Owner manual

ManualsBrandsLennox Hearth ManualsToolsVIN

Report No. 50-S-11b-5

INSTALLATION AND OPERATION MANUAL

WARNINGS

•

Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will

retain heat for a while after shutting off the appliance. Severe burns may result.

•

Carefully supervise children in the same room as appliance.

Do not store or use gasoline or other ﬂammable

vapors or liquids in the vicinity of this or any other

appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not light any appliance.

• Do not touch any electrical switch; do not

Use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow your gas supplier's

instructions.

• If your gas supplier cannot be reached, call

the ﬁre department.

Installation and service must be performed by a quali-

ﬁed installer, service agency or the gas supplier.

Ne pas entreposer ni utiliser d’essence ou d’autres produits

ou liquides inﬂammables à proximité de cet appareil ou

de tout autre appareil de chauffage.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer l’appareil.

• Ne pas toucher aux interrupteurs électriques; ne pas

utiliser un téléphone dans le bâtiment.

• Aller immédiatement chez un voisin pour téléphoner

au fournisseur du gaz et suivre leurs instructions.

• Si le fournisseur de gaz n’est pas disponible, appeler

les pompiers.

L’installation et l’entretien doivent être assurés par un

installateur certiﬁé, une société de service spécialisée

ou le fournisseur de gaz.

WARNING: If the information in these instructions

are not followed exactly, a ﬁre or explosion may

result causing property damage, personal injury

or loss of life.

AVERTISSEMENT : S’assurer de bien suivre les instruc-

tions données dans ce guide pour minimiser les risques

d’incendie ou d’explosion pouvant entraîner des dom-

mages matériels, des blessures ou la mort.

•

Suitable for installation into masonry or factory built ﬁreplaces. These appliances may be installed in an after-

market permanently located, manufactured (mobile) home (USA only), where not prohibited by local codes. This

appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible

for use with other gases unless a certiﬁed kit is used.

•

Lennox Hearth Products gas-burning appliances are designed for use as a supplemental heater. They are not

intended for continuous use as a primary heat source.

Vintage™ (VIN)

In the Commonwealth of Massachusetts:

• Installation must be performed by a licensed plumber or gas tter

• See Table of Contents for location of additional Commonwealth of

Massachusetts requirements

Portland

RAFT

Direct-Vent

Gas Stove

Retain These Instructions For Future Reference

A French manual is available upon request. Order P/N 775,227CF.

Ce manuel d’installation est disponible en francais, simplement

en faire la demande. Numéro de la pièce 775,227CF.

P/N 775,227M Rev. D, 11/2008

Summary of content (28 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL Direct-Vent Gas Stove Retain These Instructions For Future Reference P/N 775,227M Rev. D, 11/2008 A French manual is available upon request. Order P/N 775,227CF. Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la pièce 775,227CF.
PAGE 2
IMPORTANT SAFETY AND WARNING INFORMATION  FOR YOUR SAFETY do not install or operate your Vintage™ gas stove without first reading and understanding this manual. Any installation or operation of the appliance deviating from that which is stated in this manual WILL void the warranty and may be hazardous.  INSTALLATION AND REPAIR SHOULD ONLY BE DONE BY A QUALIFIED SERVICE TECHNICIAN. DO NOT ATTEMPT TO SERVICE THE APPLIANCE YOURSELF.
PAGE 3
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW GAS APPLIANCE MANUFACTURED BY LENNOX HEARTH PRODUCTS. When you purchased your new gas stove, you joined the ranks of thousands of individuals whose answer to their home heating needs reflects their concern for efficiency and our environment. We extend our continued support to help you achieve the maximum benefit and enjoyment available from your new gas stove.
PAGE 4
ORIFICE SIZE/ALTITUDE ADJUSTMENT For altitudes above 2,000 feet (In Canada 4,500 FT/1370 M),the orifice should be de-rated by 4% for every 1,000 feet to maintain the proper ratio of gas to air. Improper orifice sizing may result in damage and unsafe conditions. Changing the orifice should only be done by a qualified service technician. Contact your Lennox Hearth Products dealer for proper orifice sizes.
PAGE 5
Millivolt Valve PRE-INSTALLATION This stove is operated with a millivolt valve and therefore burns even during a power outage. Features Fuel Installation Options This stove comes from the factory equipped to burn natural gas at a specified elevation. The stove can be converted to burn LP gas (liquid propane) by changing the cassette (valve and pilot assembly) or installing a conversion kit. Only Lennox Hearth Products conversion kits can be used to convert from NG to LP or LP to NG.
PAGE 6
Preparing Your Vintage™ Stove For Installation Dimensions Read all instructions before beginning your installation. If instructions have not been read carefully, your installation could void your warranty and may create a serious fire, health, or other safety hazard. The gas line screws into the gas valve at the back of the stove 5” in from the right side of the stove and 4-3/16” up from the base of the unit.
PAGE 7
Clearances to Combustibles Alcove dimensions Minimum clearances to combustible materials shown here are in inches (millimeters). See Page 6 for pipe clearances. The minimum width between alcove side walls is 30-1/2” (775mm). The glass door lifts up to access the firebox on the stove. Therefore, if the stove is to be installed in an alcove, the alcove needs to be constructed to allow for removal of the glass door.
PAGE 8
INSTALLATION Baffle and Log Set Installation Baffle The cast iron baffle is wrapped in foam and shipped between the outside of the firebox and the outer shell of the stove. Remove the foam and install the baffle in the rectangular hole in the top of the firebox. The baffle rests unsecured in the hole. Figure 10 Log Set and Embers Firebox Accessories / Parts Cat. No.
PAGE 9
Side-Insert Installation Follow these steps to install the cast iron inserts or your own custom stone inserts in the Vintage™ gas stove: 1. Remove the cast iron top and set it aside. 2. Remove the cast iron upper piece A - see Figure 14. Complete this step by unscrewing the (2) 5/32 hex-head screws labeled B in Figure 17. Lift out the upper cast piece A with the retaining bracket D attached. 3. Slide the cast iron or stone side inserts (size 15.5”x 10.
PAGE 10
Vent Installation Minimum Components for Horizontal Installation: Venting: The Vintage™ gas stove has been tested and listed as a direct vent heater system by OMNI-Test Laboratories, Beaverton, Oregon and is recommended for use with Security™ Secure Vent pipe*. Horizontal Termination Kit which includes: Important: • Read all instructions carefully before starting the installation. Failure to follow these instructions may create a fire or other safety hazard and will void the warranty.
PAGE 11
Vent Parts List Horizontal Vent Installation Direct vent pipe Security™ Secure Vent™ * may be used with the Vintage™ gas stove. Please see the lists below to verify the components available from each direct vent pipe manufacturer. Snorkel terminations are available for applications which may require vertical rise on the building exterior. The components listed below come in a galvanized finish. Most of the components are also available in a painted black finish.
PAGE 12
Snorkel Terminations For installations requiring a vertical rise on the exterior of the building, 14-inch and 36-inch tall snorkel terminations are available. When using a snorkel, the stove can be vented directly out the back. There is a vent starter collar fastened to the stove (to vent straight out the back), remove the four screws securing the collar, rotate the collar 180 degrees and refasten using the same four screws.
PAGE 13
Flue Restrictors The flue restrictor settings shown in Figures 26 and 27 are for typical installations and may need to be adjusted from standard to take into account other variables in the installation to achieve proper combustion. See Flue Restrictor Guidelines on this page to assist you in making a proper flue restrictor adjustment. The Vintage™ gas stove uses balanced flue technology to ensure proper combustion. A flue restrictor may need to be installed depending on the vent configuration of your stove.
PAGE 14
Vertical Terminations Horizontal Terminations The shaded areas in the diagram below show all allowable combinations of vent configurations with horizontal terminations. Horizontal sections of pipe require 1/4” of rise for every 12” of run. A second 90 degree or 45 degree elbow (in addition to the first 90 degree elbow at the top of the vertical length of pipe) is allowed as long as the overall length of the horizontal run of pipe does not exceed those shown below. Use the restrictor positions indicated.
PAGE 15
Exterior Horizontal Vent Termination Clearance Requirements * See Item D in the Text Below. Center Line Exterior Wall of Termination Inside Corner Detail *18” Horizontal Termination G 18” V Ventilated Soffit A Inside Corner = 9" in U.S. A = 12" in Canada DETAIL D H 3 ft. B L V C V F Fixed Closed Window V C C A Operable Window V C V B D X V 3 ft.
PAGE 16
Gas Line Installation This stove must be connected to the gas line in accordance with local codes and/or the National Fuel Gas Code, ANSI Z223.1 (In Canada, the current CAN/CSA B149.1 installation code). The gas line screws into the gas valve at the back of the stove 5” in from the right side of the stove and 4 3/16” up from the base of the unit. After connecting the gas line, all joints in the line and connections at the valve should be checked for leaks.
PAGE 17
Operating Instructions Pre-Lighting Checklist Be sure to check these items before the initial lighting of the stove: c The stove gas label corresponds to the gas supply available - that is “natural gas” for natural gas or “LP gas” for LP gas. c Gas pressure has been checked carefully - see Page 16. c All gas fittings have been checked for leaks. c All clearances to combustibles have been met - see Pages 6 and 7. c All combustible materials have been removed from area in front of the stove.
PAGE 18
TO TURN OFF GAS TO APPLIANCE Gas Control Knob (Pilot / On / Off) Flame Height Control Knob (HI/LO) 1. Turn off the "ON/OFF" rocker switch and/or thermostat (if installed) to its lowest setting. 2. Turn off electric power to the appliance if service is to be performed. 3. Push in gas control knob slightly and turn clockwise to "OFF." Do not force. This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
PAGE 19
Air Shutter Adjustment The air shutter control lever is located on the bottom of the stove directly to the left of the gas valve. The lever is linked to the primary air shutter on the main burner. The air shutter regulates the amount of primary air the burner receives and therefore how clean the stove burns. The air shutter should only be adjusted by a qualified gas technician. The stove should burn for about 15 minutes with the logs installed before adjusting the air shutter.
PAGE 20
Operating Options “On-Off” Switch, Thermostat Or Remote Control Your stove comes equipped with an “On/Off” rocker switch used to turn the burner on and off while the pilot light is on. The switch is a round rocker switch located behind the main control panel door. A millivolt wall thermostat, or a remote control, can be used to supplement the rocker switch. The gas valve is powered by millivolts generated by the pilot assembly.
PAGE 21
MAINTENANCE AND SERVICING Maintenance Checklist: The following should only be performed by a qualified service technician. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. 1. Annual inspection should be made and the following checks performed: o When unit is cool, open glass viewing door and inspect burner for dirt, soot and lint accumulations and remove if necessary.
PAGE 22
General Vent Pipe Maintenance Glass/Door Maintenance Conduct an inspection of the venting system semi-annually. Recommended areas to inspect are as follows: 1. Check areas of the venting system which are exposed to the elements for corrosion. These will appear as rust spots or streaks and in extreme cases, holes. These component should immediately be replaced. 2. Remove the cap and shine a flashlight down the vent. Remove any bird nests or other foreign material. 3.
PAGE 23
TROUBLESHOOTING NOTE: When troubleshooting the gas control system, be sure the external gas shut off valve, located at the gas supply inlet is in the “ON” position. IMPORTANT: Call your gas supplier or plumber for additional help with any gas control problem. Valve system troubleshooting should only be accomplished by a qualified service technician. SYMPTOM Thin black coating (soot) forms on the viewing glass, logs, or firebox. Humming or whistling coming from fireplace.
PAGE 24
REPLACEMENT PARTS Vintage™ Model VIN Part Number H6031 H5936 H5947 H2830 H5942 H5943 H5945 H5955 H5962 H5944 75190 75191 H5877 H5875 H5744 H3108 H5745 H5882 H5883 H5660 H5861 H5863 H5864 H5865 H3082 H5518 H5854 H5920 H5848 H5849 H5855 H5850 H5845 H5851 H5852 H5853 H5915 70K99 24 Description Cassette Assembly, NG (if LP, also requires 75190 Conversion Kit) Burner Assembly Pilot Assembly NG Pilot Assembly LP Gas Control Valve, NG (if LP, also requires H5945 LP Regulator) Regulator, NG Regulator, LP O
PAGE 25
ACCESSORIES Misc. Cat. No. Panel Kits (Required) Cat. No. Model 75199 VINT-CPS-B H7406 VINTAGE-PK-BG Model Description 75194 VINT-TET BLWR Blower 75195 VINT-TETN-MHK Mobile Home Install Kit Cast Iron Panel Set/Black, Reversible u 75203 VINT-RVTC Gallo Veneziano Stone Panels 70005 RT-AC H0251 RCL-STAT Remote Thermostat, Deluxe (Timer, T-Stat, Clock) H4635 DWTK Digital Wall Thermostat Kit Description Gas Conversion Kits Cat. No.
PAGE 26
SAFETY / LISTING LABEL MODEL MODÈLE SERIAL NO. Vintage™ HOMOLOGUÉ FOYER RADIANT PRÉFABRIQUÉ AU GAZ -NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE VIN MANUFACTURED BY / FABRIQUÉ PAR: LENNOX HEARTH PRODUCTS PO BOX 987 AUBURN, WA., USA 98071 Report No. / Número de Rapport 50-S-11b-5 MAY BE INSTALLED IN RESIDENTIAL BEDROOMS AND MANUFACTURED (MOBILE) HOMES. TESTÉ SELON LA NORME ANSI Z21.88-2005/CSA 2.33-2005 «FOYER RADIANT AU GAZ», UL307B, CSA P.4.1-02, ET CGA 2.17-M91. FACTORY EQUIPPED FOR NATURAL GAS.
PAGE 27
LIGHTING LABEL FOR YOUR SAFETY READ BEFORE OPERATING POUR VOTRE SÉCURITÉ, LIRE AVANT L’ALLUMAGE WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING AVERTISSEMENT: SI VOUS NE RESPECTEZ PAS RIGOUREUSEMENT LES INSTRUCTIONS CI-DESSOUS, VOUS POURRIEZ ENCOURIR UN RISQUE D’INCENDIE ET/OU A. B. A. Cet appareil utilise un système d’allumage par étincelle (allumeur Piézo-électrique) pour allumer la veilleuse.
PAGE 28
Warranty Your gas stove is covered by a limited warranty (provided with appliance). Please read the warranty to be familiar with its coverage. Retain this manual. File it with your other documents for future reference. Product reference information We recommend that you record the following important information about your appliance. Please contact your Lennox Hearth Products dealer for any questions or concerns. For the number of your nearest Lennox Hearth Products dealer, please call 1-800-9-LENNOX.