Page 3 of 57 Report No.: LCS210301192AS List of Attachments (including a total number of pages in each attachment): Attachment No.1: National Differences. Attachment No. 2: Photo documentation. Summary of testing: Tests performed (name of test and test clause): The submitted samples were found to comply with the requirements of: Electrical safety: Testing location: Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 57 Report No.: LCS210301192AS Copy of marking plate(s): The artwork below may be only a draft. Lintelek Smart Watch Model: ID205L Input: 5V 0.18A Battery: 3.8V 210mAh Importer: XXXX Address: XXXX IP68 Made in China Note: 1. The height of WEEE symbol ≥ 7.0mm. TRF No. IEC62368_1D Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 57 Report No.: LCS210301192AS TEST ITEM PARTICULARS: Classification of use by ................................................ : Ordinary person Instructed person Skilled person Children likely to be present Supply Connection ....................................................... : AC Mains DC Mains External Circuit - not Mains connected ES1 ES2 ES3 Supply % Tolerance .................................................... : +10%/-10% +20%/-15% +____%/ -_____% None Supply Connection – Type .
Page 6 of 57 Altitude of test laboratory (m) ................................... : 500 m or less Mass of equipment (kg) ............................................ : 0.035 kg Report No.: LCS210301192AS ______ m Possible test case verdicts: - test case does not apply to the test object ................. : N/A - test object does meet the requirement ...................... : P (Pass) - test object does not meet the requirement ................ : F (Fail) Testing Date of receipt of test item .............
Page 7 of 57 Report No.: LCS210301192AS ENERGY SOURCE IDENTIFICATION AND CLASSIFICATION TABLE: (Note 1: Identify the following six (6) energy source forms based on the origin of the energy.) (Note 2: The identified classification e.g., ES2, TS1, should be with respect to its ability to cause pain or injury on the body or its ability to ignite a combustible material. Any energy source can be declared Class 3 as a worse case classification e.g. PS3, ES3.
Page 8 of 57 Report No.: LCS210301192AS ENERGY SOURCE DIAGRAM Indicate which energy sources are included in the energy source diagram. Insert diagram below ☒ ES ☒ PS ☒ MS ☒ TS ☒ RS OVERVIEW OF EMPLOYED SAFEGUARDS Clause Possible Hazard 5.1 Electrically-caused injury Body Part (e.g. Ordinary) Energy Source (ES3: Primary Filter circuit) Ordinary Safeguards Basic Supplementar y Reinforce d (Enclosur e) ES1: +5Vdc input N/A N/A N/A Ordinary ES1: All internal circuits N/A N/A N/A 6.
Page 9 of 57 Body Part (e.g., Ordinary) Energy Source (Output from audio port) Ordinary RS1: Indicator light Report No.: LCS210301192AS Safeguards Basic Supplementar y Reinforce d N/A N/A N/A Supplementary Information: (1) See attached energy source diagram for additional details. (2) ―N‖ – Normal Condition; ―A‖ – Abnormal Condition; ―S‖ Single Fault TRF No. IEC62368_1D Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict 4 GENERAL REQUIREMENTS P 4.1.1 Acceptance of materials, components and subassemblies P 4.1.2 Use of components P 4.1.3 Equipment design and construction P 4.1.15 Markings and instructions .................................. : 4.4.4 Safeguard robustness 4.4.4.2 Steady force tests .............................................. : (See Annex T.2, T.4) P 4.4.4.3 Drop tests ............
Page 11 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict 5.2.2 ES1, ES2 and ES3 limits ES1 P 5.2.2.2 Steady-state voltage and current......................... : (See appended table 5.2) P 5.2.2.3 Capacitance limits ................................................ : N/A 5.2.2.4 Single pulse limits ................................................ : N/A 5.2.2.5 Limits for repetitive pulses ................................... : N/A 5.2.2.
Page 12 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause 5.4.2.3 Requirement + Test Result - Remark Verdict Determining clearance using required withstand voltage ................................................................. : N/A a) a.c. mains transient voltage ............................. : b) d.c. mains transient voltage ............................ : c) external circuit transient voltage ...................... : d) transient voltage determined by measurement .................
Page 13 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause 5.4.8 Requirement + Test Humidity conditioning Result - Remark Verdict N/A Relative humidity (%) ......................................... : Temperature (°C) ................................................ : Duration (h) ....................................................... : 5.4.9 Electric strength test .......................................... : N/A 5.4.9.1 Test procedure for a solid insulation type test N/A 5.4.9.
Page 14 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict 5.5.7.2 Use of an SPD between mains and protective earth N/A 5.5.8 Insulation between the mains and external circuit consisting of a coaxial cable .............................. : N/A 5.6 Protective conductor N/A 5.6.2 Requirement for protective conductors N/A 5.6.2.1 General requirements N/A 5.6.2.2 Colour of insulation N/A 5.6.
Page 15 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict Supply Voltage (V) ...............................................: Measured current (Ma) ........................................: Instructional Safeguard ........................................: N/A 5.7.6 Prospective touch voltage and touch current due to external circuits N/A 5.7.6.1 Touch current from coaxial cables N/A 5.7.6.
Page 16 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict 6.4.3 Reduction of the likelihood of ignition under single fault conditions in PS2 and PS3 circuits N/A 6.4.3.1 General N/A 6.4.3.2 Supplementary Safeguards N/A Special conditions if conductors on printed boards are opened or peeled N/A Single Fault Conditions ........................................ : N/A Special conditions for temperature limited by fuse N/A 6.4.
Page 17 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test 6.5.3 Requirements for interconnection to building wiring .................................................................... : 6.6 Safeguards against fire due to connection to additional equipment Result - Remark Verdict N/A P External port limited to PS2 or complies with Clause Q.1 N/A 7 INJURY CAUSED BY HAZARDOUS SUBSTANCES N/A 7.2 Reduction of exposure to hazardous substances N/A 7.
Page 18 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict 8.5.5 High Pressure Lamps N/A 8.5.5.1 Energy Source Classification N/A 8.5.5.2 High Pressure Lamp Explosion Test .....................: N/A 8.6 Stability N/A 8.6.1 Product classification N/A Instructional Safeguard ..........................................: 8.6.2 Static stability N/A 8.6.2.2 Static stability test N/A Applied Force ............................................
Page 19 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict 8.10.6 Thermoplastic temperature stability (C) ................ : N/A 8.11 Mounting means for rack mounted equipment N/A 8.11.1 General N/A 8.11.2 Product Classification N/A 8.11.3 Mechanical strength test, variable N ....................: N/A 8.11.4 Mechanical strength test 250N, including end stops N/A 8.12 Telescoping or rod antennas .................................
Page 20 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict 10.4.1.f) UV attenuation ..................................................... : N/A 10.4.1.g) Materials resistant to degradation UV ................. : N/A 10.4.1.h) Enclosure containment of optical radiation .......... : N/A 10.4.1.i) Exempt Group under normal operating conditions............................................................. : 10.4.2 Instructional safeguard .............
Page 21 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict B NORMAL OPERATING CONDITION TESTS, ABNORMAL OPERATING CONDITION TESTS AND SINGLE FAULT CONDITION TESTS P B.2 Normal Operating Conditions P B.2.1 General requirements......................................... : (See Test Item Particulars and appended test tables) P N/A Audio Amplifiers and equipment with audio amplifiers ............................................................ : B.2.
Page 22 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict B.4.9 Battery charging under single fault conditions ... : P C UV RADIATION N/A C.1 Protection of materials in equipment from UV radiation N/A C.1.2 Requirements N/A C.1.3 Test method N/A C.2 UV light conditioning test N/A C.2.1 Test apparatus N/A C.2.2 Mounting of test samples N/A C.2.3 Carbon-arc light-exposure apparatus N/A C.2.
Page 23 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict F.3.3.3 Nature of supply voltage...................................... : See copy of marking plate F.3.3.4 Rated voltage ...................................................... : See copy of marking plate F.3.3.5 Rated frequency .................................................. : F.3.3.6 Rated current or rated power .............................. : F.3.3.
Page 24 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause F.5 Requirement + Test Result - Remark Verdict e) Audio equipment terminals classified as ES3 and other equipment with terminals marked in accordance F.3.6.
Page 25 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict G.3.3 PTC Thermistors N/A G.3.4 Overcurrent protection devices N/A G.3.5 Safeguards components not mentioned in G.3.1 to G.3.5 N/A G.3.5.1 Non-resettable devices suitably rated and marking provided N/A G.3.5.2 Single faults conditions........................................ : N/A G.4 Connectors N/A G.4.1 Spacings N/A G.4.2 Mains connector configuration ..........................
Page 26 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict G.5.4.2 Test conditions P G.5.4.3 Running overload test N/A G.5.4.4 Locked-rotor overload test N/A Test duration (days) ........................................... : G.5.4.5 Running overload test for d.c. motors in secondary circuits N/A G.5.4.5.2 Tested in the unit N/A Electric strength test (V) ......................................
Page 27 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Strain relief test force (N) .................................... : Result - Remark Verdict G.7.3.2.2 Strain relief mechanism failure N/A G.7.3.2.3 Cord sheath or jacket position, distance (mm) .... : G.7.3.2.4 Strain relief comprised of polymeric material N/A G.7.4 Cord Entry .......................................................... : N/A G.7.5 Non-detachable cord bend protection N/A G.7.5.
Page 28 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict G.10.3.2 Voltage surge test N/A G.10.3.3 Impulse test N/A G.11 Capacitor and RC units N/A G.11.1 General requirements N/A G.11.2 Conditioning of capacitors and RC units N/A G.11.3 Rules for selecting capacitors N/A G.12 Optocouplers N/A Optocouplers comply with IEC 60747-5-5:2007 Spacing or Electric Strength Test (specify option and test results) .................................
Page 29 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict G.15.3.2 Creep resistance test N/A G.15.3.3 Tubing and fittings compatibility test N/A G.15.3.4 Vibration test N/A G.15.3.5 Thermal cycling test N/A G.15.3.6 Force test N/A G.15.4 Compliance N/A G.16 IC including capacitor discharge function (ICX) N/A a) Humidity treatment in accordance with sc 5.4.
Page 30 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict K.2 Components of safety interlock safeguard mechanism ......................................................... N/A K.3 Inadvertent change of operating mode N/A K.4 Interlock safeguard override N/A K.5 Fail-safe N/A Compliance .........................................................: N/A K.6 Mechanically operated safety interlocks N/A K.6.1 Endurance requirement N/A K.6.
Page 31 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict - Excessive discharging rate for any battery P M.3.3 Compliance ......................................................... : (See appended Tables and Annex M.3 and M.4) P M.4 Additional safeguards for equipment containing secondary lithium battery P M.4.1 General P M.4.2 Charging safeguards P M.4.2.1 Charging operating limits M.4.2.2a) Charging voltage, current and temperature .......
Page 32 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict M.8.1 General requirements N/A M.8.2 Test method N/A M.8.2.1 General requirements N/A 3 M.8.2.2 Estimation of hypothetical volume Vz (m /s)....... : M.8.2.3 Correction factors ................................................ : M.8.2.4 Calculation of distance d (mm) .......................... : M.9 Preventing electrolyte spillage N/A M.9.
Page 33 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict Tc (°C) ................................................................. : Tr (°C) ................................................................. : Ta (°C) ................................................................. : P.4.2 b) Abrasion testing ................................................. : N/A P.4.2 c) Mechanical strength testing .................................
Page 34 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause S.3 Requirement + Test Result - Remark Verdict Samples, material ............................................... : Wall thickness (mm) ............................................ : Conditioning (C) .................................................
Page 35 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict T.9.1 General requirements N/A T.9.2 Impact test and compliance N/A Impact energy (J) ................................................... : Height (m) .............................................................. : T.10 Glass fragmentation test ....................................... : N/A T.11 Test for telescoping or rod antennas N/A Torque value (Nm) ...........................
Page 36 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause 4.1.2 Requirement + Test Verdict TABLE: List of critical components Object / part No. Manufacturer/ trademark Technical data V-0, 120°C, Min. UL 94, 1.5mm UL 746 Sabic Innovative Plastics B V 940(f1) Internal wire Interchangeable Interchangeable PCB Interchangeable Shenzhen Sunhe Energy Co., Ltd Suizhou waveguide Electronics Co.
Page 37 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict TABLE: Lithium coin/button cell batteries mechanical tests 4.8.4, 4.8.5 N/A (The following mechanical tests are conducted in the sequence noted.) 4.8.4.2 TABLE: Stress Relief test Part Material Oven Temperature (°C) Comments -- -- -- -- 4.8.4.3 TABLE: Battery replacement test — Battery part no. ..............................................................
Page 38 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict TABLE: Lithium coin/button cell batteries mechanical tests 4.8.4, 4.8.5 N/A (The following mechanical tests are conducted in the sequence noted.) 4.8.5 TABLE: Lithium coin/button cell batteries mechanical test result N/A Test position Surface tested Force (N) Duration force applied (s) -- -- -- -- -- -- -- -- Supplementary information: 5.
Page 39 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause -- Requirement + Test -- -- Result - Remark Verdict Normal -- -- -- Abnormal -- -- -- Single fault – SC/OC -- -- -- -- 5.2.2.5 - Repetitive Pulses Parameters No. Supply Voltage Location (e.g.
Page 40 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Supplementary information: Note 1: Tma should be considered as directed by appliable requirement Note 2: Tma is not included in assessment of Touch Temperatures (Clause 9) 5.4.1.10.2 TABLE: Vicat softening temperature of thermoplastics N/A Penetration (mm) ................................................................
Page 41 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Clearance distanced between: Result - Remark Verdict Required withstand voltage Required cl (mm) Measured cl (mm) -- -- -- -- -- -- -- -- Supplementary information: 5.4.2.4 TABLE: Clearances based on electric strength test Test voltage applied between: N/A Required cl (mm) Test voltage (kV) peak/ r.m.s. / d.c. Breakdown Yes / No -- -- -- -- -- -- -- -- Supplementary information: 5.4.4.2, 5.4.4.
Page 42 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause 5.4.9 Requirement + Test Result - Remark Verdict TABLE: Electric strength tests Test voltage applied between: N/A Voltage shape (AC, DC) Test voltage (V) Breakdown Yes / No -- -- -- -- -- -- -- -- Routine Tests: Supplementary information: 5.5.2.
Page 43 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict 2* -- 3 -- 4 -- 5 -- 6 -- 7 -- Notes: [1] Supply voltage is the anticipated maximum Touch Voltage [2] Earthed neutral conductor [Voltage differences less than 1% or more] [3] Specify method used for measurement as described in IEC 60990 sub-clause 4.3 [4] IEC60990, sub-clause 6.2.2.7, Fault 7 not applicable. [5] (*) IEC60990, sub-clause 6.2.2.
Page 44 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict Circuit Location (x-y) Operating Condition (Normal / Describe Single Fault) Measured wattage or VA During first 30 s (W / VA) Measured wattage or VA After 30 s (W / VA) Protective Circuit, Regulator, or PTC Operated? Yes / No (Comment) Resistive PIS? Yes/No -- -- -- -- -- -- Supplementary Information: A combination of voltmeter, VA and ammeter IA may be used instead of a wattmeter.
Page 45 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause B.4 Requirement + Test Result - Remark TABLE: Fault condition tests Verdict P Ambient temperature (C) ............................................................. : 24.5-28.0 Power source for EUT: Manufacturer, model/type, output rating . : -- Component No. Fault Condition Fuse no. Fuse current, (A) Empty battery charge and working normally: C3 SC 5.
Page 46 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict DC motor Locked 5.0Vdc 7hrs10mi -ns -- -- -- Unit worked as normally. After test, no damaged, no hazard. No significant temperature change Battery OC 5.0Vdc 7hrs20mi -ns -- -- -- Max continuous charging current was 0.165A. The product worked as normal. No chemicals leak, explosion, molten metal emission or expulsion observed. Battery discharge: R3 SC 4.
Page 47 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Battery ED 4.35Vdc 7hrs Result - Remark -- -- -- Verdict -- Max continuous discharging current was 0.155A. The product worked as normal. No chemicals leak, explosion, molten metal emission or expulsion observed. (B-~P- SC) Supplementary information: SC: short circuit; ; OC: over charge; ED: excessive discharge. Annex M.
Page 48 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Result - Remark Verdict Annex M.4 Table: Additional safeguards for equipment containing secondary lithium batteries Battery/Cell No. P Measurements Test conditions Observation U I (A) Temp (°C) Normal 4.35 0.150 34.3 No fire or explosion (other than venting) of secondary lithium battery shall occur. Abnormal -- -- -- -- Single fault – B-~PSC 4.35 0.165 35.
Page 49 of 57 Report No.: LCS210301192AS IEC 62368-1 Clause Requirement + Test Enclosure Plastic Min. 1.5 Result - Remark 100N Verdict No damage, no hazardous 5 Supplementary information: T.6, T.9 TABLE: Impact tests N/A Part/Location Material Thickness (mm) Vertical distance (mm) Observation -- -- -- -- -- Supplementary information: T.7 TABLE: Drop tests P Part/Location Material Thickness (mm) Drop Height (mm) Observation Enclosure Plastic Min. 1.
Page 50 of 57 Report No.: LCS210301192AS Attachment No. 1 IEC62368_1D ATTACHMENT Clause Requirement + Test Result - Remark Verdict ATTACHMENT TO TEST REPORT IEC 62368-1 U.S.A. AND CANADA NATIONAL DIFFERENCES (Audio/video, information and communication technology equipment – Part 1: Safety requirements) Differences according to ................: CSA/UL 62368-1:2014 TRF template used: ....................... : IECEE OD-2020-F3, Ed. 1.1 Attachment Form No. .....................
Page 51 of 57 Report No.: LCS210301192AS Attachment No. 1 IEC62368_1D ATTACHMENT Clause Requirement + Test Result - Remark Verdict as required by Table G.7ADV.1 for cord connected equipment, or Annex DVH for permanently connected equipment 5.7.7 Equipment intended to receive telecommunication ringing signals complies with a special touch current measurement tests. N/A 6.5.1 PS3 wiring outside a fire enclosure complies with single fault testing in B.
Page 52 of 57 Report No.: LCS210301192AS Attachment No. 1 IEC62368_1D ATTACHMENT Clause Requirement + Test Result - Remark Verdict For ITE room applications, automated information storage systems with combustible 3 media greater than 0.76 m (27 cu ft) have a provision for connection of either automatic sprinklers or a gaseous agent extinguishing system with an extended discharge.
Page 53 of 57 Report No.: LCS210301192AS Attachment No. 1 IEC62368_1D ATTACHMENT Clause Requirement + Test Annex DVA (G.3.4) Suitable NEC/CEC branch circuit protection rated at the maximum circuit rating is required for all standard supply outlets and receptacles (such as supplied in power distribution units) if the supply branch circuit protection is not suitable. N/A Annex DVA (G.4.2) Equipment with isolated ground (earthing) receptacles complies with NEC 250.146(D) and CEC 10-112 and 10-906(8).
Page 54 of 57 Report No.: LCS210301192AS Attachment No.
Page 55 of 57 Report No.: LCS210301192AS Attachment No. 2 Details of: External View-1 Details of: External View-2 TRF No. IEC62368_1D Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-8259 1330 | Fax:+(86) 0755-8259 1332 | E-mail:webmaster@lcs-cert.com | http:// www.lcs-cert.
Page 56 of 57 Report No.: LCS210301192AS Attachment No. 2 Details of: External View-3 Details of: Internal View-1 TRF No. IEC62368_1D Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-8259 1330 | Fax:+(86) 0755-8259 1332 | E-mail:webmaster@lcs-cert.com | http:// www.lcs-cert.
Page 57 of 57 Report No.: LCS210301192AS Attachment No. 2 Details of: PCB View-1 Details of: PCB View-2 --------------------END OF TEST REPORT-------------------TRF No. IEC62368_1D Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-8259 1330 | Fax:+(86) 0755-8259 1332 | E-mail:webmaster@lcs-cert.com | http:// www.lcs-cert.