Instructions / Assembly

ManualsBrandsLTL Home Products ManualsAccordion Doors36 in. x 80 in. Woodbridge Vinyl Nutmeg Accordion Door

Marquis

/Woodbridge Installation Instructions

For quick and easy installation of your folding door, read

these instructions thoroughly.

The Tools You Will Need

You will need a Drill, Phillips screwdriver bit, 3/32” drill bit for

pilot holes, small Phillips head screwdriver, tape measure,

pencil, ne tooth hacksaw (for cutting the top track), safety

glasses and ne sandpaper (can be used to smooth edges

after cutting top track) and a level.

Make sure all of the following Parts are

included before you begin:

Door Parts Location

SINGLE DOOR INSTALLATION

1. Measure the Door Opening

Measure the height

and width of your

nished open-

ing. This door ts

openings that are

24” to 36” wide

and 80” high.

If the height of your

door opening is

approximately 80”,

you will not need

to alter the height of the door. If the opening is less than 80”

high, the door may be shortened by sawing the excess from

the bottom of the door panels.

Trimming the Door Height and Top Track:

Stack the door panels together and secure with masking

tape. Remove bottom hinge screws. Cut excess o with a

hacksaw or le.

2. Install the Top Track

Cut the top track

1/8” shorter than the

width of the nished

opening. Position the

top track in the top of

the door

opening so that it is

straight and cen-

tered. After making a

pilot-hole (with

a 3/32” drill bit),

insert a 1” track

screw through the

pre-drilled hole nearest the center of the track. Do not fully

tighten. (Tape may be used to hold the track in place while

you mark and drill.)

3. Attach the Door Knob

Take the male

handle and

remove the

screw. Put the

screw through

the inside of the

female handle

and insert the

screw through

the pre-drilled

handle hole on

the lead edge.

Take the male

handle and line it

up with the screw shaft on the other side of the door. Tighten

with screwdriver until secure.

Snap the cover onto the female handle.

2 Piece

Door Knob

1 Ea. 36” Top

Track

1 Ea.

Closure

Channel

5 Ea.

Anchor

Channel Clips

6 Ea. (1”)

Track Screws

12 Ea.

(1”) Flat Head

Screws

1 Ea.

Door Latch

1 Ea.

Door Knob Screw

Anchor

Channel

Clips

Top Track

Closure

Channel

Door

Latch

Door Knob

1 Door

Knob

Cover

Top Glide

Anchor

Panel

Lead

Edge

2 Door Key

Door Knob

Cover

1 Ea. Spare

Top Glide

1 Ea.

Spare Top

Glide Screw

Summary of content (3 pages)

PAGE 1
Marquis/Woodbridge Installation Instructions For quick and easy installation of your folding door, read these instructions thoroughly. The Tools You Will Need You will need a Drill, Phillips screwdriver bit, 3/32” drill bit for pilot holes, small Phillips head screwdriver, tape measure, pencil, fine tooth hacksaw (for cutting the top track), safety glasses and fine sandpaper (can be used to smooth edges after cutting top track) and a level.
PAGE 2
Marquis Installation Instructions 4. Hang Door onto Track Swing one end of the top track outward. Decide if the door will open from the left or the right, then slide all of the top glides onto the track. Stack the panels together near the center screw. Swing the track back to its original position. 6. Install the Anchor Channel Clips and Secure the Anchor Panel Use the closure channel to measure and align the channel clips. Align the channel on the non-opening side of the door jamb.
PAGE 3
Marquis Installation Instructions DOUBLE DOOR INSTALLATION 1. Measure the Door Opening Divide the width of the opening by two. Cut each top track to this measurement so that when installed, the tracks butt against one another in the center of the door opening. 2. Install the Top Track On a center line drawn across the top of the door opening, install either track and install all screws in this track. You will install the remaining track later. 3.