Sharpener 200 mm (7-718") MODEL 9820-2 INSTRUCTION MANUAL SPECIFICATIONS Wheel size 200 mm x 25 mm x 75 mm (7-7/8" x 1" x 3") No load speed 560 R/min. Overall length 390 mm ( 1 5-3/8") Net weight 1 1 kg (24.
BEFORE CONNECTING YOUR TOOL TO A POWER SOURCE Be sure you have read all GENERAL POWER TOOL SAFETY RULES GENERAL SAFETY PRECAUTIONS (For All Tools) 1. KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the . tools applications and limitations, as well as the specific potential hazards peculiar t o it. 2. KEEP GUARDS IN PLACE and in working order. 3. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on.
17. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended accessories. The use of improper accessories may cause risk of injury t o persons. 18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. 19. CHECK DAMAGED PARTS.
GROUNDING INSTRUCTIONS . . ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current t o reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
ADDITIONAL SAFETY RULES 1. Use only wheels having a maximum operating speed at least as high as "No Load RPM" marked on the tool's nameplate. 2. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 3. Secure the wheel carefully. 4. Be careful not t o damage the spindle or the bolt, or the wheel itself might break. 5. Keep a space of 5 m m (3/16") between the sharpening platform guide (rail) and the grinding wheel. 6.
HOW TO USE Replacing grinding wheel Use the wrench provided to release the grinding wheel by turning the installation screw counterclockwise. To install the grinding wheel, follow the removal procedure in reverse. Adjusting wheel guard The top of the wheel guard should be 1 mm (approx. 1/3") below the surface of the grinding wheel. Adjust height by turning the guard clockwise to lower it, or counterclockwise to raise it.
Loosen the pole fastening screws and lift off the sharpening platform guide. To install the sharpening platform guide, follow the removal procedure in reverse. Adjusting sharpening platform guide In using the sharpening platform guide to sharpen blade/knife, adjust the angle adjustment screw to the desired blade/knife sharpening angle. The bevel becomes acute as the angle adjustment screw is turned clockwise. The platform poles are fixed in place by tightening the pole fastening screws on either side.
The nut for raising or lowering the pole on either side raises the pole 0.5 mm (1/32") for each graduation, when turned clockwise, and it lowers the pole, conversely, 0.5 mm (1/32") when turned counterclockwise. Tilt the sharpening platform guide slightly with right side downward so that the blade contacts the right side surface of the grinding wheel.
Screw in clockwise the forward adjust screw on the right until the right upper edge of the blade comes into contact with the grinding wheel. Then fully tighten the fastening screw on the far right. Slide the holder to the right across the sharpening platform guide. Screw in the left-hand forward adjust screw until the left upper edge of the blade contacts the grinding wheel. Now use all four fastening screws to secure the blade on the horizontal.
Adjusting coolant flow Put water in the coolant reservoir. Turn the knob so that the marking i s positioned vertically to make the coolant flow. Turn the marking to the horizontal position to stop the coolant flow. NOTE : Adjust the coolant flow adequately. If the debris from the grinding wheel and the blade is washed away by the coolant, the coolant flow is excessive. Draining used coolant The used coolant drains out through the drain hose (vinyl tube) provided.
Switch action To start the tool, press the ON side of the switch located on the front of the tool. To turn the tool off, press the OFF side of the switch. Sharpening blade/knife 1 1 After you have established the correct coolant flow, you can begin sharpening. Sharpen with the cutting edge away from you, holding the sharpening holder with both hands.
Sharpening power planer blades Sharpen your planer blades to a 40" angle. Power planer blade CAUTION : *Clean and dry the tool after operation. 0 Be sure that the tool is switched off, unplugged and drained before attempting to move the tool.
MAINTENANCE CAUTION : Always be sure that the tool i s switched off and unplugged before attempting to perform inspection and maintenance. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using makita replacement parts. ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified i n this manual.
Aug.-02-84 US 200 mm (7-7/8") SHARPENER Model 9820-2 Note: The switch and other part configurations may differ from country to country.
MODEL 9820.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
