ENGLISH INSTRUCTION MANUAL Rotary Hammer HR3200C HR3210C HR3210FCT 008536 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH SPECIFICATIONS Model Concrete HR3200C HR3210C Tungsten-carbide tipped bit 32 mm Core bit 90 mm Capacities Steel 13 mm Wood 32 mm No load speed (min-1) 315 - 630 Blows per minute 1,650 - 3,300 Overall length 398 mm Net weight 4.4 kg Safety class HR3210FCT 424 mm 4.8 kg 5.0 kg /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Note: Specifications may differ from country to country.
ENG215-1 Vibration The vibration total value (tri-axial vector determined according to EN60745-2-6: Work mode : chiseling function Vibration emission (ah,CHeq) : 7.5 m/s2 Uncertainty (K) : 1.5 m/s2 Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN Authorized Representative in Europe: Makita International Europe Ltd.
21. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 22. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 23. Use the power tool, accessories and tool bits etc.
8. 9. 10. 11. 12. 13. 14. Lighting up the lamps used for a long time, let the tool warm up for a while by operating it under no load. This will loosen up the lubrication. Without proper warm-up, hammering operation is difficult. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. Hold the tool firmly with both hands. Keep hands away from moving parts. Do not leave the tool running. Operate the tool only when hand-held.
Selecting the action mode The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. • Rotation with hammering Changing the quick change chuck for SDS-plus 1 For Model HR3210FCT The quick change chuck for SDS-plus can be easily exchanged for the quick change drill chuck. Removing the quick change chuck for SDS-plus 1 2 2 1 1. Lock button 2. Pointer 3. Change lever 2 3 1. Quick change chuck for SDS-plus 2.
action mode positions. CAUTION: Always use the side grip to ensure operating safety when drilling in concrete, masonry, etc. The side grip swings around to either side, allowing easy handling of the tool in any position. Loosen the side grip by turning it counterclockwise, swing it to the desired position and then tighten it by turning clockwise. Torque limiter • The torque limiter will actuate when a certain torque level is reached. The motor will disengage from the output shaft.
Bit angle (when chipping, scaling or demolishing) Use the dust cup to prevent dust from falling over the tool and on yourself when performing overhead drilling operations. Attach the dust cup to the bit as shown in the figure. The size of bits which the dust cup can be attached to is as follows. 1. Change lever 2. Lock button 3. Pointer 1 2 Bit diameter 6 mm - 14.
After drilling the hole, use the blow-out bulb to clean the dust out of the hole. For Model HR3200C,HR3210C Use the optional drill chuck assembly. When installing it, refer to "Installing or removing the bit" described on the previous page. Set the change lever so that the pointer points to the symbol. For Model HR3210FCT Use the quick change drill chuck as standard equipment. When installing it, refer to "changing the quick change chuck for SDS-plus " described on the previous page.
Lubrication 1. Screws CAUTION: • This servicing should be performed by Makita Authorized or Factory Service Centers only. This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. Lubricate the tool every time the carbon brushes are replaced. Run the tool for several minutes to warm it up. Switch off and unplug the tool. 1 008603 1. Screws Align the change lever with the symbol , loosen the five screws and then remove the crank cap.
ACCESSORIES To reassemble the tool, follow the disassembling procedure in reverse. • CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Corporation Anjo, Aichi, Japan 884769-228 12