Poolroom SHOWER DOOR Shower Door Installation Instructions Reversible For a Left or Right Door | | Please Do Not Return the Product to the Store. | | Contact us with any questions.
SHOWER DOOR Model Specific Preparation A REQUIRED: Installation wall must be plumb o nL 3/8” (10mm) Out-of-Plumb Adjustment within the Wall Profile; Verify threshold and walls with a level.
PACKAGE CONTENT PACKAGE CONTENT PART# DESCRIPTION QTY PART# DESCRIPTION QTY A Bottom Gasket 1 F Magnetic strip 1 Magnetic Seal B Door panel 1 G Aluminum channel ! Cc Wall Jamb 1 H U channel 1 D Top Cover Cap 1 Alu.
SHOWER DOOR PACKAGE CONTENT Wall anchor Decorative Caps Screw | | @6x38mm ST4*30 washer) ST4*10 || Wood 7 pcs 7 pcs PCs 7 pcs | 1 pcs A 1 piece for each as spare part.
SHOWER DOOR TOOLS REQUIRED Drill Bits Screw Driver Drill AN 5 dia.
SHOWER DOOR SAFETY INFORMATION CAUTION Please carefully read the following important safety information before handling or installing this shower. There is a risk of serious injury while handling this product. To minimize these risks, please note: * Always wear safety glasses and gloves while handling. + Always follow the installation instructions. * Inspect glass for damage before installation.
Model Dimensions SHOWER DOOR A configuration dimensions: Product Height | Model width | Installation width | D (Opening) 30" 30" ~31 3/8" 2519/32" | < Ton 32 32" ~33 3/8" 27 19/32" 3/8" 29 19/32" 3/8" 31 19/32" 1 A = al "= al "= al "= al [EG adjustment g" MAX —T J adjustment 1" MAX adjustment 3" MAX Left pivot ‘( This model is reversible for right or left-hand NOTE door installation. The left-hand door installation is shown throughout this manual.
= . NOTE, Wall Jamb Installation with a level before marking the Confirm the Wall jamb is plumb location of the holes for drilling. 1 Tee a cx1 0 \ Wall Jamb | RN NOT «| Leave 20mm [25/32"] from edge of shower pan. E| Center the Wall jamb (C) on the Threshold.
SHOWER DOOR Wall Jamb Installation 3 silicone the back of the Wall Profile Stud is present behind the wall: drill a hole up to the stud, 7 | drill an pilot hole into the stud and NOTE | use the ST4.0 x 30mm Pan Head Screws (bb) Stud is present behind the wall: drill a @1/4” (6mm) hole and insert the Wall Anchors (aa) and use the ST4.0 x 30mm Pan Head Screws (bb).
SHOWER DOOR Door panel Installation The Door panel Profiles can be adjusted up to 3/8” within the Wall Jamb for overall width or to correct for out-of-plumb conditions within the model size. Screw them together after making final adjustments. Place wood shimmed) onto the threshold to provide proper spacing beneath the door glass. Make any final adjustments to the door so that it is level and plumb in the opening.
Magnetic Seal 2 Aluminum channel v1 U channel $d Keep flush SHOWER DOOR Magnetic strip Install to door panel TN 1. Magnetic strip Install to door panel. ‘NOTE | 2. Put F,G,H together before fasten the glass : ’ door,make all these parts keep flush.
Include the washers when | installing the ST4.0x10mm NOTE, Pan Head Screws (dd) and RN ’ Decorative Caps (cc) . Fasten the door panel After final adjustments, drill @1/8” holes in the Wall Jap (C). Drill only through the first layer of the Door panel Profile and install the ST4.
Determine the G & H position SHOWER DOOR Pencil Put F,G,H together, keep flush, mark the position on the wall. Center the Magnetic Seal Aluminum channel(G) and U channel (H) on the Threshold.
SHOWER DOOR U channel Installation U channel eo If a Stud is present behind the wall: drill a hole up to the stud, drill an pilot hole into the stud and / | use the S8T4.0 x 30mm Pan Head Screws (bb NOTE Stud is present behind the wall: drill a hole and insert the Wall Anchors (aa) and use the ST4.0 x 30mm Pan Head Screws (bb).
SHOWER DOOR Magnetic Seal Wall Jamb Installation ST4X10mm Include the washers when Pan Head Screw installing the ST4.0x10mm | | Make sure the magnetic Pan Head Screws (dd) and seals close properly! Decorative Caps (cc) .
Measure "X" and cut the Bottom Gasket same length as "X". SHOWER DOOR Top Cover Cap & Bottom Gasket Installation from pivot profile to magnetic 'NOTE| Pot P seal on the door.
Alu. Threshold Installation J Measure "X" and NOTE, cut the alu threshold | same length as 27mm [1 1/16 NOTE] \\ 17 SHOWER DOOR NOTE | "X" wall to wall width. “| The large curved lip of the dam strip is intended to face toward the outside of "| the shower to ensure the flow of water is redirected towards the drain.
SHOWER DOOR SEALING NOTE | The surfaces need to be clean and free of debris before applying silicone. | 7 i Ensure that the Shower door closes tightly and opens smoothly. NOTE Apply a good quality silicone sealant along the wall Water seal Allow 24 hours for the silicone to cure before using the shower. | Apply Silicone supplied).
SHOWER DOOR This troubleshooting guide is for general aid only. For service and installation issues or concerns, please contact us by hotlink + 1 302 336 8180. Troubleshooting Problem/Symptom Suggested Solution Page(s) *Check all shipping/packaging material for missing Missing parts parts/components. *If not found, please contact us by hotlink + 1 302 336 8180 to order factory part replacement. *Check the magnetic seal (F)for proper trimming and installation.