VISION SMART LOCK w/ HD VIDEO DOORBELL INSTALLATION GUIDE DEADBOLT EDITION
M-2 H 2x L-2 I M-1 L-1 G STEP 1: PREPARE DOOR FOR INSTALLATION K 4x F 2x J D E B Lockly Secure can be fitted for both right swing doors and left swing doors.
STEP 1: PREPARE DOOR FOR INSTALLATION 1.1: To complete installation, you would need the following: Flathead Screwdriver Phillips Screwdriver Screwdriver with drill bits (optional) Ruler 1.2: Prepare door and remove existing lock. If necessary, use provided Installation Template to prepare door.
STEP 2. ADJUST DEADBOLT AND INSTALL 2.1: Deadbolt slit hole must be aligned to the center of the door hole. If not adjust as shown below: 2.1.
STEP 2. ADJUST DEADBOLT AND INSTALL 2.2: Extend the deadbolt by inserting a flat head screwdriver on the slit hole or by pushing the crank towards the metal face plate. 2.
STEP 3. INSTALLING THE EXTERIOR ASSEMBLY 3.1: To secure Exterior Assembly of lock, peel the cover off the adhesive strips 3.2: Before placing the exterior assembly on the door, make sure the torque blade is in vertical position and the deadbolt is extended. Vertical When installing the exterior assembly, make sure the deadbolt is fully extended and the slit hole is vertically positioned on the bottom, the torque blade should be inserted in a vertical position. 3.
STEP 4. INSTALLING THE INTERIOR ASSEMBLY 4.1: Peel of the cover off the adhesive strip on the mounting plate. 4.2: Place the mounting plate on the interior side of the door. Guide the cable to the opening ear on the side of mounting plate and make sure the torque blade is at the center of the mounting plate. G(2X) 4.3: Without using any tools, insert 2 screws (G) on the side of the torque blade.
STEP 4. INSTALLING THE INTERIOR ASSEMBLY 4.5： Plug the cable that is coming through the door into the Interior lock. Make sure you match the direction of the plug correctly and matching the red side of the plug with the red side on the lock. Secure the connection by ensuring the snap is inserted tightly. In case you need to reinstall the lock and disconnect the cable, make sure to press the snap to release the plug before carefully pulling it out.
STEP 5. INSTALLING BATTERIES 5.1: First install 3 of the 4 batteries. Before installing the last battery, press and hold the PROGRAM button while installing the last battery until you hear a beep from Lockly. - + + + - + PROGRA M RESET Lockly will then perform a self check and the keypad screen will start to initiate. This self check will automatically determine and set your door lock to a left open or right open door.
STEP 6: INSTALLING THE DOOR STRIKE Install the door strike. Install the door strike to your door frame and proceed to the last step of installation of your new lock. You may use our supplied door strike or use your existing door strike as long as the dead bolt moves smoothly in and out of the door strike. As there are many types of doors, you may need to make slight adjustments so the dead bolt moves smoothly.
Certified FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2.
VISION For an online version of this installation guide and videos, visit: http://lockly.
