Owner's Manual

• W
ater supply is not adequate in area
• W
ater supply taps are not completely open.
•
Water inlet hose(s) are kinked.
•
The filter of the inlet hose(s) are clogged.
•
If water leakage occurred in the inlet hose,
indicator “ A ” will be changed red color.
• Drain hose is kinked or clogged.
• The drain filter is clogged.
• Load is too small
.
• Load is out of balance.
•
The appliance has an unbalance detection
and correction system. If individual heav
y
articles are loaded (ex. bath mat, both robe,
etc.), this system may stop spinning or even
interrupt the spin cycle altogether.
•
If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
• Is the door opened or no
t
completely closed?
•
Water overfills due to the faulty water
valve.
•
Water level sensor has malfunctioned.
• Over load in motor.
•
Water leaks
• The washer experienced a power failure.
Check another tap in the house.
Fully open tap.
Straighten hose(s)
.
Check the filter of the inlet hose(s)
.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information,
please refer to
“
Cleaning the drain pump filter
”
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning
Close the door completely
.
If “ ”is not released, call for service
.
Unplug the power plug and call for service.
Close the water tap.
Unplug the power plug.
Call for service
.
Call for service
.
Restart the cycle.
Fig1
29
arantiebedingungen
G
Unter die Garantie fallen nicht:
• Heimservice zur Einführung in die Benutzung des Geräts.
• Wenn das Gerät an eine Spannung angeschlossen ist, die nicht mit der auf dem
Nennleistungsschild angegebenen übereinstimmt.
• Wenn die Störung durch Unfälle, Vernachlässigung, Missbrauch oder höhere Gewalt
verursacht wird.
• Wenn die Störung durch unsachgemäße Benutzung des Geräts oder Nichtbeachtung
der Bedienungsanleitung verursacht wird.
• Die Gebrauchsanweisung für das Gerät zur Verfügung stellen oder die Einstellungen
des Geräts ändern.
• Wenn die Störung durch Schädlinge wie Ratten oder Kakerlaken etc. verursacht wird.
• Normale Geräusche oder Vibrationen z. B. das Geräusch von ablaufendem Wasser,
Drehgeräusche oder Pieptöne während der Erwärmung.
• Die Installation korrigieren, das Gerät nivellieren oder den Abfluss einstellen.
• Normale Wartung, wie sie im Benutzerhandbuch empfohlen wird.
• Entfernung von Fremdkörpern wie Sand, Nägeln, BH-Bügeln, Knöpfen etc. aus der
Maschine sowie aus der Pumpe und dem Einlassfilter.
•
Sicherungen ersetzen oder die elektrischen Anschlüsse oder Rohrleitungen korrigieren.
• Korrektur von unbefugten Reparaturen.
• Schäden an persönlichem Eigentum, die direkt oder indirekt durch Defekte dieses
Geräts verursacht werden.
•
Wenn dieses Gerät zu kommerziellen Zwecken benutzt wird, steht es nicht unter Garantie.
(Beispiel: öffentliche Orte wie Toiletten, Hotels, Fitness-Center, Pensionen)
Entsorgung von Altgeräten
1. Wenn dieses Symbol eines durchgestrichenen Abfalleimers
auf einem Produkt angebracht ist, unterliegt dieses Produkt
der europäischen Richtlinie 2002/96/EC.
2. Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom
Hausmüll über dafür staatlich vorgesehenen Stellen entsorgt
werden.
3. Mit der ordnungsgemäßen Entsorgung des alten Geräts
vermeiden Sie Umweltschäden und eine Gefährdung der
persönlichen Gesundheit.
4. Weitere Informationen zur Entsorgung des alten Geräts
erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt
oder in dem Geschäft, wo Sie das Produkt erworben haben.
4
1
2
3
5
7
5
3 . Die 4 Schrauben lösen und die
Gummipfropfen etwas drehen, um sie
zusammen mit den Schrauben abzunehmen.
Die 4 Schrauben und den Schraubenschlüssel
für späteren Gebrauch aufbewahren.
• Die Transportsicherungsschrauben müssen vor
jedem Transport des Geräts wieder angebracht
werden.
4 . Die Schraubenbohrungen mit den
beiliegenden Kappen verschließen.
1 2
3 4
Schraubenschlüssel
6
Adjustable fee
t
60 - 100 cm
@
N
Green and Yellow(Earth)
Brown(Live)
Blue(Neutral)
Fuse
Cord
grip
E
L
N
Name of product Front loading washing machine
Power supply 220-240 V~, 50 Hz
Size WxDxH mm: 600 x 590 x 850
Weight 63 kg
Max. Watt 2100 W (Wash) / 1100 W (Steam)
Wash capacity 8 kg
Water consumption 52 l (6.5l / kg)
Permissible water pressure 1.0-10 bar (100-1000kPa)
Owner‘s Manual
F1403TDS(1~9)
Safety instructions for use
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating
instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these
operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before instal-
ling the appliance and putting it into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only
with cold drinking water and only for washing textiles with washing detergents designed for washing machines. Every
other use is improper and may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualifi ed fi tter or technician.
• Have electrical connections done by a qualifi ed electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never
disconnect by pulling the power cord. Never touch the plug with wet fi ngers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or
parts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fi re.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized
customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive
substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fi re
or explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover
has been used then make sure that the solvent has been carefully washed out before inserting the clothes into the
appliance. Oil may remain in the tub after a whole cycle resulting in fi re during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where fl ammable substances are present such as oil, benzene or highly
infl ammable gas. Such materials may cause fi re or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of
scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement parts.
• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to
protect children.
• When placing on a carpeted fl oor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fi re.
• The cover cup of the fi lter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning
Disposal
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.
Remove Packaging
Requirements for installation site
Transit bolts
Electrical connection
Connecting water supply hose
• The appliance is fi tted with transit bolts to prevent internal
damage during transport. Be careful, heavy load!
• Packing and all transit bolts must be removed before using
the washing machine.
• When unpacking the base, be sure to remove the additional
packing support in the middle of the base packing.
Store original packing for future move.
Dispose of packing material according to local regulations.
Unscrew the 4 bolts
using the spanner
supplied.
Keep the 4 bolts and the spanner for the future use. Refi t transit bolts before transporting the appliance.
Level fl oor: Permissible fl oor gradient under entire washing machine
is 1˚ .
Power socket: Must be within 100 cm of either side of location of
washing machine. Do not overload the socket with more than one
appliance.
Additional Clearance: For wall, fl oor and door space is needed.
(10cm: rear / 2cm:right & left side). Do not place or store laundry pro-
ducts on top of the washing machine at any times. They can damage
the fi nish or controls of the machine.
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualifi ed person
to prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualifi ed personnel. Repairs carried out by inexpe-
rienced persons may cause injury or serious malfunctioning. Contact your local service centre.
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.
• Two rubber seals are supplied with the water inlet
hoses. They are used for preventing water leaks.
• Make sure the connection to taps is tight enough.
• Periodically check the condition of the hose and
replace the hose if necessary.
• Make sure that there is no kink on the hose and
that it is not crushed.
Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)
Don’t strip or crossthread when connecting inlet hose to the valve.
If the water supply pressure is more than 1000kPa, a decompression
device should be installed.
• The drain hose should not be placed higher than 100 cm above the fl oor.
• Proper securing of the drain hose will protect the fl oor from damage due to any water leakage.
• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.
• Proper level-adjustment of the washing ma-
chine prevents excessive noise and vibration.
Install the appliance on a solid and level fl oor
surface, preferably in a corner of the room.
• If the fl oor is uneven, adjust feet as required.
(Do not insert pieces of wood etc. under the
feet). Make sure that all four feet are stable
and resting on the fl oor. Then check that
the appliance is perfectly level. (Use a spirit
level).
Safety instuctions for the installation
Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the
washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted fl oor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION about positioning the appliance
Install the washing machine on a fl at hard fl oor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
• Never try to correct any unevenness in the fl oor using pieces of wood, cardboard or similar materials under the washing machine.
• If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
• The washing machine must not be installed in rooms where the temperature may drop below 0°C.
• Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.
• Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
CAUTION about the power cord
We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance
concerned, without any additional outlets or branch circuits. Check the specifi cations of this owner‘s manual. Do not overload
wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or
cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fi re. Periodically examine the
cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular atten-
tion to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated
device in the mains supply.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stop-
cock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no fl oor drain (gully)
in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young
children becoming trapped inside. Packaging material (e.g. plastic fi lm, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging well away from children.
CAUTION about the fl oor surface
• The installation surface must be clean, dry and level.
• Install washing machine on a fl at hard fl oor.
• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
• The washing machine must be perfectly level and fi rmly in position.
• It must not “see-saw” across corners under load.
• The installation surface must be clean, free from fl oor wax and other lubricant coatings.
• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound Heavy wash loads may produce a thumping sound. This is usually normal.
Vibrating noise Have all transit bolts and packing been removed?
Water leaks. Check and tighten hose connections. Unclog drain pipe.
Contact plumber if necessary.
Excessive suds Too much detergent or unsuitable detergent.
Washing machine does not start Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin Check that the door is fi rmly shut.
Door does not open Once started, the door can not be opened for safety reasons.
Wait one or two minutes before opening the door to allow the electric
locking mechanism time to release.
Troubleshooting
Level adjustment
To prevent internal dama-
ge during transport, the
special 4 bolts are locked.
If they are not removed, it
may cause heavy vibrati-
on, noise and machine to
malfunction.
Installation of drain hose
Technical Specifi cation
i
If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional
type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting
the tap into the adaptor.
i
i
• When this crossed-out wheeled bin symbol is attached to a product it means the product is covered
by European Directive 2002/96/EC.
• All electrical and electronic products should be disposed of separately from municipal waste stream
via designated collection facilities appointed by the government or the local authorities.
• The correct disposal of your old appliance will help prevent potential adverse consequences for the
environment and human health.
• For more detailed information about disposal of your old appliance, please contact your city offi ce,
waste disposal service or the shop where you purchased the product.
The hose supplied with the machine must be used. Old hoses may not be reused
Close the holes with
the caps supplied.
Remove the 4 bolts
along with the rubber
bungs by slightly
twisting the bung.
P/No. :MFL59755511