Side by Side Installation CS CS HC HC HCB HCB 2061 2081 2061 2081 2061 2081 + + + + + + CS 2060 CS 2080 HC 2060 HC 2080 HCB 2060 HCB 2080 7082 023-00
Parts list of SBS Installation Kit Image Article number Name of the item 6943 651-00 Heating blanket 9041 321-00 Guide plate 7745 045-00 Angle bracket 9190 201-00 Top cover 2
Image Article number Name of the item 7641 503-00 Sealing strip 4084 005-01 Metric screws M 6 x 13 7082 023-00 Installation manual Other parts used in this installation manual are supplied with the appliance, not with the SBS Kit.
Side by Side (SBS) Installation WARNING! WARNING! Risk of fire or damage. Electrocution hazard. The accessory is intended for use only with a refrigerator that is marked to indicate such use. The refrigerator must be disconnected from the source of electrical supply before attempting the installation.
Note Step 5 is for HC (fully integrated) appliances only. 5. 5. Remove the inner supports. 6. 6. Loosen the protective foil of the heating blanekt top. Pull down the foil for approx. 4". Important Do not remove the protective foil completely. 7. 7. Adhere the heating blanekt on the top of the left unit. Upper edge of blanekt 4-1/2" from the appliance top. Front edge of blanekt 1-1/2" from the appliance housing backwards.
8. Bend the lower tongue of the heating blanekt around the corner and adhere to the back of the appliance. note Heating blanket only has 17 W, so no heat can be felt after installation. 8. 9. Connect the cable of the heating blanekt with the socket in the compressor compartment. Important Make sure, that the heater cable is not laying on the floor. Please put the cable inside the compressor compartment. 9.
Note Step 11 is for HC (fully integrated) appliances only. 11. Apply cover strips above, between and below the securing plates on the left side wall of the left appliance and on the right side wall of the right appliance. 11. 11. Cut the cover strips to the length as shown in Step 11 using a pair of heavy duty scissors or a utility knife. Adhere the cover strips leaving a gap of 1/4" to each securing plate to prevent interference when installing the covers. 12.
14. 13. Align both appliances. Refer to chapter Leveling the appliance in the installation instructions. IMPORTANT The appliances must be in line at the front and in height and must be aligned vertical. 13. 14. Open the doors and remove the screws. These screws are needed in the next step. 14. 15. Attach the angle bracket supplied with the SBS Kit and fasten with the screws of step 14 through the two center holes. 16.
17. Click the cover supplied with the SBS kit into place. 18. Open the doors and press the sealing strip supplied with the SBS kit into the gap at the front. 17. 18. Complete the Side by Side installation considering the following chapters in the installation instructions. 19. Connection to the water supply (from passage 5 - 9) 20. Fastening the appliance in the recess 21. Before mounting the door panels 22. Mounting the attachment brackets onto the door panels 23.
Notes 10
Notes 11
For Service in the U.S. Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Email: Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 www.liebherr-appliances.
