User guide
APPENDIX
78
APPENDIX
01. Power k a 0 ~ 1
02. Input Select k b Refer to p. 79
03. Aspect Ratio k c Refer to p. 79
04. Screen Mute k d 0 ~ 1
05. Volume Mute k e 0 ~ 1
06. Volume Control k f 0 ~ 64
07. Contrast k g 0 ~ 64
08. Brightness k h 0 ~ 64
09. Colour k i 0 ~ 64
10. Tint (option) k j 0 ~ 64
11. Sharpness k k 0 ~ 64
12. OSD Select k l 0 ~ 1
13.
Remote control lock mode
k m 0 ~ 1
14. PIP/DW k n 0 ~ 3
15. PIP Position k q 0 ~ 3
16. Balance k t 0 ~ 64
17.
Colour Temperature
k u 0 ~ 3
18. Red Adjustment k v 0 ~ 50
19. Green Adjustment k w 0 ~ 50
20. Blue Adjustment k $ 0 ~ 50
21. PIP input Source k y Refer to p. 81
22. Abnormal Status k z 0 ~ a
23. ISM Method (option) j p Refer to p. 81
24. Low Power (option) j q 0 ~ 1
25. Orbiter Time Setting (option) j r 1 ~ FE
26. Orbiter Pixel Setting (option)j s 1 ~ 3
27.
Picture Size Setting for DW Mode
jt
0
~
20
28. Auto Configure j u 1
29.
Channel Select Command
m a Refer to p. 82
30. Send IR Code m c Key Code
31. Input select (Main) x b Refer to p. 83
32. Input select (PIP) x y Refer to p. 83
Communication Parameters
■
Baud rate : 9600 bps
(
UART
)
■
Data length : 8 bits
■
Parity : None
■
Stop bit : 1 bit
■
Communication code : ASCII code
■
Use a crossed (reverse) cable.
Transmission
*
[Command 1] : First command to control the set.
(j, k, m or x)
*
[Command 2] : Second command to control the set.
*
[Set ID] : You can adjust the Set ID to choose
desired monitor ID number in special
menu.
Adjustment range is 1 ~ 99.
When selecting Set ID ‘0’, every
connected the set is controlled.
Set ID is indicated as decimal (1~99) on
menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
*
[DATA] : To transmit command data.
Transmit ‘FF’ data to read status of
command.
*
[Cr] : Carriage Return
ASCII code ‘0x0D’
*
[ ] : ASCII code ‘space (0x20)’
[Command1][Command2][ ][Set ID][ ][Data][Cr]
OK Acknowledgement
* The set transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if
the data is data read mode, it indicates present status
data. If the data is data write mode, it returns the
data of the PC computer.
[Command2][ ][Set ID][ ][OK][Data][x]
Error Acknowledgement
* The set transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
[Command2][ ][Set ID][ ][NG][Data][x]
Transmission / Receiving ProtocolCommand Reference List
*
When setting the 22 ~ 32, a menu doesn’t display on screen.
Data 1: Illegal Code
2: not support function
3: Wait more time
COMMAND
1
COMMAND
2
DATA
(Hexadecimal)