Drill 10 mm (318") MODEL 6408 Variable speed I Reversing INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATI0 NS Drilling capacities Steel 10 m m (318") No load speed (RPM) Wood I 25 m m (1") 1 0 - 2,500 Overall length I 261 mm (10-9132'7 * Manufacturer reserves t h e right t o change specifications w i t h o u t notice. * Note: Specifications may differ f r o m country t o country. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2.Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal inj ury. 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 14.
Specific Safety Rules 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its o w n cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 3. Hold the tool firmly. 4. Keep hands away from rotating parts. 5. Do not leave the tool running. Operate the tool only when hand-held. 6.
SYMBOLS The reference below describes symbols used for this tool and others. volts amperes herts kilograms hours minutes seconds alternating current % ................................ direct current ................................ no load speed ................................ alternating or direct current /01 Class II Construction A splash-proof construction bb watertight construction .../min ............................... c5 ................................
Installing or removing drill bit CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the bit. Hold the ring and turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. To remove the bit, hold the ring and turn the sleeve counterclockwise. Switch action Tool speed is increased by increasing pressure on the trigger.
Reversing switch action The reversing switch changes the direction of rotation. Move the reversing switch lever to the position for clockwise rotation. Move the reversing switch lever to the ''9'' position for counterclockwise rotation. ''e" Reversing switch lever CAUTION : *Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. *Always check the direction of rotation before drilling.
Drilling operation *Drilling in wood When drilling holes in the wood, use a wood drill with a guide screw. The guide screw makes it bore naturally by itself, so you do not need to apply any pressure to the tool. *Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center Service centers are listed on the warranty card packed with your tool CAUTION These accessories or attachments are recommended for use with your Maktta tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Key
May-14-'96 US 10 mm (318") DRILL Model 6408 Note: The switch and other part configurations may differ from country to country.
M O D E L 6408 May-14-'96 $tDDESCRIPTION MACHINE US DESCRIPTION ",':;I MACHINE ~ :; 1 ; ~ Housing Set (With Item 191 Name Plate Tapping Screw 4 x 1 8 14 2 Switch Keyless Drill Chuck 10 Gear Complete Ball Bearing 6 2 6 2 Field Ball Bearing 6 2 7 2 ARMATURE ASSEMBLY (Wifh Item 9 11 & 121 201 Ball Bearing 8272 Carbon Brush Brush Holder Tapping Screw 4 x 1 8 Strain Relief Cord Guard Cord Housing Set [With Item 11 Makita Label Note The switch and other part specifications may differ from countr
MAKITA LIMITED ONE YEGK-7 Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
