Instructions / Assembly

ManualsBrandsLNC ManualsLightingModern Transitional Wall Sconce 1-Light Brushed Gray Linear Rectangle Wall Light with Cylinder Seeded Glass Shade

  Weareheretohelp:support@lnchome.com

www.lnchome.comPage:  ‐1‐/4

ItemNumber:A03393

WARNING(Toreducetheriskoffire,electricshock,orinjurytopersons):

1. Wesuggestinstallationbyalicensedelectrician.

2. Pleasereadtheinstructioncarefullyandsaveitasyoumayneeditatlatertime.

3. Beforeyoustart,NEVERattemptanyworkwithoutshuttingofftheelectricityuntiltheworkisdone.A).Gotothemain

fuse,orcircuitbreaker,boxinyourhome.Placethemainpowerswitchinthe“OFF”position.B).Placethewallswitch

inthe“OFF”position.

4. Mountingsurfaceshouldbeclean,dry,flat,strongenoughand1/4”largerthanthecanopyonallside.Anygapsbetween

themountingsurfaceandcanopyexceeding3/16”shouldbecorrectedasrequired.

5. Makesurethattheceilingorwallcanstandtheweightofthelampbeforefixture.

6. Makesurethevoltageyouareusingis120V.Themaximumwattageis60Wperbulb.

7. Keepthelampawayfromacidicandbasicobjectsincaseofdamagingthesurfaceofthelamp.

8. Whenreplacingbulb,youshouldturnofforunplugthelampandyoumustwaituntilitiscoolasbulbsgethotquickly.

9. Thesafetyinstructionsappearinginthismanualarenotmeanttocoverallpossibleconditionsthatmayoccur.Itmust

beunderstoodthatcommonsense,cautionandcaremustbeusedwithanyelectricalproducts.



IMAGEFORFINISHEDPRODUCT：



Summary of content (4 pages)

PAGE 1
We are here to help: support@lnchome.com Item Number: A03393 WARNING (To reduce the risk of fire, electric shock, or injury to persons): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B).
PAGE 2
We are here to help: support@lnchome.com TOOLS REQUIRED (NOT INCLUDED): Before doing assembly and installation please prepare the needed tools as below picture PARTS TYPE & QTY INCLUDING: (B) Mounting plate (1) (C)Green ground screw (1) (E) Back plate (1) (F) Socket cap (1) (G) Ball nut (2) (H) Glass (1) ACCESSORIES & QTY ENCLOSED: (A)Plastic wire connector (3) (D) Mounting screw (2) ASSEMBLY & INSTALLATION INSTRUCTIONS: 1.
PAGE 3
We are here to help: support@lnchome.com 4. 1) Carefully pull the wires from outlet box through mounting plate (B) 2) Attach the mounting plate (B) to outlet box with mounting screws (D) 5. Make wire connections Connect wires as below wires connecting shown.
PAGE 4
We are here to help: support@lnchome.com 7. 1) Install bulb (not included) (Please do not exceed the maximum capacity recommended on the socket.) 2) Carefully and gently position the glass (H) on socket cap (F) 8. Check everything installed properly, then you could turn on the light. CLEANING To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.