\- n I 12.7 mm (1/2") 12.7 mm (1/2") MODEL 6900D MODEL 6900DW With Fast Charger INSTRUCTION MANUAL SPECIFICATIONS Model 6900D Capacities Impacts per minute Bolt size Square drive M8 - M 1 4 15/16" - 9 / 1 6 " ) No ME - M 1 0 15/16" load speed IRPMI High 1,500 1 LOW ,,300 9 6 V ~ I At high speed 1 , 0 0 0 kg.cm 172 ft.lbs1 Note 1 318") 12 7 mm 2,000 1,500 11/2"l I 1 nr Overall length A t low speed 400 kg.cm 129 tt.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
I 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3)product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 9000. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow. 5.
I ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anythiqg t o cover or clog the charger vents. 4. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material.
Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool.
e When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times. e If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Selecting correct socket Use a correct size socket for bolts and nuts.
Reversing switch and speed change switch action Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. Slide the speed change switch to the right for high speed (high tightening torque) or to the left for low speed (low tightening torque). Select the speed suitable for your bolt by referring to the figures listed under "Operation". CAUTION : Always check the direction of rotation before operation. .
Operation The proper tightening torque may differ depending upon the kind or size of the bolt. The relation between tightening torque and tightening time is shown in the figures below. Standard bo1t kg cm I f f .
Speed Type of bolt Tightening time High High tensile bolt M10 13/8") 3 seconds Low Standard bolt M 8 (5/16") 1 second Number of tightenings 90 450 CAUTION : If the tool i s operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. 10 . *..:k:: .. 5i i'i, .'i'..'.>. , ... .;:;. . :.,"! .. .'.' . j ,,I.::. .!_.:. "... . ..::,,:::.y . ... . _. ; : :?.\:.: .. ..... . ...... ...,... .
. ....,..: ... . i:: ...... .. . !. , .. . ...... ..?,,...>... .. ... .. ... . , . .. ... . . . .... . :.,.,..:. +:;.,I. ii ;;. . MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended mannuer. Socket (With pin and 0 ring) 0 ring for socket 213370-0 21 3405.1 0 Extension bar Part No. 133211-3 [With pin (Part No. 256036-91 and 0 ring (Part No.
........ . .. ,...:. , ..h:; .:.!..i:.. ? .. : ... . ._._ .. ..:, ... f.. ... ..:... . .. .. ; .. .. 'I .;:.$,: , 1'. 8 , 1 . ... . ,,.,, , . ' Phillips bit (Use with bit adapter) Bit adapter Part No. 134530-0 [With pin (Part No. 256095-3) and 0 ring (Part No. 213370-O)] For driving machine screws. 784208- 1 45 (1-3/4") 1 2 V Fast charger Model D C 9 0 1 2 Fast charger Model D C 9 1 0 0 Plastic carrying case Part No. 8 2 4 3 1 0 - 9 Battery cartridge 9 0 0 0 Part No.
Juna-Ol-'BB @-- US 12.7 mm (1/2") CORDLESS IMPACT WRENCH Model 6900D Note: The switch and other part configurations may differ from country to country. 14 .. . .. . . .
June-03-'88 MODEL 69000 $$D DESCRIPTION O ";M ' $&, US DESCRIPTION MACHINE 1 2 3 4 5 6 7 0 9 10 11 I 1 1 1 1 1 1 I 1 1 1 12 I 13 I4 15 16 17 18 19 1 - I 1 1 1 I 1 - Pan Head Screw M3x14 lWilh Washer1 Switch Pan Head Screw M3.14 lWith Washer1 TrlOga, Compression Spring 2 Hausmp S.1 lWith Item 201 L..l SP" LWa, PI.". 0.anng 4 Gem Complete 11 -43 PI.". n..rmg 4 DC Motor 9 6 V ORmp 17 Flat W a s b t 16 0.11 0eanng 627L0 Spmdl. compra..mn sp,mp I9 W..b, 1628 Thrust 0.
MAKmA LIMITED ONE YEAR WARRANTY Warranty Policy I Fvery Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from w o r k a n s h i p and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.