Install Manual Wall Mounting Bracket Please read this manual carefully before operating your set and retain it for future reference. OSW100 P/NO : MFL63640559 (1406-REV00) www.lg.
COMPONENT Rea Hee Install manual Wall mount anchor 6 units Wall mount screw 6 units * Component of top wall mount T a r H s c U m In o s Top wall mount (assembled with a mounting bracket for wooden walls) 2 spacers (front) Hanger 2 spacers (back) 1 pin for fixing top wall mount In d If d s 2 screws for attaching the hanger (M6 x L33 mm) D m s If s th is * Component of bottom wall mount 1 bottom-right wall mount 8 washers 2 1 bottom-left wall mount 2 bottom wall attaching brackets W p T
ng ENGLISH all IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Warning This wall mount should be installed by a trained and experienced installer designated by the retailer. Having the product installed by a nonspecialized installer is very dangerous and can cause damage or injury. Do not install the product where the weight cannot be supported.
2 BEFORE INSTALLATION * Do not use the product for purposes other than mounting a display on the wall. * When installing/using the wall mount, be cautious of product damage and avoid accidents. * If you have not fully read and understood the installation manual, do not install the product and contact the dealer to have a specialized installer install the product for you. * This product is designed to be mounted to walls that use standard intervals between the studs.
of ENGLISH act 2 How to Attach the Brackets for the Product to the TV -- If the screws are not fully tightened when you fix the top and the bottom wall mount, check the length of the screws and tighten them again. -- Always install the display with 2 or more people. -- Work procedure 1. Remove the two VESA screws from VESA Screw upper back of TV when in an upright position. gth e cs Hanger se el / Screw for attaching the hanger Stand Screw of Stand s e bottom wall mount Screw of Stand 2.
3 How to attach to masonry walls Please follow the below direction. -- Check the material of the wall and the thickness of the finishing. -- Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack. -- Do not mount the device on the walls made from plasterboard or medium density fiberboard (MDF). In this case, the anchor and screws must be inserted into the concrete behind the finish surface.
A A ). Remove the wall mount fixing screws. all n A A Wall mount screw When mounting to wooden studs art . →→Fix one wall mount fixing screw into the top left hole next to A and another screw into the top right hole next to A as shown in the illustration. →→At this time, use a + driver (Manual or motorized) or 8 mm wrench to tighten the screw so that the wall, wall bracket and screw are completely pressed against one another. →→After attaching the screws, put down the top of the top wall mount.
5 How to Install the Bottom Wall Mount How to Select the Installation Location of the Bottom Wall Mount [unit : mm] ➊ 541 ➋ ➌ 350 90˚ 350 ➍ ➊ Place the box on the bottom center of the attached top wall mount and place the box at a right angle (90 degrees) to the top wall mount as shown in the figure. ➋ Find the V on the bottom of your box, and mark the point facing it on the wall [(a) in the figure].
76 mm drywall mm] wood stud 406 mm Washer drywall bottom wall fixing washer bottom wall fixing bracket a. Locate and mark the centers of the wall studs using a stud finder. b. After aligning the wall bracket on the wall where the center of the wood stud is marked, mark the location of the screws and then remove the wall bracket. c. Use a level to make sure your screw marks are level. d.
Please follow the below direction. This product is easily damaged by external shock, so please handle it with care. For more information, please refer to the owner's manual of the TV. 7 How to Install the Top Wall Mount Fixing Pin pin for fixing top wall mount →→After installing the top wall mount, attach the wall mount to the TV using the top wall mount attaching pin as shown in the illustration.
[ unit : mm ] Hanger 238 99 3 7 8.5 210 18.5 Top wall mount ay 40 63 23.5 5 160 406 483 Bottom wall mount hat Width (mm) Height (mm) Depth (mm) Weight with packing (kg) Max.UL Load Capacity (kg) Top Assembly 483 63 23.5 Hanger Assembly 238 99 18.5 1.3 30 Lower Assembly 169.9 34.9 49.