Wireless-G ADSL Home Gateway Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Wireless-G ADSL Home Gateway Table of Contents Chapter 1: Introduction 1 Welcome What’s in this User Guide? 1 2 Chapter 2: Planning Your Network 4 The Gateway’s Functions IP Addresses Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway Ports and Reset Button on Side Panel LEDs on Side Panel The Top Panel The Bottom Panel Chapter 4: Connecting the Wireless-G ADSL Home Gateway Overview Wired Connection to a Computer Wireless Connection to a Computer Chapter 5: Configuring the Wireless-G ADSL
Wireless-G ADSL Home Gateway Appendix C: Finding the MAC Address and IP Address for Your Ethernet Adapter Windows 98 or Me Instructions Windows 2000 or XP Instructions Appendix D: Upgrading Firmware Appendix E: Glossary Appendix F: Regulatory Information Appendix G: Warranty Information Appendix H: Specifications Appendix I: Contact Information 65 65 66 67 68 75 80 81 83
Wireless-G ADSL Home Gateway List of Figures Figure 2-1: Network Figure 3-1: Ports and Reset Button on Side Panel Figure 3-2: LEDs on Side Panel Figure 3-3: Top Panel Figure 3-4: Top Panel with Optional Antenna Figure 3-5: Bottom Panel with Stand in Closed Position Figure 3-6: Gateway Using Stand Figure 4-1: Connect the ADSL Line Figure 4-2: Connect a PC Figure 4-3: Connect the Power Figure 4-4: Connect the ADSL Line Figure 4-5: Connect the Power Figure 5-1: Login Screen Figure 5-2: Basic Setup Figure 5-3:
Wireless-G ADSL Home Gateway Figure 5-21: Security Figure 5-22: Firewall Log Figure 5-23: Internet Access Figure 5-24: Internet Policy Summary Figure 5-25: List of PCs Figure 5-26: Add/Edit Service Figure 5-27: Single Port Forwarding Figure 5-28: Port Range Forwarding Figure 5-29: Port Triggering Figure 5-30: DMZ Figure 5-31: QoS Figure 5-32: Management Figure 5-33: Allowed IP - IP Range Figure 5-34: Reporting Figure 5-35: System Log Figure 5-36: Ping Test Figure 5-37: Backup&Restore Figure 5-38: Factory D
Wireless-G ADSL Home Gateway Chapter 1: Introduction Welcome Thank you for choosing the Wireless-G ADSL Home Gateway. This Gateway will provide your computers with a high-speed Internet connection as well as resources, including files and printers. Since the Gateway is wireless, Internet access can be shared over the wired network as well as the wireless broadcast at up to 11Mbps for Wireless-B or up to 54Mbps for Wireless-G.
Wireless-G ADSL Home Gateway What’s in this User Guide? This user guide covers the steps for setting up and using the Wireless-G ADSL Home Gateway. • Chapter 1: Introduction This chapter describes applications of the Wireless-G ADSL Home Gateway and this User Guide. • Chapter 2: Planning Your Network This chapter describes the basics of networking. • Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway This chapter describes the physical features of the Gateway.
Wireless-G ADSL Home Gateway • Appendix H: Regulatory Information This appendix supplies the regulatory information regarding the Gateway. • Appendix I: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Wireless-G ADSL Home Gateway Chapter 2: Planning Your Network The Gateway’s Functions A Gateway is a network device that connects two networks together. In this instance, the Gateway connects your Local Area Network (LAN), or the group of computers in your home or office, to the Internet. The Gateway processes and regulates the data that travels between these two networks. The Gateway’s NAT feature protects your network of computers so users on the public, Internet side cannot “see” your computers.
Wireless-G ADSL Home Gateway Since you use the Gateway to share your DSL Internet connection, contact your ISP to find out if they have assigned a static IP address to your account. If so, you will need that static IP address when configuring the Gateway. You can get that information from your ISP. Dynamic IP Addresses A dynamic IP address is automatically assigned to a device on the network, such as computers and print servers.
Wireless-G ADSL Home Gateway Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway Ports and Reset Button on Side Panel The Gateway’s ports and Reset button are located on a side panel. Figure 3-1: Ports and Reset Button on Side Panel Line The Line port connects to the ADSL line. Ethernet (1-4) The Ethernet ports connect to your computers and other network devices. Reset Button There are two ways to reset the Gateway's factory defaults.
Wireless-G ADSL Home Gateway LEDs on Side Panel The Gateway's LEDs, which indicate network activity, are located on the other side panel. Figure 3-2: LEDs on Side Panel POWER Green. The POWER LED lights up when the Gateway is powered on. WIRELESS Green. The WIRELESS LED lights up whenever there is a successful wireless connection. If the LED is flashing, the Gateway is actively sending or receiving data to or from one of the devices on the network. ETHERNET (1-4) Green.
Wireless-G ADSL Home Gateway Chapter 4: Connecting the Wireless-G ADSL Home Gateway Overview The installation technician from your ISP should have left the setup information for the modem with you after installing your broadband connection. If not, you can call your ISP to request that data. After you have the setup information you need for your specific type of Internet connection, you can begin installation and setup of the Gateway.
Wireless-G ADSL Home Gateway Chapter 4: Connecting the Wireless-G ADSL Home Gateway Overview The installation technician from your ISP should have left the setup information for the modem with you after installing your broadband connection. If not, you can call your ISP to request that data. After you have the setup information you need for your specific type of Internet connection, you can begin installation and setup of the Gateway.
Wireless-G ADSL Home Gateway Wired Connection to a Computer 1. Make sure that all of your network’s hardware is powered off, including the Gateway and all computers. 2. Connect a phone cable from the Line port on the Gateway’s side panel to the wall jack of the ADSL line. A small device called a microfilter (not included) may be necessary between each phone and wall jack to prevent interference. Contact your ISP if you have any questions.
Wireless-G ADSL Home Gateway Wireless Connection to a Computer If you want to use a wireless connection to access the Gateway, follow these instructions: 1. Make sure that all of your network’s hardware is powered off, including the Gateway and all computers. 2. Connect a phone cable from the Line port on the Gateway’s back panel to the wall jack of the ADSL line. A small device called a microfilter (not included) may be necessary between each phone and wall jack to prevent interference.
Wireless-G ADSL Home Gateway Chapter 5: Configuring the Wireless-G ADSL Home Gateway Overview Follow the steps in this chapter and use the Gateway’s web-based utility to configure the Gateway. This chapter will describe each web page in the Utility and each page’s key functions. The utility can be accessed via your web browser through use of a computer connected to the Gateway. For a basic network setup, most users only have to use the following screens of the Utility: • Basic Setup.
Wireless-G ADSL Home Gateway Security On this screen you can disable or enable the firewall, set up filters, block WAN requests, and enable or disable Virtual Private Networks (VPN) PassThrough. Access Restrictions vpn (virtual private network): a security measure to protect data as it leaves one network and goes to another over the Internet. • Internet Access. This screen allows you to control the Internet usage and traffic on your local network. Applications & Gaming • Single Port Forwarding.
Wireless-G ADSL Home Gateway Status • Gateway. This screen provides status information about the Gateway. • Local Network. This provides status information about the local network. • Wireless. This screen provides status information about the wireless network. • DSL Connection. This screen provides status information about the DSL connection.
Wireless-G ADSL Home Gateway • Pcr Rate: For the Peak Cell Rate, divide the DSL line rate by 424 to get the maximum rate the sender can send cells. Enter the rate in the field (if required by your service provider). • Scr Rate: The Sustain Cell Rate sets the average cell rate that can be transmitted. The SCR value is normally less than the PCR value. Enter the rate in the field (if required by your service provider).
Wireless-G ADSL Home Gateway RFC 1483 Routed If you are required to use RFC 1483 Routed, then select RFC 1483 Routed. • Internet IP Address. This is the Gateway’s IP address, when seen from the WAN, or the Internet. Your ISP will provide you with the IP Address you need to specify here. • Subnet Mask. This is the Gateway’s Subnet Mask. Your ISP will provide you with the Subnet Mask. • Gateway. Your ISP will provide you with the default Gateway Address, which is the ISP server’s IP address.
Wireless-G ADSL Home Gateway RFC 2364 PPPoA Some DSL-based ISPs use PPPoA (Point-to-Point Protocol over ATM) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoA. If they do, you will have to enable PPPoA. • User Name and Password. Enter the User Name and Password provided by your ISP. • Connect on Demand: Max Idle Time.
Wireless-G ADSL Home Gateway • Local IP Address. The default value is 192.168.1.1. • Subnet Mask. The default value is 255.255.255.0. • Network Address Server Settings (DHCP). Configure the Gateway’s Dynamic Host Configuration Protocol (DHCP) settings in this section. • Local DHCP Server. A Dynamic Host Configuration Protocol (DHCP) server automatically assigns an IP address to each computer on your network for you.
Wireless-G ADSL Home Gateway The DDNS Tab The Gateway offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Gateway. Before you can use this feature, you need to sign up for DDNS service at DynDNS.org or TZO.com. DDNS DDNS Service. If your DDNS service is provided by DynDNS.org, then select DynDNS.org from the drop-down menu.
Wireless-G ADSL Home Gateway The Advanced Routing Tab The Advanced Routing screen allows you to configure the NAT, dynamic routing, and static routing settings. Advanced Routing • Operating Mode. In this section, you will configure the Gateway’s general routing settings. • NAT. NAT is a security feature that is enabled by default. It enables the Gateway to translate IP addresses of your local area network to a different IP address for the Internet. To disable NAT, click the Disabled radio button. • RIP.
Wireless-G ADSL Home Gateway • Select set number. Select the number of the static route from the drop-down menu. The Gateway supports up to 20 static route entries. If you need to delete a route, then select the entry and click the Delete This Entry button. • Destination IP Address. The Destination IP Address is the address of the remote network or host to which you want to assign a static route. Enter the IP address of the host for which you wish to create a static route.
Wireless-G ADSL Home Gateway The Wireless Tab The Basic Wireless Settings Tab This screen allows you to choose your wireless network mode and wireless security. Wireless Network • Wireless Network Mode. If you have 802.11g and 802.11b devices in your network, then keep the default setting, Mixed. If you have only 802.11g devices, select 802.11g. If you have only 802.11b devices, select 802.11b. If you want to disable wireless networking, select Disabled.
Wireless-G ADSL Home Gateway The Wireless Security Tab The Wireless Security settings configure the security of your wireless network. There are two wireless security options supported by the Gateway: WPA Personal and WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption. WEP stands for Wired Equivalent Privacy.) These are briefly discussed here.
Wireless-G ADSL Home Gateway WEP. WEP is a basic encryption method, which is not as secure as WPA. To use WEP, select a Default Key (this indicates which Key to use) and a level of WEP encryption, 64 bits 10 hex digits or 128 bits 26 hex digits. Then either generate a WEP key using a Passphrase or enter the WEP key manually. • WEP Encryption. An acronym for Wired Equivalent Privacy, WEP is an encryption method used to protect your wireless data communications.
Wireless-G ADSL Home Gateway The Wireless Access Tab Wireless Network Access Wireless Network Access. Select Allow All you want all computers to have access to the wireless network. To restrict access to the network, select Restrict Access, and then select Prevent to block access for the designated computers or Permit only to permit access for the designated computers. Click the Edit MAC Address Access List button, and the Mac Address Filter List screen will appear.
Wireless-G ADSL Home Gateway The Advanced Wireless Settings Tab Advanced Wireless On this screen you can access the advanced wireless features, including Authentication Type, Control TX Rate, Beacon Interval, DTIM Interval, Fragmentation Threshold, and RTS Threshold. • Authentication Type. The default is set to Auto, which allows either Open System or Shared Key authentication to be used.
Wireless-G ADSL Home Gateway The Security Tab This screen shows the VPN passthrough, firewall, and filter settings. Use these features to enhance the security of your network. VPN Passthrough Virtual Private Networking (VPN) is a security measure that basically creates a secure connection between two remote locations. Configure these settings so the Gateway will permit VPN tunnels to pass through. • IPSec Passthrough.
Wireless-G ADSL Home Gateway • Filter Java Applets. Java is a programming language for websites. If you deny Java Applets, you run the risk of not having access to Internet sites created using this programming language. To enable Java Applet filtering, click the checkbox. • Filter ActiveX. ActiveX is a programming language for websites. If you deny ActiveX, you run the risk of not having access to Internet sites created using this programming language. To enable ActiveX filtering, click the checkbox.
Wireless-G ADSL Home Gateway The Access Restrictions Tab The Internet Access Tab The Internet Access screen allows you to block or allow specific kinds of Internet usage. You can set up Internet access policies for specific computers and block websites by URL address or keyword. Internet Access Policy. Access can be managed by a policy. Use the settings on this screen to establish an access policy (after the Save Settings button is clicked).
Wireless-G ADSL Home Gateway 4. Click the Edit List of PCs button to select which PCs will be affected by the policy. The List of PCs screen will appear. You can select a PC by MAC Address or IP Address. You can also enter a range of IP Addresses if you want this policy to affect a group of PCs. After making your changes, click the Save Settings button to apply your changes or Cancel Changes to cancel your changes. 5.
Wireless-G ADSL Home Gateway The Applications and Gaming Tab The Single Port Forwarding Tab Single Port Forwarding Use the Single Port Forwarding screen when you want to open a specific port so users on the Internet can see the servers behind the Gateway (such servers may include FTP or e-mail servers). When users send this type of request to your network via the Internet, the Gateway will forward those requests to the appropriate computer.
Wireless-G ADSL Home Gateway The Port Range Forwarding Tab The Port Range Forwarding screen sets up public services on your network, such as web servers, ftp servers, email servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.
Wireless-G ADSL Home Gateway The Port Triggering Tab Port Triggering is used for special applications that can request a port to be opened on demand. For this feature, the Gateway will watch outgoing data for specific port numbers. The Gateway will remember the IP address of the computer that sends a transmission requesting data, so that when the requested data returns through the Gateway, the data is pulled back to the proper computer by way of IP address and port mapping rules. • Application.
Wireless-G ADSL Home Gateway The DMZ Tab The DMZ screen allows one local user to be exposed to the Internet for use of a special-purpose service such as Internet gaming and videoconferencing through DMZ Hosting. DMZ hosting forwards all the ports for one computer at the same time, which differs from Port Range Forwarding, which can only forward a maximum of 10 ranges of ports. • DMZ Hosting.
Wireless-G ADSL Home Gateway The QoS Tab QoS Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as Internet phone calls or videoconferencing. Enabled/Disabled. To use QoS, select Enable. Otherwise, keep the default, Disable. Application-based QoS Application-based QoS manages information as it is transmitted and received.
Wireless-G ADSL Home Gateway SNMP SNMP is a popular network monitoring and management protocol. To enable SNMP, click Enabled. To disable SNMP, click Disabled. If enabled, then specify the IP address(es) allowed to have SNMP access. Select All to allow all IP addresses with no restrictions, IP address to specify a single IP address, or IP range to specify a range of IP addresses. • Device Name. Enter the name of the Gateway. • SNMP v1/v2: Get Community.
Wireless-G ADSL Home Gateway The Reporting Tab The Reporting screen provides you with a log of all incoming and outgoing URLs or IP addresses for your Internet connection. It also provides logs for VPN and firewall events. Reporting • Log. To enable log reporting, click Enabled. • Logviewer IP Address. Enter the IP Address of the computer that will receive logs. You will need Logviewer software to view these logs. This free software is available for download from www.linksys.com.
Wireless-G ADSL Home Gateway The Administration Tab The Management Tab The Management screen allows you to change the Gateway’s access settings as well as configure the SNMP (Simple Network Management Protocol), UPnP (Universal Plug and Play), IGMP (Internet Group Multicast Protocol)-Proxy, and WLAN management features. Gateway Access Local Gateway Access. To ensure the Gateway’s security, you will be asked for your password when you access the Gateway’s Web-based Utility.
Wireless-G ADSL Home Gateway The Diagnostics Tab Ping Test Ping Test Parameters • Ping Target IP. Enter the IP address that you want to ping. This can be either a local (LAN) IP or an Internet (WAN) IP address. • Ping Size. Enter the size of the packet. • Number of Pings. Enter the number of times that you want to ping. • Ping Interval. Enter the ping interval (how often the target IP address will be pinged) in milliseconds. Figure 5-36: Ping Test • Ping Timeout.
Wireless-G ADSL Home Gateway The Factory Defaults Tab Restore Factory Defaults. If you wish to restore the Gateway to its factory default settings and lose all your settings, click Yes. To begin the restore process, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes. The Firmware Upgrade Tab Figure 5-38: Factory Defaults The Gateway allows you to upgrade firmware from the LAN (Local Area Network) side of the Gateway.
Wireless-G ADSL Home Gateway The Reboot Tab This screen allows you to do a soft or hard reboot of the Gateway. In most cases you should use the hard reboot. The soft reboot is similar to restarting your computer without physically powering down the computer. Reboot Reboot Mode. To reboot your Gateway, select Hard or Soft. Choose Hard to power cycle the Gateway or Soft. to restart it without a power cycle. Figure 5-40: Reboot To begin the reboot process, click the Save Settings button.
Wireless-G ADSL Home Gateway The Status Tab The Gateway Tab This screen displays information about the Gateway and its Internet connection. Gateway Information This section displays the Gateway’s Firmware Version, MAC Address, and Current Time. Internet Connection This section shows the following information: the Connection, Login Type, Interface, IP Address, Subnet Mask, Default Gateway, DNS 1, 2, and 3 server IP addresses, and WINS address. DHCP Renew.
Wireless-G ADSL Home Gateway The Local Network Tab The Local Network information that is displayed is the local Mac Address, IP Address, Subnet Mask, DHCP Server, Start IP Address, and End IP Address. To view the DHCP Clients Table, click the DHCP Clients Table button. To view the ARP/RARP Table, click the ARP/RARP Table button. DHCP Clients Table. The DHCP Active IP Table shows the current DHCP Client data.
Wireless-G ADSL Home Gateway The Wireless Tab The Wireless network information that is displayed is the Wireless Firmware Version, MAC Address, Mode, SSID, DHCP Server, Channel, and Encryption Function. Click the Wireless Clients Connected button to view a list of the wireless clients connected to the Gateway, along with their computer names, IP addresses, and MAC addresses. Click the Refresh button if you want to refresh the displayed information. Click the Close button to return to the Wireless screen.
Wireless-G ADSL Home Gateway The DSL Connection Tab This screen shows information about the DSL connection and the PVC connection. DSL Status This section shows the following: DSL Status, DSL Modulation Mode, DSL Path Mode, Downstream Rate, Upstream Rate, Downstream Margin, Upstream Margin, Downstream Line Attenuation, Upstream Line Attenuation, Downstream Transmit Power, and Upstream Transmit Power.
Wireless-G ADSL Home Gateway Appendix A: Troubleshooting This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” Provided are possible solutions to problems that may occur during the installation and operation of the Gateway. Read the descriptions below to help you solve your problems. If you can’t find an answer here, check the Linksys international website at www.linksys.com/international. Common Problems and Solutions 1.
Wireless-G ADSL Home Gateway 7. Toward the bottom of the window, select Use the following DNS server addresses, and enter the Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its website to find the information. 8. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. 9. Restart the computer if asked.
Wireless-G ADSL Home Gateway For Windows 98 and Me: • Click Start and Run. In the Open field, type in command. Press the Enter key or click the OK button. For Windows NT, 2000, and XP: • Click Start and Run. In the Open field, type cmd. Press the Enter key or click the OK button. In the command prompt, type ping 192.168.1.1 and press the Enter key. • If you get a reply, the computer is communicating with the Gateway.
Wireless-G ADSL Home Gateway 3. Refer to “Problem #10: I am a PPPoE user, and I need to remove the proxy settings or the dial-up popup window.” 5. I can’t get my Virtual Private Network (VPN) working through the Gateway. Access the Gateway’s web interface by going to http://192.168.1.1 or the IP address of the Gateway, and go to the Security tab. Make sure you have IPsec passthrough and/or PPTP pass-through enabled.
Wireless-G ADSL Home Gateway field provided. Check “Appendix C: Finding the MAC Address and IP Address for Your Ethernet Adapter” for details on getting an IP address. 6. Check the Enable option for the port services you want to use. Consider the example below: Customized Application Web server FTP server SMTP (outgoing) POP3 (incoming) External Port 80 to 80 21 to 21 25 to 25 110 to 110 TCP X X X X UDP IP Address 192.168.1.100 192.168.1.101 192.168.1.102 192.168.1.
Wireless-G ADSL Home Gateway 8. I can’t get the Internet game, server, or application to work. If you are having difficulties getting any Internet game, server, or application to function properly, consider exposing one computer to the Internet using DeMilitarized Zone (DMZ) hosting. This option is available when an application requires too many ports or when you are not sure which port services to use.
Wireless-G ADSL Home Gateway • For Netscape 6 or higher: 1. Start Netscape Navigator, and click Edit, Preferences, Advanced, and Proxies. 2. Make sure you have Direct connection to the Internet selected on this screen. 3. Close all the windows to finish. 11. To start over, I need to set the Gateway to factory default. Hold the Reset button for 10 seconds and then release it. This will return the Internet settings, password, forwarding, and other settings on the Gateway to the factory default settings.
Wireless-G ADSL Home Gateway 1. To connect to the Gateway, go to the web browser, and enter http://192.168.1.1 or the IP address of the Gateway. 2. Enter the username and password, if asked. (The default username and password is admin.) 3. On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds). 4. Click the Save Settings button. Click the Status tab, and click the Connect button. 5. You may see the login status display as Connecting.
Wireless-G ADSL Home Gateway • If the Gateway is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is working correctly. You can remove the Gateway to verify a direct connection. • Manually configure the TCP/IP settings with a DNS address provided by your ISP. • Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet Explorer, click Tools, Internet Options, and then the Connection tab.
Wireless-G ADSL Home Gateway What is Network Address Translation and what is it used for? Network Address Translation (NAT) translates multiple IP addresses on the private LAN to one public address that is sent out to the Internet. This adds a level of security since the address of a computer connected to the private LAN is never transmitted on the Internet. Furthermore, NAT allows the Gateway to be used with low cost Internet accounts when only one TCP/IP address is provided by the ISP.
Wireless-G ADSL Home Gateway The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the screen. What do I need to do? Force your Ethernet adapter to 10Mbps or half duplex mode, and turn off the “Auto-negotiate” feature of your Ethernet adapter as a temporary measure. (Please look at the Network Control Panel in your Ethernet adapter’s Advanced Properties tab.) Make sure that your proxy setting is disabled in the browser. Check our website at www.linksys.
Wireless-G ADSL Home Gateway Is the Gateway cross-platform compatible? Any platform that supports Ethernet and TCP/IP is compatible with the Gateway. How many ports can be simultaneously forwarded? Theoretically, the Gateway can establish 520 sessions at the same time, but you can only forward 10 ranges of ports. What are the advanced features of the Gateway? The Gateway’s advanced features include Advanced Wireless settings, Filters, Port Forwarding, Routing, and DDNS.
Wireless-G ADSL Home Gateway What IEEE 802.11b and 802.11g features are supported? The product supports the following IEEE 802.11b and IEEE 802.11g functions: • CSMA/CA plus Acknowledge protocol • Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation • Power Management It also supports OFDM technology for 802.11g networking.
Wireless-G ADSL Home Gateway What is the ISM band? The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe.
Wireless-G ADSL Home Gateway How do I reset the Gateway? Press the Reset button on the back panel for about ten seconds. This will reset the Gateway to its default settings. How do I resolve issues with signal loss? There is no way to know the exact range of your wireless network without testing. Every obstacle placed between the Gateway and a wireless computer will create signal loss. Lead glass, metal, concrete floors, water and walls will inhibit the signal and reduce range.
Wireless-G ADSL Home Gateway Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.
Wireless-G ADSL Home Gateway SSID. There are several things to keep in mind about the SSID: 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.
Wireless-G ADSL Home Gateway WPA Pre-Shared Key. If you do not have a RADIUS server, Select the type of algorithm, TKIP or AES, enter a password in the Pre-Shared key field of 8-64 characters, and enter a Group Key Renewal period time between 0 and 99,999 seconds, which instructs the Gateway or other device how often it should change the encryption keys. WPA RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Gateway or other device.
Wireless-G ADSL Home Gateway Appendix C: Finding the MAC Address and IP Address for Your Ethernet Adapter This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC filtering feature of the Gateway. You can also find the IP address of your computer’s Ethernet adapter. This IP address is used for the Gateway’s filtering, forwarding, and/or DMZ features.
Wireless-G ADSL Home Gateway Windows 2000 or XP Instructions 1. Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button. Note: The MAC address is also called the Physical Address. 2. At the command prompt, enter ipconfig /all. Then press the Enter key. 3. Write down the Physical Address as shown on your computer screen (Figure C-3); it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters.
Wireless-G ADSL Home Gateway Appendix D: Upgrading Firmware To upgrade the Gateway’s firmware: 1. Download the Gateway’s firmware upgrade file from www.linksys.com. 2. Extract the file on your computer. 3. Open the Gateway’s Web-based Utility and click the Administration tab. 4. Click the Firmware Upgrade tab. 5. Click the Browse button to find the extracted file, and then double-click it. 6. Click the Upgrade button, and follow the on-screen instructions.
Wireless-G ADSL Home Gateway Appendix E: Glossary 802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. 802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices. Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network.
Wireless-G ADSL Home Gateway Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet. CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent data collisions. CTS (Clear To Send) - A signal sent by a wireless device, signifying that it is ready to receive data. Daisy Chain - A method used to connect devices in a series, one after the other.
Wireless-G ADSL Home Gateway EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access. Many specific authentication methods work within this framework. EAP-PEAP (Extensible Authentication Protocol-Protected Extensible Authentication Protocol) - A mutual authentication method that uses a combination of digital certificates and another system, such as passwords.
Wireless-G ADSL Home Gateway IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer. ISM band - Radio bandwidth utilized in wireless transmissions. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network.
Wireless-G ADSL Home Gateway Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online. POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet. Port - The connection point on a computer or networking device used for plugging in cables or adapters. Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.
Wireless-G ADSL Home Gateway Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission. SSID (Service Set IDentifier) - Your wireless network's name. Static IP Address - A fixed address assigned to a computer or device that is connected to a network. Static Routing - Forwarding data in a network via a fixed path. Subnet Mask - An address code that determines the size of the network. Switch - 1.
Wireless-G ADSL Home Gateway VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another over the Internet. WAN (Wide Area Network)- The Internet. WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security. WINIPCFG - A Windows 98 and Me utility that displays the IP address for a particular networking device.
Wireless-G ADSL Home Gateway Appendix F: Regulatory Information Compliance Information for 2.4-GHz Wireless Products Relevant to the EU and Other Countries Following the EU Directive 1999/5/EC (R&TTE Directive) Declaration of Conformity with Regard to the EU Directive 1995/5/EC (R&TTE Directive) NOTE: For all products, the Declaration of Conformity is available through one or more of these options: • A pdf file is included on the product's CD. • A print copy is included with the product.
Wireless-G ADSL Home Gateway National Restrictions This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour les pays mentionnés ci-dessous: Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le diretti
Wireless-G ADSL Home Gateway France In case the product is used outdoors, the output power is restricted in some parts of the band. See Table 1 or check http://www.art-telecom.fr/ for more details. Dans la cas d’une utilisation en extérieur, la puissance de sortie est limitée pour certaines parties de la bande. Reportezvous à la table 1 ou visitez http://www.art-telecom.fr/ pour de plus amples détails.
Wireless-G ADSL Home Gateway Power Output of Your Device To comply with your country’s regulations, you may have to change the power output of your wireless device. Proceed to the appropriate section for your device. Note: The power output setting may not be available on all wireless products. For more information, refer to the documentation on your product’s CD or http://www.linksys.com/international. Wireless Adapters Wireless adapters have the power output set to 100% by default.
Wireless-G ADSL Home Gateway Technical Documents on www.linksys.com/international Follow these steps to access technical documents: 1. Browse to http://www.linksys.com/international. 2. Click the region in which you reside. 3. Click the name of the country in which you reside. 4. Click Products. 5. Click the appropriate product category. 6. Select a product. 7. Click the type of documentation you want. The document will automatically open in PDF format.
Wireless-G ADSL Home Gateway Appendix G: Warranty Information Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser.
Wireless-G ADSL Home Gateway Appendix H: Specifications Model Number WAG200G Standards IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, G.992.1 (G.dmt), G.992.2 (G.lite), G.992.3, G.992.5, T1.413i2 Ports Power, ADSL, Ethernet (1-4) Button One Reset Button Cabling Type CAT 5 UTP LEDs Power, Wireless, Ethernet (1-4), DSL, Internet Transmit Power 802.11b:17.5dBm 802.11g: 16.
Wireless-G ADSL Home Gateway Dimensions 140 mm x 140 mm x 27 mm (5,51" x 5,51" x 1,06") Unit Weight 0,3 kg (0,6 lb.) Power 12VDC 1A Certifications CE Operating Temp. 0º~40ºC (32º~104ºF) Storage Temp.
Wireless-G ADSL Home Gateway Appendix I: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com/international If you experience problems with any Linksys product, you can e-mail us at: In Europe E-mail Address Austria support.at@linksys.com Belgium support.be@linksys.com Denmark support.dk@linksys.com France support.fr@linksys.com Germany support.de@linksys.com Italy support.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Th is equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.