ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under Appendix A “Notices” on page 205. Fourth Edition (May 2011) © Copyright Lenovo 2009, 2011. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents About this manual. . . . . . . . . . . iii Chapter 1. Safety information . . . . . 1 General safety . . . . . . . . . . . . . . . Electrical safety . . . . . . . . . . . . . . Safety inspection guide . . . . . . . . . . . Handling devices that are sensitive to electrostatic discharge. . . . . . . . . . . . . . . . . Grounding requirements . . . . . . . . . . . Safety notices (multilingual translations) . . . . . Laser compliance statement (multilingual translations) . . . . . . . . . . . . . . .
1070 DIMM (upper slot) . . . . . . . . . . 1080 PCI Express Mini Card for wireless LAN . 1090 PCI Express Mini Card for wireless WAN . 1100 Keyboard bezel assembly . . . . . . . 1110 Bluetooth daughter card (BDC-2.1) . . . 1120 Backup battery . . . . . . . . . . . 1130 Smart Card or Contactless Smart Card or Smart Card dummy spacer . . . . . . . . . 1140 Speaker assembly . . . . . . . . . . 1150 Thermal module . . . . . . . . . . . 1160 CPU . . . . . . . . . . . . . . . 1170 LCD unit . . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad T510 and T510i MT 4313, 4314, 4339, 4349, 4384, 4484, and 4873 ThinkPad W510 MT 4318, 4319, 4387, 4389, 4391, 4875, and 4876 Use this manual along with the advanced diagnostic tests to troubleshoot problems. Important: This manual is intended only for trained service technicians who are familiar with ThinkPad products.
iv ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 1. Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad Notebook.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
– Send another person to get medical aid. Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
When handling ESD-sensitive parts: • Keep the parts in protective packages until they are inserted into the product. • Avoid contact with other people. • Wear a grounded wrist strap against your skin to eliminate static on your body. • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. • Use a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.
DANGER DANGER DANGER DANGER DANGER Chapter 1.
DANGER 6 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
PERIGO PERIGO PERIGO Chapter 1.
PERIGO PERIGO PERIGO PERIGO PERIGO DANGER 8 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
DANGER DANGER DANGER DANGER DANGER Chapter 1.
DANGER DANGER VORSICHT VORSICHT VORSICHT 10 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
VORSICHT VORSICHT VORSICHT VORSICHT VORSICHT Chapter 1.
12 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 1.
14 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 1.
16 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese Chapter 1.
18 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 1.
20 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 1.
22 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 1.
24 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 2.
• If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change. Replace only the FRU that changed the symptoms. Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings.
• The PEW record is the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). • eSupport will show both the CTO and CMV machine type models (Example: 1829-CTO and 1829-W15 will be found on the eSupport site.) • The HMM will have the 4-digit MT and 3-digit CTO model only (Example: 1829-CTO). Again, CMVs are custom models and are not found in the HMM. General Announce Variant (GAV) This is a standard model (fixed configuration). GAVs are announced and offered to all customers.
28 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 3. General checkout This chapter presents following information: • “What to do first” on page 29 • “Checkout guide” on page 30 – “Diagnostics using PC-Doctor for DOS” on page 30 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 33 – “PC-Doctor for Rescue and Recovery” on page 34 – “FRU tests” on page 34 • “Power system checkout” on page 35 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program.
Following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use.
Note: If a supervisor password has been set by the customer, BIOS Setup Utility menu appears after the password is entered. You can start the BIOS Setup Utility by pressing Enter instead of entering the supervisor password; however, you cannot change the parameters that are protected by the supervisor password. On the BIOS Setup Utility screen, press F9, Enter, F10, and then Enter. Note: When you initialize the computer configuration, some devices are disabled, such as the serial port.
Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Fixed Disks Diskette Drives Other Devices Communication Wireless LAN Advanced Memory Tests PC-DOCTOR 2.0 Copyright 2008 PC-Doctor, Inc. All Rights Reserved. Use the cursor keys and ESC to move in menus. Press ENTER to select.
Hardware Info • • • • • • • • • • • System Configuration Memory Contents Physical Disk Drives Logical Disk Drives VGA Information IDE Drive Info PCI Information PNPISA Info SMBIOS Info VESA LCD Info Hardware Events Log Utility • • • • • • • • • • • Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick Erase Hard Drive Lenovo ThinkVantage Toolbox (Lenovo System Toolbox) Lenovo ThinkVantage® Too
PC-Doctor for Rescue and Recovery In some models of ThinkPad Notebook, the Rescue and Recovery® workspace enables you to run the PC-Doctor program to test the hardware features of the computer. To run the test, click “Run Diagnostics” on the Rescue and Recovery main screen. FRU tests The following table shows the test for each FRU. Table 1. FRU tests FRU System board Applicable test 1. Diagnostics ➙ CPU/Coprocessor 2. Diagnostics ➙ Systemboard 3.
Table 1. FRU tests (continued) FRU Applicable test TrackPoint or pointing device If the TrackPoint does not work, check the configuration as specified in the BIOS Setup Utility. If the TrackPoint is disabled, select Automaticto enable it. After you use the TrackPoint, the pointer may drift on the screen for a short time. This drift can occur when a slight, steady pressure is applied to the TrackPoint pointer. This symptom is not a hardware problem.
3 2 1 Pin Voltage (V dc) 1 +20 2 0 3 Ground (20V) Note: Output voltage of pin no.2 of the ac adapter may different from the one you are servicing. 3. If the voltage is not correct, replace the ac adapter. 4. If the voltage is acceptable, do the following: • Replace the system board. • If the problem persists, go to “FRU tests” on page 34. Note: Noise from the ac adapter does not always indicate a defect.
1(+) 2(+) 5 3 4 6(-) Terminal Voltage (V dc) 1 + 0 to + 12.6 7 Ground (-) 7(-) 3. If the voltage is less than +11.0 V dc, the battery pack has been discharged. Note: Recharging will take at least 3 hours, even if the indicator does not turn on. If the voltage is still less than +11.0 V dc after recharging, replace the battery. 4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 5 and 7. The resistance must be 4 to 30 K Ω.
38 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 4. Related service information This chapter presents following information: • “Restoring the factory contents by using Recovery Disc Set” on page 39 • “Passwords” on page 40 • “Power management” on page 42 • “Symptom-to-FRU index” on page 43 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
3. Press F10 to save the Setup Utility configuration changes. Follow the instructions on the screen to begin the recovery process. 4. Select your language and click Next. 5. Read the license. If you agree with the terms and conditions, select I accept these terms and conditions and then click Next. If you do not agree with the terms and conditions, follow the instructions on the screen. 6. Click Yes in the displayed window to begin the operating system recovery process. 7.
service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee. For how to remove the POP, see “How to remove the hard-disk password” on page 41. Supervisor password A supervisor password (SVP) protects the system information stored in the BIOS Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration.
2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility. For models supporting the Passphrase function, press F1 while HDP icon is appearing on the screen; then enter the master HDP. For the other models, enter the master HDP. Note: To check whether the ThinkPad Notebook you are servicing supports the Passphrase function, enter the BIOS Setup Utility and go to Security ➙ Password.
Note: Even if you do not set the low-battery alarm, the charge indicator notifies you when the battery is low, and then the computer enters the power-saving mode automatically. To cause the computer to return from sleep (standby) mode and resume operation, do one of the following: • Press the Fn key. • Open the LCD cover. • Turn on the power switch.
• • “Intermittent problems” on page 50 “Undetermined problems” on page 51 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type. Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or action, in sequence.” If replacing a FRU does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
Table 2. Numeric error codes (continued) Symptom or error 0191 System Security—Invalid Remote Change requested. FRU or action, in sequence 1. Run BIOS Setup Utility, and then save current setting by pressing F10. 2. System board. 0192 System Security— Embedded Security hardware tamper detected. System board. 0193 RF antenna has been removed Enter the supervisor password. 0194 The computer has been carried through a security gate Enter the supervisor password.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0231 System RAM error—System RAM fails at offset nnnn. 1. DIMM. 2. System board. 0232 Extended RAM error— Extended RAM fails at offset nnnn. 1. DIMM. 2. System board. 0250 System battery error—System battery is dead. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1802 Unauthorized network card is plugged in—Turn off and remove the miniPCI network card. 1. Remove Mini PCI network card. 2. System board. 1803 Unauthorized daughter card is plugged in—Turn off and remove the daughter card. 1. Remove the daughter card that you installed. 2. System board. 1804 Unauthorized WAN card is plugged in—Power off and remove the WAN card. 1. Remove the WAN card that you installed. 2.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 201x The solid state drive you have installed has not passed qualification for use in this computer. Using this drive may cause compatibility issues and potential issues with data integrity, including data loss. Press to continue.
Table 3. Error messages (continued) Symptom or error FRU or action, in sequence Thermal sensing error. System board. Cannot boot from any device. Check the status of device which you want to boot from. Device not found. 1. The device you want to boot from. 2. System board. Device Error. 1. The device you want to boot from. 2. System board. No valid operating system. 1. Check that the operating system has no failure and is installed correctly. 2. Reinstall the operation system. Excluded from boot order.
No-beep symptoms Table 5. No-beep symptoms Symptom or error FRU or action, in sequence No beep, power-on indicator on, LCD blank, and no POST. 1. Make sure that every connector is connected tightly and correctly. 2. DIMM. 3. System board. No beep, power-on indicator on, and LCD blank during POST. 1. Reseat DIMM. 2. System board. The power-on password prompt appears. A power-on password or a supervisor password is set. Type the password and press Enter. The hard-disk password prompt appears.
2. If no error is detected, do not replace any FRUs. 3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no more errors exist. Undetermined problems If the diagnostic tests did not identify the adapter or device that has failed, if wrong devices are installed, or if the system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects). Verify that all attached devices are supported by the computer.
52 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 5. Installing and configuring RAID This chapter presents following information about attaching SATA devices and configuring RAID for the RAID-supported models in this product. Note: When the BIOS was formatted or the system board was replaced in the RAID-supported models, RAID is enabled by default. Important notices for setting RAID: Before you install and configure RAID, make sure of the current RAID setting on the computer you are servicing.
1. Turn on the computer. 2. During the startup, when a prompt to press Ctrl+I to enter the Configuration Utility is displayed on the screen, press and hold the Ctrl key, and press the I key. 3. The screen for Intel Rapid Storage Technology option ROM is displayed. Select “Create RAID Volume” and press Enter. 4. Using the up and down arrow keys, Tab keys, and Enter key select the RAID level and fill in other fields. 5. Select “Create Volume” by pressing the Enter key.
Chapter 6. Status indicators This chapter presents the system status indicators that show the status of the computer.
Table 7. Status indicators Indicator 1 Speaker mute 2 Microphone mute 3 Wireless LAN, Wireless WAN, or WiMAX status 4 5 Bluetooth wireless or Wireless USB status Device access Meaning Orange: The speaker is on mute. To set the speakers on mute or unmute, press the speaker mute button. Orange: The microphone is on mute. None of the recording devices is available while the microphone mute is on by default. Green: The wireless LAN feature (the IEEE 802.11 b/g standard, 802.11 a/b/g, or 802.
Table 7. Status indicators (continued) Indicator 9 Caps lock 10 Sleep (standby for Windows XP) status 11 Battery status Meaning Green: Caps Lock mode is enabled. To enable or disable Caps Lock mode, press the Caps Lock key. Green: The computer is in sleep (standby) mode. Blinking green: The computer is entering sleep (standby) mode or hibernation mode, or is resuming normal operation. Green: The battery has more than 20% charge. Orange: The battery has between 5% and 20% charge.
58 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 7. Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 8. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock the computer. Fn+F3 Select a power plan (in Windows XP, power scheme) that has been created by Power Manager, or adjust the power level by using the slider control. When you press this combination, a panel for selecting a power plan (power scheme) appears.
Table 8. Fn key combinations (continued) Key combination Description Fn+F7 For Windows 7: Switch between the computer display and an external monitor. Windows will show these display options: • Computer display only (LCD) • Computer display and external monitor (same image) • Computer display and external monitor (extended desktop function) • External monitor only Note: To switch between the computer display and an external monitor, the Win+P key combination is also available.
Table 8. Fn key combinations (continued) Key combination Description Fn+End The computer display becomes dimmer. The purpose of this method is to change the brightness level temporarily. On Windows Vista, the default brightness level is loaded after sleep (standby), hibernation, reboot, or detaching or attaching an ac adapter. To change the default brightness level, change the settings of the Power Option in the Control Panel or use the Power Manager.
62 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 8. FRU replacement notices External CRU statement to customers: Some problems with your product can be resolved with a replacement part you can install yourself, called a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others are designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may request that Lenovo installs an Optional-service CRU according to the warranty service for your product.
• Torque driver If you have a torque driver, refer to the “Torque” column for each step. • Make sure that you use the correct screw. If you have a torque screwdriver, tighten all screws firmly to the torque shown in the table. Never use a screw that you removed. Use a new one. Make sure that all of the screws are tightened firmly. • Ensure torque screw drivers are calibrated correctly following country specifications.
MTM on rear label: TTTT-CTO S/N SSSSSSS Product ID on rear label: TTTT-MMM (Use this number when setting Serial Number) In the example, the Serial Number to be input is '1STTTTMMMSSSSSSS'. Retaining the UUID The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board. The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400.
66 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 9. Removing and replacing a FRU External CRU statement to customers: Some problems with your product can be resolved with a replacement part you can install yourself, called a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others are designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may request that Lenovo installs an Optional-service CRU according to the warranty service for your product.
Before servicing ThinkPad T510, T510i, and W510 Table 9. Removal steps of SIM card Some models of the ThinkPad T510, T510i, and W510 you are servicing might have the SIM card that the customer has installed. If the computer you are servicing has the SIM card, remove it before you start the servicing. To remove the SIM card, you need to remove the battery pack first. (See “1010 Battery pack” on page 68.) After you finish the servicing, make sure that you insert the card back into the slot firmly.
Table 10. Removal steps of battery pack (continued) 1 2 3 When installing: Install the battery pack in the slot, and then make sure that the battery latch is in the locked position. 1020 Serial Ultrabay Enhanced device or travel bezel For access, remove this FRU: • “1010 Battery pack” on page 68 Table 11.
1030 DIMM slot cover For access, remove this FRU: • “1010 Battery pack” on page 68 Table 12. Removal steps of DIMM slot cover Note: Loosen the screws 1 , but do not remove them.
Table 13. Removal steps of DIMM (bottom slot) a b 1 2 1 Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
Table 14. Removal steps of hard disk drive slot cover, HDD and HDD rubber rails or SSD and storage converter Note: Loosen the screw 1 , but do not remove it. 1 2 3 Table 15.
Table 16. Removal steps of SSD and storage converter 4 5 When installing: Make sure that the SSD connector or HDD connector is attached firmly. 1060 Keyboard For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1030 DIMM slot cover” on page 70 Table 17. Removal steps of keyboard 1 1 Step Screw (quantity) Color Torque 1 M2 × 14 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) Chapter 9.
Table 17. Removal steps of keyboard (continued) Push down the keyboard a little toward the arrow 2 until the front edge of the keyboard is detached from the keyboard bezel. 2 Lift the keyboard a little in the direction shown by arrow 3 , and then detach the connector 4 .
Table 18. Installation steps of keyboard 1. Attach the keyboard connector 1 . 1 2. Attach the keyboard so that the keyboard edges a are under the frame as shown in this figure. a a Chapter 9.
Table 18. Installation steps of keyboard (continued) 3. Gently press the keys with your thumbs and try to slide the keyboard toward you. 4. Make sure that the front side of the keyboard ( b ) is housed firmly. b b b 5. Secure the keyboard by tightening the screws from the bottom side of the computer.
Table 19. Removal steps of DIMM (upper slot) 1 2 1 Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). a b When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
Table 20. Removal steps of PCI Express Mini Card for wireless LAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. Note: Some models might have only two antenna cables in step 1 . 1 1 1 2 2 78 3 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.
Table 20. Removal steps of PCI Express Mini Card for wireless LAN (continued) 4 When installing: • In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN or M, and the black cable into the jack labeled AUX or A on the card. If the computer you are servicing has three cables, put the white cable in the cable protection tube as shown in this figure.
Table 21. Removal steps of PCI Express Mini Card for wireless WAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 1 1 2 2 3 80 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.
Table 21. Removal steps of PCI Express Mini Card for wireless WAN (continued) 4 When installing: Plug the orange cable into the jack labeled MAIN, and the blue cable into the jack labeled AUX on the card. 1100 Keyboard bezel assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1030 DIMM slot cover” on page 70 • “1060 Keyboard” on page 73 Attention: Before removing the keyboard bezel assembly, make sure that you have removed ExpressCard blank bezel or any card in the slot.
Table 22. Removal steps of ExpressCard blank bezel or ExpressCard (continued) 1 2 When installing: Make sure that the bezel or the card is correctly oriented as shown in this figure. Table 23. Removal steps of keyboard bezel assembly Note: The speaker assembly is attached to the keyboard bezel.
Table 23. Removal steps of keyboard bezel assembly (continued) 2 2 1 1 1 2 2 2 1 Step Screw (quantity) Color Torque 1 M2 × 4 mm, bind-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) 2 M2 × 14 mm, bind-head, nylon-coated (7) Black 0.181 Nm (1.85 kgfcm) 3 4 Chapter 9.
Table 23. Removal steps of keyboard bezel assembly (continued) 5 5 6 6 7 1110 Bluetooth daughter card (BDC-2.
Table 24. Removal steps of BDC-2.1 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly. 1120 Backup battery For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1030 DIMM slot cover” on page 70 • “1060 Keyboard” on page 73 • “1100 Keyboard bezel assembly” on page 81 DANGER Use only the battery specified in the parts list for your computer.
Table 25. Removal steps of backup battery 2 1 When installing: Make sure that the battery connector is attached firmly.
Table 26. Removal steps of Smart Card 3 3 4 1 2 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.85 kgfcm) 5 6 5 Chapter 9.
Table 27. Removal steps of dummy card and Contactless Smart Card 5 3 3 4 1 2 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.
Table 28. Removal steps of dummy card and spacer 3 1 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.85 kgfcm) 1140 Speaker assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1030 DIMM slot cover” on page 70 • “1060 Keyboard” on page 73 • “1100 Keyboard bezel assembly” on page 81 Chapter 9.
Table 29. Removal steps of speaker assembly 2 1 1 3 2 1 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.85 kgfcm) 5 4 5 4 4 5 5 5 4 When installing: Make sure that the speaker connector is attached firmly. Then route the cables and secure them properly as shown in the figure above.
1150 Thermal module For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1030 DIMM slot cover” on page 70 • “1060 Keyboard” on page 73 • “1100 Keyboard bezel assembly” on page 81 • “1140 Speaker assembly” on page 89 Table 30. Removal steps of thermal module 1 2 When installing: Make sure that the connectors are attached firmly. Note: Loosen the screws 4a to 4d in order, but do not remove them. Some models do not have screws 5 . For those models, skip the step 5 .
Table 30. Removal steps of thermal module (continued) 6 When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the parts marked a as in the following figures. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. For the new CPU thermal device/fan, you need to peel the thin film off from the rubbers marked b .
Table 30. Removal steps of thermal module (continued) For Integrated Graphics models: a For Workstation models: a a 1160 CPU For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1030 DIMM slot cover” on page 70 • “1060 Keyboard” on page 73 • “1100 Keyboard bezel assembly” on page 81 • “1140 Speaker assembly” on page 89 • “1150 Thermal module” on page 91 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Chapter 9.
Table 31. Removal steps of CPU Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU 2 . 2 1 a When installing: Place the CPU on the CPU socket, and then rotate the head of the screw in the direction shown by arrow a to secure the CPU.
Table 32. Removal steps of LCD unit 2 1 2 1 Step Screw cap 1 2 — Screw (quantity) Color Torque M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4.0 kgfcm) M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4.0 kgfcm) 3 3 Step Screw (quantity) Color Torque 3 M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4.0 kgfcm) Chapter 9.
Table 32. Removal steps of LCD unit (continued) 8 7 7 6 4 4 5 5 4 Step Screw (quantity) Color Torque 7 M2 × 4 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) When installing: • Make sure that you attach the LCD connector firmly. • Make sure that you route the cables firmly and tape up in the proper positions as shown in this figure. • When you route the cables, make sure that they are not subjected to any tension.
Table 32.
Table 33. Removal steps of base cover assembly 3 1 1 2 2 1 Step Screw (quantity) Color Torque 1 M2 × 7 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) 2 M2 × 14 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) 3 M2 × 4 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) 5 4 Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds.
13 FCC label 14 Homologation label 15 Serial number label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1020 Serial Ultrabay Enhanced device or travel bezel” on page 69 • “1030 DIMM slot cover” on page 70 • “1050 Hard disk drive slot cover, hard disk drive and HDD rubber rails or solid state drive and storage converter” on page 71 • “1060 Keyboard” on page 73 • “1080 PCI Express Mini Card for wireless LAN” on page 77 • “1090 PCI Express Mini Card for wireless WAN” on page 79 • “1100 Keyboard bezel assembly” on page 81 • “1110 Bluetoot
• • • • • • • • • • • • • • • “1050 Hard disk drive slot cover, hard disk drive and HDD rubber rails or solid state drive and storage converter” on page 71 “1060 Keyboard” on page 73 “1070 DIMM (upper slot)” on page 76 “1080 PCI Express Mini Card for wireless LAN” on page 77 “1090 PCI Express Mini Card for wireless WAN” on page 79 “1100 Keyboard bezel assembly” on page 81 “1110 Bluetooth daughter card (BDC-2.
Table 35. Location of major sensitive components on the system board Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. a MCP (Multi Chip Package) processor b PCH (Platform Controller Hub) c Accelerometer chip for the HDD Active Protection System™ d Graphics Note: d (Graphics) is only for the Switchable Graphics models and Workstation models.
Table 35. Location of major sensitive components on the system board (continued) For Workstation models: a d b c Table 36. Removal steps of system board and magnesium structure frame 2 3 2 2 1 1 Step Screw (quantity) Color Torque 1 Hex stud, nylon-coated (2) Silver 0.392 Nm (4.0 kgfcm) 2 M2 × 7 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) Chapter 9.
Table 36. Removal steps of system board and magnesium structure frame (continued) When installing: When you replace the system board, attach thermal rubbers as shown in this figure. Depend on the models you are servicing, the number of thermal rubbers are different. Check the thermal rubbers on the old system board, and find duplicates of them in the new FRU package and apply them to the new system board.
Table 37. Removal steps of LCD bezel assembly (continued) 2 2 2 2 2 2 2 2 3 When installing: Make sure that all the latches are attached firmly. 2020 LED sub card For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “2010 LCD bezel assembly” on page 104 Table 38. Removal steps of LED sub card Note: Some models do not have connector 1a . 2 1a 1 When installing: Make sure that the connectors are attached firmly and the card is installed as shown in this figure. Chapter 9.
2030 Integrated camera For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “2010 LCD bezel assembly” on page 104 Table 39. Removal steps of integrated camera 1 3 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector of the integrated camera is attached firmly.
• • “1170 LCD unit” on page 94 “2010 LCD bezel assembly” on page 104 Table 40. Removal steps of LCD cable, camera cable, LCD panel, and hinges In step 1 , release the antenna cables from the left and right hinges. 1 1 2 2 2 2 Step Screw (quantity) Color Torque 2 M2.5 × 6 mm, wafer-head, nylon-coated (4) Black 0.392 Nm (4.0 kgfcm) When installing: When attaching the LCD panel to the cover, press the left and right edges covered with metal gently with your fingers.
Table 40. Removal steps of LCD cable, camera cable, LCD panel, and hinges (continued) 3 4 5 5 5 6 7 8 When installing: Make sure that the LCD cable connector is attached firmly.
Table 40. Removal steps of LCD cable, camera cable, LCD panel, and hinges (continued) 9 10 9 9 10 9 Step Screw (quantity) Color Torque 9 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.
Table 41. Removal steps of antenna kit and LCD rear cover assembly (continued) Cable routing: When you install the antenna kit, route the cables as shown in the figures below. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
Chapter 10. Locations This chapter presents the location of ThinkPad T510, T510i, and W510 features and hardware. Front view 1 Status indicators Note: For the description of each indicator, see Chapter 6 “Status indicators” on page 55.
1 2 3 4 2 21 8 20 18 5 17 6 16 19 7 15 8 14 9 13 10 12 11 Rear view 1 Status indicators Note: For the description of each indicator, see Chapter 6 “Status indicators” on page 55.
1 2 11 3 10 4 5 6 9 7 8 Bottom view 1 Battery pack 2 Battery pack latch 3 Docking connector 4 Solid state drive (SSD) or hard disk drive (HDD) slot 5 DIMM slot (bottom) 6 LCD cover latch 7 Serial Ultrabay Enhanced lock latch 8 Serial Ultrabay Enhanced eject latch 1 8 7 2 3 6 5 4 Chapter 10.
114 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Chapter 11. Parts list This chapter contains following lists of the service parts. • “Overall” on page 116 • “LCD FRUs” on page 169 • “Keyboard” on page 192 • “Miscellaneous parts” on page 193 • “AC adapters” on page 195 • “Power cords” on page 195 • “Recovery discs” on page 196 • “Common service tools” on page 204 Notes: • Each FRU is available for all types or models, unless specific types or models are specified.
Overall 24 23 1 2 22 d a 3 c b 21 20 4 5 19 18 6 17 16 7 8 15 9 14 10 13 7 12 11 116 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Table 42. Parts list—Overall No. FRU (Overall) FRU no. CRU ID ad See “Miscellaneous parts” on page 193. 1 LCD unit (see “LCD FRUs” on page 169.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No.
Table 42. Parts list—Overall (continued) No.
Table 42. Parts list—Overall (continued) No.
Table 42. Parts list—Overall (continued) No.
Table 42. Parts list—Overall (continued) No.
Table 42. Parts list—Overall (continued) No.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) 9 134 Battery pack, Li-ion (6 cell), 2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) 9 Battery pack, Li-ion (6 cell), 2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) 9 136 Battery pack, Li-ion (6 cell), 2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 9 Battery pack, Li-ion (6 cell), 2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 9 Battery pack, Li-ion (6 cell), 10.4 Wh • 4313-CTO • 4314-CTO • 4339-CTO • 4349-CTO • 4384-CTO • 4484-CTO • 4873-CTO 42T4819 * 9 Battery pack, Li-ion (9 cell), 2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 9 Battery pack, Li-ion (9 cell), 2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 14 SATA solid state drive, 1.8", 80 GB • 4313-CTO • 4314-CTO • 4339-CTO • 4349-CTO, 4Bx • 4384-CTO, 4Bx • 4484-CTO • 4873-CTO • 4318-CTO • 4319-CTO • 4387-CTO • 4389-CTO • 4391-CTO • 4875-CTO • 4876-CTO 45N8017 ** 14 SATA solid state drive, 2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 14 SATA solid state drive, 1.8", 128 GB • 4313-CTO • 4314-CTO, 56x, 58x, 7Rx • 4339-CTO • 4349-CTO, 3Hx, G4x, G7x • 4384-CTO, G4x • 4484-CTO • 4873-CTO • 4318-CTO • 4319-CTO, 2Ex, 2Tx, 2Xx, 3Ex, 3Jx • 4387-CTO • 4389-CTO • 4391-CTO • 4875-CTO • 4876-CTO 45N8203 ** 14 SATA solid state drive, 2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 14 SATA solid state drive, 2.5", 128 GB • 4313-CTO • 4314-CTO, 56x, 58x, 7Rx • 4339-CTO • 4349-CTO, 3Hx, G4x, G7x • 4384-CTO, G4x • 4484-CTO • 4873-CTO • 4318-CTO • 4319-CTO, 2Ex, 2Tx, 2Xx, 3Ex, 3Jx • 4387-CTO • 4389-CTO • 4391-CTO • 4875-CTO • 4876-CTO 45N8029 ** 14 SATA solid state drive, 1.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 14 SATA solid state drive, 1.8", 256 GB, FDE • 4313-CTO • 4314-CTO • 4339-CTO • 4349-CTO • 4384-CTO • 4484-CTO • 4873-CTO • 4318-CTO • 4319-CTO • 4387-CTO • 4389-CTO • 4391-CTO • 4875-CTO • 4876-CTO 45N7959 ** 14 SATA solid state drive, 1.8", 256 GB, FDE • 4313-CTO • 4314-CTO • 4339-CTO • 4349-CTO • 4384-CTO • 4484-CTO • 4873-CTO • 4318-CTO • 4319-CTO • 4387-CTO • 4389-CTO • 4391-CTO • 4875-CTO • 4876-CTO 45N8207 ** 15 1.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 17 CPU assembly, Intel Core™ i3-330M Processor (2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 17 CPU assembly, Intel Core i5-450M Processor • 4313-CTO, A3x, A4x, AVx, AWx, AXx • 4314-CTO, 9Ex, 9Ux, 9Vx, AFx, AGx, AHx, AJx, AKx, ALx, C6x, C7x, CNx, D4x • 4339-CTO, BFx, BGx • 4349-CTO • 4384-CTO • 4484-CTO • 4873-CTO 75Y4906 N 17 CPU assembly, Intel Core i5-460M Processor (2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. 17 CPU assembly, Intel Core i5-560M Processor (2.66 GHz) • 4313-CTO, CTx • 4314-CTO, CJx, CKx, D5x, D6x, D7x, DDx, DEx, DFx, DGx, DHx, DLx, DMx, DNx • 4339-CTO • 4349-CTO, GAx, GDx, GHx, GJx • 4384-CTO, GGx, GKx, GJx • 4484-CTO • 4873-CTO • 4318-CTO • 4319-CTO, 5Xx, 63x, 65x, 66x • 4387-CTO • 4389-CTO • 4391-CTO • 4875-CTO • 4876-CTO 04W0338 N 17 CPU assembly, Intel Core i5-580M Processor (2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. 17 CPU assembly, Intel Core i7-640M Processor (2.80 GHz) • 4313-CTO • 4314-CTO • 4339-CTO • 4349-CTO • 4384-CTO • 4484-CTO • 4873-CTO 04W0307 N 17 CPU assembly, Intel Core i7-720QM Processor (1.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 18 Bluetooth daughter card (BDC-2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
1 2 3 10 9 8 4 5 6 7 170 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Table 43. Parts list—15.6-inch HD LED-backlight LCD No. FRU (15.6-inch HD LED-backlight LCD) FRU no.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no. CRU ID 10 LCD module, 15.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no. CRU ID 10 LCD module, 15.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no. CRU ID 10 LCD module, 15.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no. CRU ID 10 LCD module, 15.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD No. FRU (15.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.6-inch HD+ LED-backlight LCD) 2 180 Integrated camera (2.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.6-inch HD+ LED-backlight LCD) FRU no.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.6-inch HD+ LED-backlight LCD) FRU no.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.6-inch HD+ LED-backlight LCD) FRU no. CRU ID 10 42T0743 N 186 LCD module, 15.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.6-inch HD+ LED-backlight LCD) FRU no. CRU ID 10 42T0763 N FRU no. CRU ID 60Y5482 N LCD module, 15.
Table 45. Parts list—15.6-inch FHD LED-backlight LCD (continued) No. FRU (15.6-inch FHD LED-backlight LCD) FRU no. CRU ID 2 Integrated camera (2.
Table 45. Parts list—15.6-inch FHD LED-backlight LCD (continued) No. FRU (15.6-inch FHD LED-backlight LCD) FRU no.
Table 45. Parts list—15.6-inch FHD LED-backlight LCD (continued) No. FRU (15.6-inch FHD LED-backlight LCD) FRU no.
Table 46. Parts list—15.6-inch FHD LED-backlight LCD with Multi touch panel No. FRU (15.6-inch FHD LED-backlight LCD with Multi touch panel) FRU no. CRU ID 1 LCD front bezel assembly (touch panel) • 4318-CTO • 4319-CTO, 2Rx, 2Dx, 34x, 38x, 3Cx, 3Px, 4Ax, 4Gx, 4Lx, 4Wx, 4Xx, 57x • 4389-CTO, 2Cx, 2Hx, 2Ux, 37x, 3Bx, 3Lx, 3Mx • 4391-CTO • 4875-CTO • 4876-CTO 60Y5483 N 2 Integrated camera (2.
Table 46. Parts list—15.6-inch FHD LED-backlight LCD with Multi touch panel (continued) No. FRU (15.6-inch FHD LED-backlight LCD with Multi touch panel) FRU no. CRU ID 10 LCD module, 15.6-inch FHD LED-backlight, with touch panel • 4318-CTO • 4319-CTO, 2Rx, 2Dx, 34x, 38x, 3Cx, 3Px, 4Ax, 4Gx, 4Lx, 4Wx, 4Xx, 57x • 4389-CTO, 2Cx, 2Hx, 2Ux, 37x, 3Bx, 3Lx, 3Mx • 4391-CTO • 4875-CTO • 4876-CTO 13N7298 N 10 LCD module, 15.
Table 47. Parts list—Keyboard (continued) Language FRU no. Norwegian 45N2091 45N2161 45N2231 Polish 45N2092 45N2162 45N2232 Portuguese 45N2093 45N2163 45N2233 Russian 45N2094 45N2164 45N2234 Slovak 45N2095 45N2165 45N2235 Slovenian 45N2096 45N2166 45N2236 Spanish 45N2081 45N2151 45N2221 Swiss 45N2098 45N2168 45N2238 Thai 45N2105 45N2175 45N2245 Traditional Chinese 45N2104 45N2174 45N2244 Turkish 45N2099 45N2169 45N2239 Turkish F 60Y9552 60Y9554 60Y9550 U.K.
Table 48. Parts list—Miscellaneous parts (continued) FRU FRU no.
AC adapters Table 49. Parts list—2-pin ac adapters FRU FRU no.
Table 52. Parts list—2-pin power cords Region P/N Argentina • models -CTO, xxY 42T5020 42T5105 Brazil • models -CTO, xxP 42T5180 42T5183 Canada, U.S. • models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan • models -CTO, xxE, xxJ 42T5014 42T5099 CRU ID * Table 53. Parts list—3-pin power cords Region P/N Australia, New Zealand • models -CTO, xxG, xxM 42T5050 42T5135 Bangladesh, Sri Lanka, South Africa • models -CTO, xxG 42T5056 42T5141 Canada, U.S.
• 4314-CTO, 2Kx, 2Lx, 2Nx, 3Dx, 3Ex, 3Hx, 3Jx, 3Mx, 3Nx, 3Rx, 3Sx, 3Vx, 3Wx, 3Zx, 42x, 45x, 46x, 49x, 4Ax, 4Dx, 4Ex, 4Ux, 4Vx, 4Yx, 4Zx, 5Hx, 6Zx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 7Bx, 7Cx, 7Nx, 7Px, 7Xx, 7Yx, 8Qx, 9Ex, 9Hx, 9Jx, 9Mx, 9Nx, 9Rx, 9Sx, A8x, AYx, D6x • 4339-CTO • 4349-CTO, 3Xx, 4Nx, 4Px, 42x, 48x • 4384-CTO, 43x, 44x, 45x, 46x, 47x • 4484-CTO • 4873-CTO • 4318-CTO • 4319-CTO, 27x, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Cx, 5Tx, 5Ux, 5Vx, 5Wx • 4387-CTO • 4389-CTO, 27x, P4x • 4391-
• • • • • • • • • • 4384-CTO 4484-CTO 4873-CTO 4318-CTO 4319-CTO 4387-CTO 4389-CTO 4391-CTO 4875-CTO 4876-CTO Table 55.
• • • • • • 4319-CTO 4387-CTO 4389-CTO 4391-CTO 4875-CTO 4876-CTO Table 57.
Table 58. Parts list—Windows 7 Home Premium (32 bit) recovery DVDs (continued) Language P/N English, French, German, and Italian (in Switzerland) 58Y4422 French 58Y4406 German 58Y4407 Hebrew 58Y4408 Japanese 58Y4410 Korean 58Y4411 Norwegian 58Y4412 Polish 58Y4413 Russian 58Y4415 Russian (English-enabled) 58Y4414 Simplified Chinese 58Y4403 Spanish 58Y4416 Traditional Chinese 58Y4404 Traditional Chinese (Hong Kong S.A.R.
Table 59. Parts list—Windows 7 Home Premium (64 bit) recovery DVDs (continued) Language P/N Hungarian 58Y4511 Japanese 58Y4512 Polish 58Y4513 Portuguese 58Y4514 Romanian 58Y4515 Serbian-Latin 58Y4519 Simplified Chinese 58Y4505 Slovak 58Y4516 Slovenian 58Y4517 Spanish 58Y4518 Traditional Chinese (Hong Kong S.A.R.
Table 60.
• • • • • • • • • • • • CNx, CZx, D3x, D4x, D7x, D8x, D9x, DAx, DBx, DCx, DDx, DEx, DMx, DPx, DQx, DRx, DSx, DTx, DVx, DWx, DXx, DYx, DZx 4339-CTO, BHx, BJx, BLx, BMx 4349-CTO, 3Lx, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Qx, 4Vx, 4Wx, 4Yx, 52x, 53x, 54x, 5Cx, 5Dx, 5Ex, 5Kx, G2x, G3x, G4x, G5x, G6x, G7x, G8x, G9x, GAx, GBx, GCx, GDx, GJx 4384-CTO, 5Cx, 5Dx, 5Ex, H2x, H3x, G4x, G5x, G6x, GEx, GFx, GGx, GKx, GJx 4484-CTO 4873-CTO 4318-CTO 4319-CTO, 24x, 25x, 29x, 2Cx, 2Dx, 2Ex, 2Px, 2Qx, 2Rx, 32x, 34x, 39x, 3Ax, 3Bx, 3Cx
Table 61. Parts list—Windows 7 Professional (64 bit) recovery DVDs (continued) Language P/N Spanish 58Y4444 Traditional Chinese 58Y4424 Traditional Chinese (Hong Kong S.A.R.) 58Y4431 Turkish 58Y4446 CRU ID Common service tools Table 62. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4" drive spinner handle 1650840 1/4" Sq. to 1/4" hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Active Protection System Lenovo Rescue and Recovery ThinkLight ThinkPad ThinkVantage TrackPoint Ultrabay UltraNav IBM (used under license) is trademark of the International Business Machines Corporation in the United States, other countries, or both.
Part Number: 63Y0536_03 (1P) P/N: 63Y0536_03 *63Y0536_03*
