22LY560M 28LY560M 32LY560M 42LY560M Hospital TVs Commercial Mode Setup Guide Note: Selected features shown within this guide may not be available on all models. EXPERIENCED INSTALLER Express Script Installer Menu Wizard pages 12 – 17 Custom Master TV Setup pages 31 – 35 FTG Mode of Operation pages 46 – 52 © Copyright 2014 LG Electronics U.S.A., Inc.
For Customer Support/Service, please call: 1-888-865-3026 The latest product information and documentation is available online at: www.LGsolutions.com MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________ Serial No._______________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . .3 – 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . . . . . . 6 – 9 Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pass-through Mode . . . . . . . . . . . . . . . . .
Commercial Mode Overview This document describes how to set up LY560M Pro:Centric ® TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU or Protocol Translator Card (PTC) or it resides externally from the TV (i.e., in a device from the solution provider). These TV models are capable of Free-To-Guest (FTG) Mode operation via the TV CPU.
Commercial Mode Overview (Cont.) Installer Menu To create a customized Master TV Setup, you will need to know how to access the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to pages 21 to 30 for information on accessing the Installer Menu and for detailed descriptions of the Installer Menu items.
Commercial Mode Overview (Cont.) FTG Mode Features FTG Mode provides the following features: • Logical or physical tuning of physical RF channels and Aux inputs. • Mapping of RF channels with minor (program) numbers up to 999. • FTG Channel Map of up to 600 channels. • Start Channel set for RF or Aux input delivered content. • Pro:Centric data delivery over RF or IP. • TV Zoning option for location-specific configuration. LG’s FTG File Manager PC software enables you to create an FTG Configuration (.
Commercial Mode Overview (Cont.) Determining the TV Operating Mode To determine the operating mode of the TV, press MENU on the Installer Remote. The menu displayed depends on the operating mode. See examples below. If the Function Menu appears, the TV is in a mode (FTG, PPV, etc.) that does not allow the end user to change the fundamental TV setup. If the TV setup menus appear, the TV is in Pass-through Mode. ASPECT RATIO ABC Move Function Menu Indicates the TV is not in Passthrough Mode.
Pro:Centric Operation Pro:Centric Interactive Menu Features LG’s Pro:Centric application enables patients and visitors to locate and select television entertainment using an interactive channel guide, check the daily weather, and view hospital and surrounding amenities via custom billboards and points-of-interest maps. Pro:Centric application features include: • Portal and information screens/pages (including a “Welcome” page) that include branding logos.
Pro:Centric Operation (Cont.) Pro:Centric Setup Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric Server Admin Client User Guide. This document describes only those settings that must be specified on the TVs to enable the Pro:Centric remote management facilities and/or the Pro:Centric application.
Express Script Installer Menu Wizard The Express Script Installer Menu Wizard guides you through the process of setting up the essential items for most hospital TV viewing applications and also enables you to configure the Pro:Centric settings on the TV. The wizard will appear on the screen each time the TV is turned ON, until configuration is completed or the wizard is exited. Use the Installer Remote to make selections and complete each wizard step.
Express Script Installer Menu Wizard (Cont.) Configure Pro:Centric Settings The next wizard screen enables you to set up the Pro:Centric feature of the TV. By default, the Data Channel is configured for Auto Search, which enables the TV’s Data Channel Auto Search feature to set the Data Channel value. See item 119 DATA CHANNEL description on page 30 for further information on the Data Channel Auto Search feature.
Express Script Installer Menu Wizard (Cont.) (Continued from previous page) 2. In the Pro:Centric Mode field, use the Left/Right arrow keys on the Installer Remote to select the appropriate Pro:Centric Application Mode—GEM, FLASH, or Configuration Only. 3. Once the fields are completed as required, you have two options: • To proceed with TV configuration via the wizard, select Next and press OK on the Installer Remote. See also “Complete the TV Configuration” below.
Express Script Installer Menu Wizard (Cont.) (Continued from previous page) 3. Select the speaker configuration. Use the Up/Down arrow keys on the Installer Remote to select the speaker configuration field, and then use the Left/Right arrow keys to select the appropriate speaker: Pillow Only (default), TV Only, or Pillow & TV. When you have made your selection, use the arrow keys to select Next, and then press OK. 4. Select the pillow speaker code.
Express Script Installer Menu Wizard (Cont.) (Continued from previous page) Note: You MUST select Execute Auto Search and press OK in order to run the channel scan. If you move on to the next step without running the Auto Search, there will be no analog or digital channels in the channel lineup (Channel Map). In this case, upon completion of the Express Script, the only channels in the resulting PTC Channel Map will be any enabled Aux inputs.
Express Script Installer Menu Wizard (Cont.) (Continued from previous page) When you are finished, press MENU to close the pop-up window. Use the arrow keys to select Next, and then press OK. Installer Menu Wizard 1 ► 2 ► 3 ► 4 ► 5 ► 6 ► 7 ► 8. Completion. In the final step, the TV saves your settings and transfers the setup to the commercial controller (PTC). (This is similar to 2-5-5 + MENU Mode during Custom Master TV Setup.
Ez Download Utility The Ez Download utilty, available from the TV Manager / USB Download Menu, enables you to select multiple files at one time from the files loaded on a USB memory device. You may use this utility to download any one or all of the following to a TV: a TLX file for configuration purposes, a TLL file for cloning purposes (legacy), a TV CPU or PTC software update, a splash screen image. Before You Begin • Ensure the USB device has been formatted with FAT format.
Ez Download Utility (Cont.) (Continued from previous page) 4. To access the TV Manager / USB Download Menu from the TV menus: • Press MENU on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode). • Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times. 5.
Ez Download Utility (Cont.) (Continued from previous page) Note: There are no options available/applicable for TLL files. Note: Press on the Installer Remote, as necessary, to exit the Ez Download screen and/or the TV Manager / USB Download Menu and return to TV viewing. 8. When you are ready to continue, use the arrow keys on the Installer Remote to select Apply, and then press OK. The TV will show download progress in a new window. Do NOT remove the USB device until downloading is complete.
Installer Menu Use the Installer Menu to set up, change, or view operational settings. This section describes how to access, use, and exit the Installer Menu from the TV itself. However, you should also refer to the Installer Menu descriptions in this document if you are configuring the TV using an FTG Configuration (.tlx) file created using LG’s FTG File Manager software. Refer to the table on pages 23 and 24 for brief descriptions of Installer Menu items.
Installer Menu (Cont.) As part of the Installer Menu header (in all modes), two 3-character acronyms are displayed to indicate the TV’s current configuration mode. The table below lists all possible mode identifiers for these TV models.
Installer Menu (Cont.) Installer Menu Items 000 through 047 Item Function Value Range Default Value 000 001 Brief Description of Function INSTALLER SEQ 0~3 0 Leave default set to 0. POWER MANAGE 0~7 0 Sets number of hours of no activity before automatic shutoff. 002 AC ON 0/1 0 Set to 1 to enable TV to turn ON when AC power is applied. 003 BAND/AFC 0~3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC 004 STRT CHANNEL 0 ~ 127, 255 255 Channel tuned when TV is turned ON.
Installer Menu (Cont.) Installer Menu Items 053 through 122 Item Function Value Range Default Value 053 069 Brief Description of Function DIS. CH-TIME 0/1 0 Set to 1 to disable Channel-Time display. EN. CH-T COL. 0/1 1 Set to 1 to enable custom color for the Channel-Time display. 070 FOR. CH-TIME 0~7 2 Chooses custom foreground color for the Channel-Time display. 071 BCK. CH-TIME 0~7 2 Chooses custom background color for the Channel-Time display.
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Management is Off.
Installer Menu (Cont.) 012 - IR BANKS EN (IR Banks Enable) For direct access to a particular channel bank. When enabled, you can access a channel bank by inputting the discrete IR code for that bank. Note: This item is not available in the Installer Menu when item 027 HOSPITAL MODE is set to 0. 013 - SCAN MODE (Functional after 2-5-5 + MENU transfer of Channel Map) When set to 1 (default), allows TV to be turned ON when Channel Up/Down buttons are pressed on pillow speaker.
Installer Menu (Cont.) When Hospital Mode is enabled and the TV is in Pass-through Mode, channel banks are also available. Refer to channel banks information in this document for further details. Channel banks are not supported if Hospital Mode is set to 0 or on TVs that are configured for FTG Mode operation. When Hospital Mode is set to 0 (disabled), both the IR code that will control the TV and the speaker selection depend on the Installer Menu item 020 FEATURE LEVEL setting.
Installer Menu (Cont.) 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display. 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable number, most significant byte-2 readable by MPI command. Note: Not linked to serial number. 070 - FOR.
Installer Menu (Cont.) 096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up: 0 = Set By System 1 = 4:3 2 = 16:9 (default) 3 = Just Scan 4 = Zoom Note: This item is not available in the Installer Menu unless item 106 ASP RATIO LOCK is set to 0.
Installer Menu (Cont.) 117 - FACT DEFAULT (Factory Default) Set to 1 and press OK to restore the factory default settings of all Installer Menu items. Once complete, the value returns to 0. Caution: If set to 1, this clears all Installer Menu custom settings and restores the factory default settings. It also clears the channel lineup, including any assigned channel icons and custom text labels. Note: See also Reference section, “Restoring Factory Defaults on the TV(s),” for further information.
Custom Master TV Setup This section describes how to create a customized Master TV Setup for cloning purposes when the TV is in Pass-through Mode. Note: Cloning requirements and procedures are described in detail on pages 41 to 45. Refer to FTG Mode information on pages 46 to 52 for details on entering FTG Mode and configuring/editing the FTG Channel Map and FTG Installer Menu settings.
Custom Master TV Setup (Cont.) Custom Master TV Setup Procedure 1. Turn ON the TV. If the Express Script Installer Menu Wizard appears on the screen when you turn ON the TV, exit the wizard. 2. Set Installer Menu items. This step provides specific instruction only on the Installer Menu items that should be set on a Master TV. Refer to pages 21 to 30 for detailed information on all Installer Menu items.
Custom Master TV Setup (Cont.) (Continued from previous page) 3. Set up TV features. On-screen setup menus control the features of the TV. Press MENU on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Audio, etc. options to the desired configurations. See “Clonable TV Setup Menu Features” list page 31 and also notes below.
Custom Master TV Setup (Cont.) (Continued from previous page) 5. (PTC cloning only) Transfer the auto-tuned/edited channel lineup (if applicable) and TV setup menu settings to the PTC: 2-5-5 + MENU Mode Note: This step is essential for successful cloning using a TLL file. Without this step, the PTC will not contain any channels or TV setup menu settings. Note: The maximum number of channels (analog, digital, and Aux inputs) that can be transferred to the PTC is 141.
Custom Master TV Setup (Cont.) (Continued from previous page) 7. Verify the TV setup. Make sure the TV features are set per your requirements. Also, if cloning an auto-tuned/edited channel lineup, verify that the channel lineup, channel icons, and custom text labels (as applicable) are correct. 8. Set up channel banks. Set up channel banks, as desired (see pages 37 to 40).
Channel Icons / Custom Text Labels (2-5-4 + MENU Mode) Changing Channel Icons and/or Adding or Editing Custom Text Labels in the Channel-Time Display If there is no pre-assigned icon for a channel, you can add a custom text label of up to seven (7) characters to help identify the channel or network. Also, if desired, a custom text label can be added to the Channel-Time display in addition to a pre-assigned icon.
Channel Banks Setup Channel Banks Overview Channel Banks enable institution administrators to create tiered channel programming on patient in-room TVs. Each channel bank may offer a custom channel lineup for a pre-determined fee. LY560M TVs are configured with four channel banks, i.e., Channel Banks 1, 2, 3, and 4. The top tier generally contains the most programming (premium, etc.), 2nd tier = lesser programming, 3rd tier = basic programming, etc.
Channel Banks Setup (Cont.) Channel Status Options for Channel Banks In the Channel Preview/Banks Setup Menu, use the Channel Up/Down arrows on the Installer Remote to navigate to a channel and the Left/Right arrows to select the channel status. CHANNEL PREVIEW - BANK 1 CH 011-001 NORMAL-ADDED IDs currently selected channel bank. IDs currently selected channel. IDs channel status in selected bank. Enter -> Change CC -> VCHIP Menu, Ch.
Channel Banks Setup (Cont.) Inactive TV Setup There are two options for creating an inactive TV display on Channel Bank 4. Either: • Select NORMAL-DELETED for each channel in Channel Bank 4, or • Press CH. BANK on the Installer Remote until Channel Bank 4 is selected, and then press CH. PREVIEW to display the Channel Preview/Banks Setup Menu. Then, press the SAP key on the Installer Remote to automatically delete all channels in Channel Bank 4.
Channel Banks Worksheet Use this worksheet to plan your program packages. (Photocopy additional worksheets as needed.
Cloning Procedures Cloning Overview Cloning refers to the process of capturing a Master TV Setup and transferring it to a Target TV that is to remain in Pass-through Mode. There are two different procedures for cloning a Master TV Setup, each with its own advantages and limitations (see also “Cloning Methods” on page 31): • Using a USB memory device / TLX file • Using a USB memory device / TLL file Each cloning method is described in further detail on the pages that follow.
Cloning Procedures (Cont.) Learn Setup from Master TV 1. Ensure the Master TV is set up completely and in Pass-through Mode. 2. Insert the USB memory device into the USB port on the Master TV. TV Manager 3. Press MENU on the Installer Remote to display the TV setup menus. Use the arrow navigation keys to select/highlight the Option menu icon, and then press the number “7” key a total of seven times to display the TV Manager / USB Download Menu.
Cloning Procedures (Cont.) (Continued from previous page) 3. If the Master TV Setup contains a TV Zone # assignment, make sure to assign the same Zone designation in the Target TV at this time. See Reference section, “Using the TV Zoning Feature,” for further information. TV Manager USB Ez Download Logo Image Download Note: In order for the proper location-specific TV Zone profile data to be applied, the Zone designation must be assigned in the Target TV(s) BEFORE Teaching is performed.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using a TLL File This section describes how to Learn and/or Teach a Master TV Setup using a TLL file. Before You Begin • Learning and Teaching is only possible between identical model TVs. • Complete the Custom Master TV Setup procedure or run the Express Script Installer Menu Wizard (see pages 31 to 35 or pages 12 to 17, respectively). • Both the Master and Target TVs must be in Pass-through Mode (i.e.
Cloning Procedures (Cont.) Teach Master TV Setup to Target TV Note: You may also use the Ez Download utility to complete the Teaching process, if desired. See “Ez Download Utility” on pages 18 to 20 for further information. 1. Turn ON the Target TV. The next step depends on whether the Express Script Installer Menu Wizard appears on the screen: • If the wizard is displayed, the TV is in the required factory default state. Exit the wizard, and then, go to step 3.
FTG Mode of Operation This section describes how to create an FTG Configuration (.tlx) file using the FTG File Manager. It also describes how to locally configure a TV for FTG Mode operation. See also the FTG Mode overview on pages 7 to 8 for further information on FTG Mode. Creating an FTG Configuration File The procedure below describes how to use the FTG File Manager utilities to create an FTG Configuration (.tlx) file that can be saved to a USB memory device.
FTG Mode of Operation (Cont.) (Continued from previous page) Note: To clear the current TLX File Contents, click the New button in the TLX File command section of the FTG File Manager main screen (above the TLX File Contents window). 3. To add an FTG Channel Map to the FTG Configuration List, click will copy the current mapped channels to the FTG Configuration List. under FTG Channel Map.
FTG Mode of Operation (Cont.) Teaching FTG Configuration to a TV This section describes how to transfer (Teach) an FTG Configuration file from a USB memory device to a TV, using the TV Manager / USB Download Menu “Teach To TV (TLX)” option. The FTG Configuration file may be created either in the FTG File Manager or from a Master TV Setup that was saved (Learned) from a Master TV.
FTG Mode of Operation (Cont.) (Continued from previous page) Note: In order for the proper location-specific TV Zone profile data to be applied, the Zone designation must be assigned in the Target TV(s) BEFORE Teaching is performed. 3. Insert the USB memory device that contains the FTG Configuration file into the USB port. 4. Press MENU on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode). TV Manager USB 5.
FTG Mode of Operation (Cont.) Learning FTG Configuration from a TV To ensure that decryption of Pro:Idiom encrypted channels is enabled, it is recommended that you create an FTG Configuration file using the FTG File Manager as described on pages 46 to 47. However, if necessary, there is an option to save (Learn) an FTG Configuration file from an LY560M TV to a USB memory device.
FTG Mode of Operation (Cont.) (Continued from previous page) 6. In the Learn From TV (TLX) window, to differentiate this TLX file from others, you can use the Up/Down arrow keys to change the last five digits of the filename. Press OK when you are ready to initiate Learning. Learning status will be shown on a progress bar in a new window. Do NOT remove the USB device until Learning is complete. When the Learning process is complete, the TV Manager / USB Download Menu will reappear on the screen. 7.
FTG Mode of Operation (Cont.) (Continued from previous page) 3. Set Installer Menu item 117 FACT DEFAULT to 1 and press OK on the Installer Remote. This clears all Installer Menu custom settings, the channel lineup, etc. and restores the factory default settings. The value will change back to 0 after the commercial controller (PTC) has been restored to factory default condition. This step ensures that the TV Channel Memory will be the active channel lineup. 4.
FTG File Manager Utilities Overview FTG File Manager Main Screen The FTG File Manager main screen enables you to compile, modify, and save FTG Configuration (.tlx) files. It also allows you to change the Zone assignment for each Installer Menu profile, if desired (see Reference section, “Using the TV Zoning Feature,” for further information). FTG CONFIGURATION LIST Data to be saved in FTG Configuration (.tlx) file. CLEAR/SAVE FTG Configuration and TV Setup Menu List options. NEW/OPEN TLX File options.
FTG File Manager Utilities Overview (Cont.) FTG Channel Map Configuration Utility The FTG Channel Map Configuration Utility enables you to create, view, edit, and print a Logical Channel Map. EDIT/ADD MAP Click to open the FTG Channel Map Editor to create or edit an FTG Channel Map (see next page). PRINT MAP Click to display a printable FTG Channel Map Report. The report can also be exported as an HTML or Text file. Filename of opened FTG Configuration (.
FTG File Manager Utilities Overview (Cont.) FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map. LOGICAL CHANNEL MAPPING Select a Logical Channel number. Then, assign it the RF, Major, and Minor channel numbers to complete the mapping. CUSTOM CHANNEL LABELS/ICONS Enter custom labels and select icons by name on menu or by number. SET CHANNEL ATTRIBUTES Check/select Encrypted, OSD, or Blank Video.
FTG File Manager Utilities Overview (Cont.) FTG Installer Menu Configuration Utility CONFIGURATION SETTINGS Select tabs for categories of Installer Menu items to set up TV. Filename of opened FTG Configuration (.rml) file created using FTG Device Configuration Application. Notes: • The Pro:Centric tab enables you to set up Pro:Centric-specific parameters. Refer to the Free-ToGuest (FTG) File Manager User Guide for further information. • LAN parameters are not applicable for these TV models.
IP Environment Move OK IP Environment Setup The IP Environment Menu enables you to set up the network features of the TV. With the exception of Network Connection settings, the IP Environment settings are editable (with the Installer Remote) only if the TV is in Pass-through Mode and read-only when the TV is not in Pass-through Mode.
IP Environment Setup (Cont.) (Continued from previous page) The next Network Setting window will enable you to specify the IP and DNS configuration for this TV. Auto settings will be selected by default. Use the arrow keys to select the appropriate options, and specify the configuration data for the IP and DNS modes. When all fields are completed, select OK on the screen and press OK on the Installer Remote. Network Setting Select the IP setting mode.
IP Environment Setup (Cont.) IP Environment Move OK IP Environment Move OK Pro:Centric Setup Pro:Centric options enable you to configure the TV with the appropriate settings to connect to the Pro:Centric server. Use the Up/Down arrow keys on the Installer Remote to navigate between fields. 1. With the IP Environment Menu on display, use the arrow keys on the Installer Remote to select Pro:Centric. Then, press OK.
IP Environment Setup (Cont.) (Continued from previous page) IP Configuration a) In the Media Type field, use the Left/Right arrow keys to select IP. Note: If the Media Type has already been set in the Express Script Installer Menu Wizard, the specified value will be reflected in this field. Note: Setting the Media Type to “IP” automatically sets the Data Channel field to “253.” You cannot alter this setting (unless you revert Media Type to “RF”).
Reference: Upgrading TV/PTC Software using a USB Memory Device This section describes how to update TV (CPU) and/or PTC software using the TV Manager / USB Download Menu “Upgrade TV Software” and/or “Update PTC Software” option(s), respectively, though you may also use the Ez Download utility to upgrade software, if desired. See “Ez Download Utility” on pages 18 to 20 for further information.
Reference: Downloading a Splash Screen using a USB Memory Device This section describes how to download a splash screen image using the TV Manager / USB Download Menu “Logo Image Download” option, though you may also use the Ez Download utility to download the splash image, if desired. See “Ez Download Utility” on pages 18 to 20 for further information. Splash Screen Image File Guidelines • The splash screen image must be a baseline (not progressive) JPEG. • The image should be no larger than 1 MB.
Reference: Power Consumption Settings The following tables assume that Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 255). 22LY560M Item 099 Back Lighting (Static) 28LY560M 32LY560M 42LY560M Power Consumption (Watts) Percent Savings Power Consumption (Watts) Percent Savings Power Consumption (Watts) Percent Savings Power Consumption (Watts) Percent Savings 100 20.7 0% 22.5 0% 43.6 0% 72.0 0% 90 80 70 60 50 40 30 20 10 1 20.4 20.3 20.2 20.0 19.8 19.5 18.
Reference: TV Aux Input Configuration ENABLE DIRECT ACCESS Tuning * TV MPI DATA MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) Installer Menu DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) DATA STATUS TYPE 0x0D AUX SOURCE (R) Installer Menu Item 029 OLD OCV =0 Installer Menu Item 029 OLD OCV =1 Aux Input Input Mode Item Function Value Enable Bit Label Value Value Description 131 91 Video1 (Rear) CV 39 REAR AUX EN 1 1 Rear Video (Aux) 1 0 VIDEO 132 92 HDMI2 91 HDMI2 ENABLE 2
Reference: Auto Input(s) Sensing Feature This section provides detailed settings information for Installer Menu item 042 AUTO INPUTS. To disable auto-sensing for all available Aux inputs, set item 042 to 0. To enable auto-sensing for all available Aux inputs, set item 042 to 255. For specifications on all other available settings (i.e., settings for individual inputs), refer to the table on the following page.
Reference: Auto Input(s) Sensing Feature (Cont.
Reference: LY560M Hospital Operations Hospital Features The following table identifies when and how the LY560M hospital features are supported in three different TV configurations. As indicated in the introduction to this document, LG commercial TV functionality is based on “ownership” of the Channel Map. For the purposes of this table, “CPU” indicates that the TV is in Pass-through Mode with the Channel Map in the CPU (i.e.
Reference: LY560M Hospital Operations (Cont.) Speaker Selection The following table outlines speaker settings as determined by Installer Menu items 027 HOSPITAL MODE and 020 FEATURE LEVEL.
Reference: Restoring Factory Defaults on the TV(s) This section describes how to restore all factory defaults or just the Installer Menu factory defaults either on a single TV that is currently in Pass-through or FTG Mode or on multiple TVs that are currently in FTG Mode. Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV to Passthrough Mode.
Reference: Using the TV Zoning Feature This section describes the TV Zoning feature available with the LY560M model TVs. The TV Zoning feature enables you to create localized configurations for TVs in selected locations, or “Zones,” within the installation environment, for example, a hotel lobby, fitness center, restaurant, etc. This feature is primarily intended for use when the TV is configured for FTG Mode operation.
Reference: Using the TV Zoning Feature (Cont.) Note: While a channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one Zone. See also the FTG Channel Map Editor overview on page 55. At the same time, keep in mind that the TV Zone designations are not mutually exclusive.
Reference: 22/28LY560M Rear and Side Jack Panels HDMI IN 1 Connection for HDMI output from external device. UPDATE Restricted to software updates. SPEAKER OUT / LINE OUT (3.5 mm jack) Connect external audio (fixed speaker, variable speaker, or fixed line level [amplifier]) equipment. See Reference section, “External Stereo Speaker Setup,” for further information. RESET Initiates a hardware reset and turns the TV OFF. PILLOW SPEAKER SERVICE ONLY Connect pillow speaker here.
Reference: 32/42LY560M Rear and Side Jack Panels HDMI IN 1 Connection for HDMI output from external device. RGB IN (PC) Connection for RGB output from PC. UPDATE Restricted to software updates. MPI When the TV is in Pass-through Mode, the MPI function enables an external MPI control device (i.e., VOD/PPV STB, etc.) to control the TV. RESET Initiates a hardware reset and turns the TV OFF. SERVICE ONLY PILLOW SPEAKER Restricted to service updates. Connect pillow speaker here.
Reference: External Stereo Speaker Setup The three-contact (left, right, ground) SPEAKER OUT 3.5 mm jack on the LY560M rear panel provides stereo speaker signal outputs (fixed speaker, variable speaker, or fixed line level [amplifier]) for external audio equipment. Set Installer Menu item 097 AUDIO OUTPUT as required in accordance with external audio equipment connected to the TV. Also, refer to the following diagram for pinout details. Caution: Do NOT plug in a mono connector, as this may damage the TV.
Reference: Installer Remote Control Typical Key Functions An LG Installer Remote is required to set up and operate the TV. The LG Installer Remote illustrated below shows typical remote control functions and is provided for reference only. TV LG1/TV LG2 & TV Z1/TV Z2 Selects the IR codes sent by the remote to match the setting in the TV. NUMBER Buttons (0 - 9) & DASH Use to enter a channel or program number. Dash is used for sub-channel numbers such as 9-1, 9-2, etc.
Reference: Pillow Speaker Setup The pillow speaker will only be functional after the Express Script/Custom Master TV Setup and/or cloning procedures are complete. Note: When Installer Menu item 027 HOSPITAL MODE is set to 254 (factory default value), there is no power (voltage) supplied to the pillow speaker. Connecting a Pillow Speaker to the TV Connect the pillow speaker (see example at right) to the PILLOW SPEAKER interface on the rear jack panel of the TV.
Reference: USB Media Navigation using Pro:Centric Pillow Speaker The Pro:Centric pillow speaker is currently the only pillow speaker that enables users to navigate and play/view USB media files (videos, music, photos, etc.). This section provides a brief overview of the Pro:Centric pillow speaker navigation tools. Note: Refer to the Owner’s Manual for detailed information on USB memory device requirements and the types of media supported by the LY560M TVs. 1.
Reference: VESA Standard TV Mounts General Guidelines: Choosing a Location for Installing a VESA Standard Mount To the right are some examples of VESA standard mounts. Since there are numerous types of stands and mounts available, only a few are shown here. Refer to the instructions provided with the TV stand that will be used to mount the TV. Be sure the style of stand selected is capable of supporting the weight of the TV and is appropriate for the application.
Troubleshooting General Troubleshooting (Some Quick and Easy Tips for Resolving Problems) Installation Symptom Possible Cause(s) Possible Solution(s) Cannot direct enter channel number. (TV in Pass-through Mode) Installer Menu item 028 CH. OVERIDE is set to 0, i.e., disabled and/or Channel Access was denied in Express Script. (TV in FTG Mode) The channel entered is not included in the FTG Channel Map. Auto Tuning (Channel Search) not run.
Troubleshooting (Cont.) Commercial Mode Check Use this flowchart to determine whether the TV is currently in Commercial Mode. Press POWER on Installer Remote. TV turned ON? No TV connected to AC Power? No Plug into AC Power outlet. Yes Yes Bad TV Leave the TV set ON, and press MENU on the Installer Remote. Function Menu on display? Yes TV is in Commercial Mode. 80 No Press MENU repeatedly as if to access the Installer Menu.
Troubleshooting (Cont.) Channel Banks Setup Troubleshooting CHANNEL PREVIEW - BANK 1 CH 011-001 NORMAL-ADDED Enter -> Change CC -> VCHIP Menu, Ch. Preview -> Exit Channel Preview/Banks Setup Menu Symptom Possible Cause Possible Solution Cannot change channel status in menu. Channel Access was denied in Express Script and/or Installer Menu item 028 CH. OVERIDE is set to 0. Set CH. OVERIDE to 1 to allow access for channel status change. Channel Preview/Banks Setup Menu does not appear.
Glossary of Terms Channel Lineup Channels set in the TV memory, via Auto Tuning/manual editing. Channel Banks Enables tiered channel programming options for hospital models. Each channel bank may offer a custom channel lineup. Cloning The process of capturing a Master TV Setup and transferring it to a Target TV using a USB memory device.
Document Revision History / Open Source Software Notice Document Revision History Date Description June 2014 Revision A: New document Product documentation is available online at: www.LGsolutions.com. Open Source Software Notice To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com.
For Customer Support/Service, please call: 1-888-865-3026 www.LGsolutions.com Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a registered trademark of LG Electronics Inc. All other trademarks or registered trademarks are the property of their respective owners. © Copyright 2014 LG Electronics U.S.A., Inc.