READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For models: AK52BNK4L AK52EB4L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs. 4 - 5 Wiring. pg. 5 Canopy Assembly. pg. 6 Blade Assembly. pg. 6 Light Kit Assembly. pg. 7 Testing Your Fan. pg. 7 Troubleshooting. pg. 8 Parts Replacement. pg. 8 Warranty. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2. 3. 4.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. c b a a. hanging bracket. 1 piece b. canopy. 1 piece c. downrod and hanging ball (with pin & clip). 1 piece e d d. motor housing. 1 piece f e.
12ft. - 20ft. (3.66m - 6.1m) 3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 30 7 feet inches (2.13m) (76cm) This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling.
. Fan Assembly. If you wish to extend the hanging length of your fan, you must remove the hanging ball from the downrod provided to use with an extended downrod (sold separately). [If you wish to use the downrod provided, please proceed to instructions following the dotted line below.] Loosen set screw on hanging ball and remove pin and clip. Lower hanging ball and remove stop pin.
5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab. hanging bracket tab hanging ball slot WARNING: Failure to align slot in hanging ball with tab in hanging bracket may result in serious injury or death.
. Canopy Assembly. hanging bracket Temporarily raise canopy to hanging bracket to determine which 2 screws in hanging bracket align with slotted holes in canopy, and then lower canopy and partially loosen these 2 screws. Remove the other 2 screws and lock washers and set aside. screw Now, lift canopy to hanging bracket again, aligning slotted holes in the canopy with loosened screws in hanging bracket. Twist canopy to lock.
9. Light Kit Assembly. Install 2 medium base 6.5 watt LED bulbs, (included). IMPORTANT: When replacing bulbs, please allow bulbs and glass shade to cool down before touching. Align grooves on glass shade with nodules on inside edge of motor housing and push up gently on glass shade. Twist glass shade to the RIGHT (clockwise) until glass shade locks into place. Pull down VERY GENTLY on glass shade to make sure that glass shade is secure. bulb glass shade 10. Testing Your Fan.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. LITEX 30-YEAR LIMITED WARRANTY: LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or repair any fan which has faulty performance due to a defect in material or workmanship.