INSTALLATION GUIDE FINGERPRINT DEADBOLT
Connect with us @meetlockly | #LOCKLY
Welcome! This guide will walk you through step-by-step how to install and get your LOCKLY® up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: LOCKLY.com/support or call (669) 500-8835 for help.
INSTALLATION OVERVIEW AND PARTS LIST F H Parts List Labeled As Description A Keys Exterior E PE ive TA Adhes D I 2X B Exterior Assembly C Exterior D Mounting Plate E Adhesive Tape F Interior Assembly G PM5×60mm Screw H Battery Cover I PM4*12MM Screw J Deadbolt K KA4*20MM Screw L Strike Plate N Dust Box U Activation Card B G 2X A J N L U K 4X LOCK SERIAL PGDXXXXXXXXXXXXXXXX ACTIVATION CODE LOCKLY® Flex Touch can be fitted for both right swing doors and left sw
Preparation To complete installation, you would need the following: Phillips Screwdriver Flathead Screwdriver Tape measure or ruler Prepare door and remove existing lock. If necessary, use provided Installation Template to prepare door.
Step 1 ADJUST DEADBOLT AND INSTALL Deadbolt slot must align to the center of the door hole. Adjust as shown if needed. 2-3/4" (70mm) or 2-3/8” (60mm) The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8” (60mm) if necessary. (wear gloves to protect from possible pinching). B A B Push the crank A to extend the deadbolt B C C D Deadbolt comes set at 2-3/4" (70mm).
Step 1 ADJUST DEADBOLT AND INSTALL continued Extend the deadbolt by inserting a flat-head screwdriver into the slot and turning clockwise. Insert deadbolt to the door edge, make sure that the right side is up and the slot is in the vertical position. Secure with 2 K screws.
Step 2 INSTALLING EXTERIOR ASSEMBLY (B) Before mounting exterior lock assembly (B) make sure torque blade is in the vertical position while deadbolt is extended [1]. Place assembly and torque blade through the deadbolt slot and guide connection cables through the cross-bore hole under the deadbolt as shown. Align and secure until flush to exterior door surface.
Step 3 1: Check mounting plate D alignment to door hole before securing with adhesive strips. INSTALLING INTERIOR ASSEMBLY (F) 2: Align and secure mounting plate with adhesive strips. Guide connection cable through and secure to the lower left notched hole. Remove key when finished G 2X Leave deadbolt extended 3: Insert, tighten by hand 2 G screws located on the left and right of the blade. Check alignment and tighten with screwdriver until mounting plate is securely placed on door.
Step 3 INSTALLING NTERIOR ASSEMBLY (F) continued Plug the cable coming through mounting plate D into the interior assembly F as shown. Tuck cable under eyelet hooks and route to the right on interior assembly F . Y X Plug X into Y , match red side of plug with red on socket - insert tightly. NOTE: If you need to disconnect the cable, make sure to press the snap tab to release the plug before carefully pulling it out. Do not force, as this may result in damaging the lock.
Step 3 PROG RAM INSTALLING NTERIOR ASSEMBLY (F) continued RESET PROGR AM PROGR AM RESET Torque Blade RESET Thumb turn shaft I 2X Align torque blade with thumb turn shaft, make sure both are in the vertical position. Before placing the interior assembly onto the mounting plate, ensure the thumb turn is vertical. Place the interior assembly against the mounting plate and make sure the torque blade is inserted to the thumb turn shaft.
Step 4 INSTALLING BATTERIES PRESS & HOLD 1 2 3 4 1: With door open and deadbolt fully extended, place ribbon inside compartment and insert 3 batteries only (hold on inserting the 4th) in bottom row (note correct -/+ polarity). 2: Press and HOLD the program button, continue to hold and install the 4th battery. The lock will automatically start self-check (release program button once check starts).
Step 5 INSTALLATING DOOR STRIKE Use the supplied door strike or use your existing as long as deadbolt operates smoothly without binding or catching. K(2X) L N IMPORTANT: Because doors and frames vary in design, it may be necessary to make slight adjustments to your strike plate and/or dust box in order to ensure smooth deadbolt operation. This is very important.
Step 6 DOWNLOAD LOCKLY APP Congratulations! You have completed the LOCKLY Flex Touch lock installation. To complete its setup, download the LOCKLY app from the App Store or Google Play and follow on-screen instructions for adding a new lock. Scan or visit LOCKLY.com/app or Search & Download Directly on...
Add more Smart to your Home Secure Link Wi-Fi Hub Add the optional LOCKLY Secure Link Wi-Fi Hub, together with the free LOCKLY app, it's easier than ever to securely control and manage your door from anywhere, anytime. Grant access, even when you’re not home Lock and unlock door from anywhere. Real-time, monitoring, & status Monitor open/closed door status with real-time alerts sent to your smart phone, do matter where you are.
To download the latest digital copy of installation guide, user manual and/or watch instructional videos, go to LOCKLY.com/installation.
FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
We’re here to help! Email: help@LOCKLY.com For the most up to date version of this guide visit: LOCKLY.
