their shape and dust extraction holes
match each other when setting.
►Fig.8: 1.Sandingpad2.Tighten3.Sandingpaper
Toremovethesandingpaper,raiseitsendandpeelit
off.
Whenusingapplicationtoolswithadifferenttypeof
installation section, use a correct adapter (optional
accessory).
►Fig.9: 1.Applicationtoolinstallationbolt2. Holes in
the application tool 3.Adapter(requiredfor
some application tools) 4.Protrusionsofthe
toolange
Hex wrench storage
►Fig.10: 1. Hex wrench
Whennotinuse,storethehexwrenchasshowninthe
guretokeepitfrombeinglost.
OPERATION
WARNING: Before starting the tool and
during operation, keep your hand and face away
from the application tool.
CAUTION: Do not apply excessive load to the
tool which may cause a motor lock and stop the tool.
CAUTION: Do not operate the tool with press-
ing the battery cartridge against the tool.
Cutting, sawing and scraping
CAUTION: Do not move on the tool forcibly
in the direction (eg. towards either side) of tool
application with no cutting edge. It may damage
the tool.
►Fig.11
Puttheapplicationtoolontheworkpiece.
Andthenmovethetoolforwardsothattheapplication
tool movement does not slow down.
NOTE: Forcing or excessive pressure on the tool may
reduceefciency.
NOTE: Before cutting operation, it is recommended to
presettheorbitalstrokerate3-5.
Sanding
CAUTION: Do not reuse a sanding paper used
for sanding metal to sand wood.
CAUTION: Do not use a worn sanding paper
or sanding paper without grit.
Applyasandingpaperontheworkpiece.
►Fig.12
NOTE: Using a test material sample to try is recom-
mendabletodetermineacorrectorbitalstrokerate
suitableforyourwork.
NOTE: Use a sanding paper with the same grit until
sanding the whole workpiece is completed. Replacing
a sanding paper with different grit sanding paper may
notgetanenish.
Dust extraction attachment
Optional accessory
CAUTION: Do not use the dust extraction
attachment when sanding metal.Suckingspark
and hot particle results in smoking and ignition.
►Fig.13: 1. Dust nozzle 2. Joint 3. Dust attachment
4.Nozzleband5. Holes in the tool 6. Felt
ring 7.Sandingpad8.Applicationtool
installationbolt
1. Installjoint,dustnozzleanddustattachment.
2. Installthenozzlebandonthetoolsothatitspro-
trusionstintheholesinthetooltosecureit.
3. Putthefeltringandthesandingpadonthedust
attachment and then secure them with the application
toolinstallationbolt.
Toperformcleaneroperation,connectavacuum
cleaner to the tool. Connect a hose of vacuum cleaner
to the dust extraction attachment (optional accessory).
►Fig.14
MAINTENANCE
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers, always using Makita replacement parts.