OWNER'S MANUAL MODEL: P-14PE For any service needs, call 1-855-368-8606 Before operating this product, please read the instructions carefully and save this manual for future use.
Read This Manual Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the Troubleshooting Tips section (page 15 ).
CONTENTS SAFETY PRECAUTIONS Safety rules . .......................................................................................................................................2 Operating conditions ..........................................................................................................................2 Electrical information .........................................................................................................................
SAFETY PRECAUTIONS Safety rules To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation may cause harm or damage. ! Always do this Never do this Your air conditioner should be protected from moisture. e.g. condensation, splashed water, etc. Do not place or store your air conditioner where it can fall into water or any other liquid. Unplug immediately.
PARTS IDENTIFICATION WARNING For your safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from the power cord. WARNING Electrical Infor mation Be sure the power requirement is adequate for the model you have chosen.
PARTS IDENTIFICATION NAME OF PARTS 1 Front 2 4 1 Control Panel 2 Horizontal Louver Blade (swings automatically) 3 Caster wheels 4 Carrying Handles (on each side) 1 Control Panel 2 Horizontal Louver Blade (operate manually) 3 Remote signal receptor 4 Caster wheels 5 Carrying Handles (on each side) 3 Fig.1 Model A 1 2 3 5 4 Model B Fig.2 Rear 6 6 Upper Air Filter (Behind the grille) 7 Air Outlet 8 Power cord outlet 9 Air intake 9 10 12 7 11 8 10 Drain Outlet 13 Fig.
AIR CONDITIONER FEATURES ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote controller and all its functions, then follow the symbols for the functions you desire. The unit can be controlled by the unit control panel itself with the remote control . NOTE: This manual does not include Remote Controller Operations, see the <> packed with the unit for details.
OPERATING INSTRUCTIONS 8 ION button(optional) Press the ION button, to activate the ion generator which will help to remove pollen and impur ities from the air, and trap them in the filter. Press again to stop. - 9 SWING button (Applicable to the models with auto swing feature only) Press to change the louver angle. Press and hold the button to initiate the Auto-Swing feature. Operating Instructions COOL mode - Press the "MODE" button until the "COOL" indicator light comes on.
OPERATING INSTRUCTIONS Other features Auto-Restart(only on some models) If the unit shuts off unexpectedly due to power outage, it will resume with the previous operation automatically when the power comes back on. Adjust manually Wait 3 minutes before resuming operation After the unit has been turned off, it cannot be restarted immediately. This is to protect the unit from malfunction. Operation will automatically restart after 3 minutes have passed.
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Placement B The air conditioner should be placed on a firm foundation to minimize noise and vibration. For safe and secure placement , place the unit on a smooth, level floor. A A:1-3 ft B: The unit has casters for easy mobility, but it should only be rolled on smooth, flat surfaces. Use caution when rolling on carpet surfaces. Do not attempt to roll the unit over objects. 1 ft Fig.
INSTALLATION INSTRUCTIONS Fig.10 Foam seal A (adhesive type) Fig.11 Window kit 26.5 ~ 48.0 Installation in a double-hung sash window 1. Cut the foam seal(adhesive type) to the proper length and attach it to the window sill. Fig.10 2. Attach the window slider kit to the window silll. Adjust the length of the window slider kit according to the width of window, shorten the adjustable window kit if the width of window is less than 26.5 inches.
INSTALLATION INSTRUCTIONS Fig.14 Foam seal A (adhesive type) Window panel Fig.15 26.5 ~ 48.0 Installation in a sliding sash window 1. Cut the foam seal(adhesive type) to the proper length and attach it to the window frame,Fig.14. 2. Attach the window slider kit to the window sill. Adjust the length of the window slider kit according to the width of window, shorten the adjustable window kit if the width of window is less than 26.5 inches.
INSTALLATION INSTRUCTIONS NOTE: Please seal the white foam seal (supplied) between the window kit and the window sill when there is the gap between them as shown below: Window kit Gap Window kit White foam seal Seal the white foam seal Window sill Window sill (Fig.A) (Fig.A1) Window kit Gap Window frame or wall Window kit White foam seal Window frame or wall Seal the white foam seal (Fig.B) (Fig.
INSTALLATION INSTRUCTIONS Exhaust hose installation: The exhaust hose and adaptor must be attached or removed in accordance with the usage mode. COOL,HEAT(heat pump type) or AUTO mode Fig.18 FAN, DEHUMIDIFY or HEAT(electrical heat type) mode Attach Remove 1. Install the window Exhaust adaptor B onto the exhaust hose as shown in Fig.18. Refer to the previous pages for window kit installation. 2. Place the Exhaust hose over against the air outlet opening hook(See Fig.19) and flat the other end(See Fig.
INSTALLATION INSTRUCTIONS Remove the drain plug Water drainage: - During dehumidifying modes, remove the drain plug from the back of the unit, install the drain connector(5/8 universal female mender) with 3 4 hose(locally purchased). For the models without drain connector, just attach the drain Fig.22 hose to the hole. Place the open end of the hose directly over the drain area in your basement floor. Please refer to Fig.22 & 23. Continuous drain hose Fig.
CARE AND MAINTENANCE CARE AND MAINTENANCE Air filter (slide out) Fig.25 Remove three screws and take the air intake grille down IMPORTANT: 1) Be sure to unplug the unit before cleaning or servicing. 2) Do not use gasoline, thinner or other chemicals to clean the unit. 3) Do not wash the unit directly under a tap or using a hose. It may cause electrical danger. 4) If the power cord is damaged, it should be repaired by customer service or the manufacturer. 1. Air filter - Fig.26 - Fig.
TROUBLESHOOTING TIPS TROUBLE SHOOTING PROBLEM 1. Unit does not start when pressing ON/OFF button SOLUTION - P1 appears in the display window. Drain the water in the bottom tray. - Room temperature is lower than the set temperature.(Cooling mode) Reset the temperature. - The windows or doors in the room are not closed. Make sure all the windows and doors are closed. - There are heat sources inside the room. Remove the heat sources if possible. 2.
MAGNAVOX and SMART. VERY SMART are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V.
