IMPORTANT INSTRUCTIONS - READ AND SAVE THESE INSTRUCTIONS MOBILE OUTDOOR PIZZA OVEN WARNING Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read this instruction manual thoroughly before installing or servicing this equipment. Owner’s Manual WARNING 1. Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance. 2.
OVEN OPERATION 1-2-3 Before Cooking: Step 1. Keep your oven a safe distance away from your property.* Step 2. Always perform a leak test.* Step 3. Keep children away from the oven. During Cooking: (To avoid tripping safety valves, please follow these instructions carefully!) Step 1. Turn gas tank on slowly. Step 2. Use protective gloves when oven gets hot. After Cooking: Step 1. Burn oven for 10-15 minutes to burn off food residue. Step 2. Wait until the oven is completely cooled before closing oven door.
TABLE OF CONTENT Safety Information................................................................................................................4 Package Contents................................................................................................................6 Hardware Contents..............................................................................................................7 Preparation............................................................................................
!"#$%&'()#*+,"%(*) "#$%&'$()*+,--,+(.)$./$+&(*$,00-(,)1'$23*+$1.)/.42$5(+&$-.1,-$1.6'*$.47$()$+&'$,8*')1'$./$-.1,-$1.6'*7$5(+&$ '(+&'4$+&'$9,+(.),-$:3'-$;,*$<.6'7$=9>?$@AAB#"C9:D=$E!7$.4$D4.0,)'$?)*+,--,+(.)$<.6'7$<>=C<;=FG"!H#"# A#$%&(*$.I')$(*$()+')6'6$/.4$3*'$.3+6..4*$,)6$*&.3-6$).+$8'$3*'6$()$,$83(-6()J7$J,4,J'$.4$,)K$.+&'4$')1-.*'6$ .4$1.I'4'6$,4',# B#$%&(*$.3+6..4$.I')$(*$).+$()+')6'6$/.4$()*+,--,+(.)$()$.4$.)$4'14',+(.)$I'&(1-'*$,)6C.4$8.,+*# !#$=$2()(232$1-',4,)1'$./$L"$12$MA!$()1&'*N$/4.2$1.
SAFETY INFORMATION 16. The cylinder used must include a collar to protect the cylinder valve. 17. Do not store a spare LP-gas cylinder under or near this appliance. 18. Never fill the cylinder beyond 80 percent full. 19. If the information in “17” and “18” is not followed exactly, a fire causing death or serious injury may occur. 20.
PACKAGE CONTENTS A B C D E F G PART A B C D E F G DESCRIPTION Main Body Cooking Grill Pizza Stone Bottom Grill Fat Cup Assy Smoker Box Assy Flame Tamer QUANTITY 1 2 1 1 1 1 1 6
ASSEMBLY INSTRUCTIONS The following list is included inside the pizza oven carton: Battery 1 pc The following list is not included inside the pizza oven carton, but needed when the user is assembling the pizza oven.
ASSEMBLY INSTRUCTIONS PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. 1. Use screw M6*40×2 pcs, nut M6×2 pcs and flat washer 18*6.4*1x2pcs to fix the weight under the base panel. 2. Use screw M6*12×16 pcs to attach swivel castor with lock×2 pcs and fixed castor×2 pcs onto the bottom of the base panel.
ASSEMBLY INSTRUCTIONS 3. Use screw M6*12×2 pcs to fix the left side panel onto the base panel of the stand. 4. Use screw M6*12×2 pcs to fix the right side panel onto the base panel of the stand. 5. Use screw M4*10×4 pcs and nut M4×4 pcs to attach the transformer assembly onto the outside of the back panel of the stand.
ASSEMBLY INSTRUCTIONS 6. Use screw M6*12×5 pcs to attach the stand base panel onto the base panel, between the two side panels. 7. Use screw M4*10×4 pcs to fix the stand door horizontal beam between the two side panels. Note: Please fasten the upper two screws first, and then the lower two screws. 8. Use screw M4*10×4 pcs to fix the stand top panel on the top of the two side panels and back panel.
ASSEMBLY INSTRUCTIONS 9. Use screw M5*10×8 pcs to attach triangle×2 pcs on the bottom of the base panel, leaning against the two side panels. 10. Use screw M3*12×2 pcs and nut M3×2 pcs to attach the door magnet onto the right side panel. 11. First, insert the door lower axis into the hole in the base panel. Next, push down the door upper spring axis and let go of the spring when it is pointed to the hole in the horizontal beam.
ASSEMBLY INSTRUCTIONS 12. Put the oven assembly on the stand-top panel. Use screw M6*12×4 pcs to fasten the oven onto the stand. 13. Use screw M5*10×16 pcs to attach side shelf bracket×4 pcs onto the drawer side panels. Using one of the screw M5*10 to fix the match holder onto the front bracket of right side shelf. 14. Use screw M6*12×8 pcs and special nut TB31-05-03×8 pcs to hang side shelf×2 pcs onto the four brackets.
ASSEMBLY INSTRUCTIONS 15. Use screw M4*8×3 pcs to fix the chimney assembly onto the top of the oven exterior. 16. Use screw M5*35×4 pcs to fix the back heat shield onto the back panel of the oven.
ASSEMBLY INSTRUCTIONS 18. Insert the fat cup into the back of the oven. Your complete pizza oven is now assembled.
CARE AND MAINTENANCE L.P. GAS INSTALLATION Gas grills that are set to operate with L.P. gas come with a high capacity hose and regulator assembly. (Note: Only use the pressure regulator and hose assembly supplied with the grill or a replacement pressure regulator and hose assembly specified by the manufacturer). This assembly is designed to connect directly to a standard 9 kg (20 lb.) L.P. cylinder. L.P. cylinders are not included with the grill. L.P.
CARE AND MAINTENANCE Fig. 6 DO NOT use a wrench to tighten because it could damage the quick coupling nut and result in a hazardous condition. 7. Open the tank valve fully (counterclockwise). Use a soapy water solution to check all connections for leaks before attempting to light your grill. See “Pre-Operation Leak Testing" on page 19. If a leak is found, turn the Tank Valve off and do not use your grill until the leak is repaired. As shown in Fig. 7a, gas tank must be place vertically.
CARE AND MAINTENANCE Hand Wheel External Thread Thermally Sensitive Nut Propane Regulator Type I Valve PIG 7 Disconnecting a Liquid Propane Gas (LP Gas) Tank from Your Grill: 1. Turn the burner knobs and LP gas tank valve to the full OFF position. (Turn clockwise to close.) 2. Detach the hose and regulator assembly from the LP gas tank valve by turning the quick coupling nut counterclockwise. CAUTION: When the appliance is not in use, the gas must be turned off at the supply tank. L.P.
CARE AND MAINTENANCE Cylinders must not be stored in a building, garage, or any other enclosed area. (The L.P. cylinder must have an overfill protection device and a collar to protect the cylinder valve.) The L.P. gas supply cylinder must be constructed and marked in accordance with the specifications for L.P. gas cylinders of the U.S. Department of Transportation (DOT) or the National Standard of Canada, CAN/CAS-B339, “Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods and Commission.
CARE AND MAINTENANCE 5. Turn off the burner control knobs. 6. Turn the top knob of the fuel supply cylinder counterclockwise two (2) rotations to open. 7. Apply the soap solution to connections of the fuel supply assembly. If no soap bubbles appear, there is no gas leak. If bubbles form at the connections, a leak is detected. If a leak is detected, immediately turn off the gas supply, tighten any leaking fittings, turn gas on, and repeat steps 1-3. 8. Turn off the knob on the fuel supply cylinder. 9.
CARE AND MAINTENANCE Clearance to combustible construction: A minimum of 61 cm (24 inches) from the sides and back must be maintained from the gas grill above and below the cooking surface to adjacent vertical combustible construction. Clearance to non-combustible construction: A minimum of 61 cm (24 inches) clearance from the back of the grill to non-combustible construction is required for the lid to fully open.
CARE AND MAINTENANCE WARNING Heat and smoke exhaust out of the chimney and the ventilation holes on the bottom of two oven side panels (See Fig. 8). Make sure to keep anything that could be damaged by heat or smoke away from the heat and smoke exhaust holes. GENERAL RULES Do not leave the grill unattended while cooking! 1. Make sure the grill has been leak-tested and is properly located. 2. Light the grill burners using the instructions provided in this manual. 3.
CARE AND MAINTENANCE GRILL BURNER LIGHTING Warning: Do not lean over grill when lighting. Turn off LP supply at cylinder when appliance is not in use. Main Burner Lighting Illustration: 1. Check that the control knobs are in the OFF position. 2. Open valve at tank fully by turning counterclockwise. 3. The door must always be in the OPEN position for lighting; 4. Push the Electronic Ignition down 3 to 4 seconds while turning the control knob to the HIGH position. The burner should ignite.
CARE AND MAINTENANCE USING THE GRILL LIGHT Light Operation Instruction 1. Make sure the light’s power switch on the control panel is in the “OFF” position. 2. Connect power plug to properly grounded outlet. 3. Turn the light’s power switch to “ON.” WARNING Keep any electrical supply cord away from any heated surface. Do not turn on the lights when the hood is closed.
CARE AND MAINTENANCE Normal:Soft blue flames Out of Acjustment: Hard blue flames-too much air Poor Combustion: wavy, yellow flames-too little air GENERAL CLEANING IMPORTANT: Before cleaning, make sure all controls are off and the grill is cool. Always follow label instructions on cleaning products. For routine cleaning, wash with soap and water using a soft cloth or sponge. Rinse with clean water and dry at once with a soft, lint-free cloth to avoid spots and streaks.
CARE AND MAINTENANCE NOTE: Allow the drip tray to cool before attempting to clean. Important: Do not leave the grill outside during inclement weather unless it is covered. Rain water can collect inside of the grill, the grill cart or the drip tray if left uncovered. If the drip tray is not cleaned after use and the grill is left uncovered, the drip tray will fill with water causing grease and water to spill into the grill cart. We recommend cleaning a nd storing the drip tray after every use.
CARE AND MAINTENANCE NOTE: Always scrub in the direction of the grain. GRILL LIGHT Bulb Replacement IMPORTANT SAFETY INSTRUCTIONS Lighted lamp is HOT: WARNING -TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION, OR INJURY TO PERSONS. 1. Turn off/unplug and allow to cool before replacing bulb (lamp). 2. Bulb (lamp) gets HOT quickly! Only contact switch/plug when turning on. 3. Do not touch hot lens, guard, or enclosure. 4. Do not remain in light if skin feels warm. 5.
CARE AND MAINTENANCE 28. Turn off/unplug and allow to cool before replacing bulb (lamp). Next, open the door and remove the two cooking grills, smoker box, pizza stone, base grill and flame tamer. 29. Use screw driver to loosen M5*35 screw * 4 pcs that fix the heat shield. And then remove the heat shield. 30. Use screw driver to loosen the screw that fix the light assy.
CARE AND MAINTENANCE 31. Use one hand to hold the metel back part of the light and one handl to hold the front glass cover and then take them apart. Then you can relace the bulb. 32. After replacement, use one hand to hold the metel back part of the light and one handl to hold the front glass cover and then clip them together in the right position.
CARE AND MAINTENANCE 33. Use M4*10 screw to fix the light assy. on to the back panel of the oven. 34. Use screw M5*35×4 pcs to fix the back heat s hield onto the back panel of the oven. smoker box, pizza stone, base grill and flame tamer into the oven.
CARE AND MAINTENANCE Cleaning Method Follow Steps above for glass cover removal. Use a damp towel to clean the surface of glass cover. Make sure the glass cover is completely dry before reinstalling. WARNING Make sure the light switch is on “OFF” position and power plug is disconnected from power outlet prior to cleaning the glass cover. WARNING The light glass cover should not be in contact with water or any other liquid when it is warm. Sudden changes of temperature may cause cracks on glass cover.
CARE AND MAINTENANCE 5. Do not use an outdoor cooking gas appliance for purposes other than intended. 6. When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the outlet. 7. Use only a Ground Fault Interrupter (GFI) protected circuit with this outdoor cooking gas appliance. 8. Never remove the grounding plug or use with a two-prong adaptor. 9.
CARE AND MAINTENANCE 38. Use spanner 19# to loosen the nut that fix the temp. gauge. And then you can completely separate the oven door exterior and interior so as to do the cleaning. 39. After cleaning, you need to re-assemble the oven door. Put the door interior onto the exterior and make every screw hole in line with each other. Use M4*10 screw * 7 pcs to fix the door interior and exterior. And then use shoulder screw to fix the handle onto the door.
CARE AND MAINTENANCE 41. Use M4*10 screw * 4 pcs to fix the door onto the oven. Now you have finished cleaning the oven door.
TROUBLESHOOTING PROBLEM Grill will not light. Burner flame is yellow and gas odour can be smelled. Excessive flare-up. POSSIBLE CAUSE 1. The ignition wire came off the electrical igniter/valve. 2. The distance between the ignition pin and the burner is greater than 3~5 mm. 3. The ignition wire is broken. 4. The battery has died. 5. The battery is in the wrong polarity. 6. The electrode tip does not produce sparks at the burner port. 7. No gas supplied. 8. Air shutter opening is too big. 1.
TROUBLESHOOTING Low heat, LP gas. The propane regulator assembly incorporates an excess flow device designed to supply the grill with sufficient gas flow. Rapid changes in pressure can trigger the excess flow device, providing a low flame and low temperature. Cooking light will not turn on. 1. No power supply. 2. Defective Halogen bulb. 3. Internal wiring issue. 3. Refill the LP tank. Please follow these instructions: 1. Make sure all burners are “OFF .” 2. Open the tank valve and wait 5 minutes. 3.
WARRANTY The appliance has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for five (5) year from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer. Defects or damage caused by the use of other than genuine parts are not covered by this warranty.
EXPLODED DIAGRAM 5 4 3 2 6 7 1 8 9 14 10 11 12 15 13 17 18 16 19 35 46 34 33 36 37 45 32 38 27 28 29 30 31 39 22 21 20 40 26 41 25 24 43 42 44 47 49 51 52 50 48 58 53 54 57 55 56 59 60 61 63 62 74 64 68 73 72 69 70 71 38 65 66 23 67
EXPLODED DIAGRAM No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Part Name Heat spacer Back heat-shield Light assy. Light bracket Handle latch Gas pipe Chimney assy. Cooking grill Smoker box assy. Pizza stone Bottom grill Interior assy. Round burner assy. Exterior Fascia heat shield Oven front panel Back panel Grease tray Electronic igniter Nozzle stator Valve Viewing window Door handle assy. Door heat shield assy.
REPLACEMENT PARTS LIST 1. BG070 -01 Oven Exterior * 1 pc 2. BG070-02-00B Interior * 1 pc 5. BG070-03A Oven Back Heat Shield * 1 pc 9. BG070-32A Stone * 1 pc Oven 3. BG070-24 Burner Bracket Beam * 1 pc 4. BG070B-03-01 Oven Back Panel * 1 pc 6. BG070-10-00B Burner Assy. * 1 pc 7. BG070-18 Grate * 2 pcs 8. BG070-17B Grate * 1 pc Pizza 10. BG070-13-00 Smoker Box * 1 pc 11. BG070-08-00C Chimney Assy. * 1 pc 12. BG070B-05A Control Fascia * 1 pc 13. BG070B-03-02 Light Bezel * 1 pc 14.
REPLACEMENT PARTS LIST 25. BG070B-38 Oven Door Glass * 2 pc 26. BG070-30 Gauge * 1 pc Temp. 27. BG070-12-00 Oven Door Handle Assy. * 1 pc 28. BG070-76-00 Sideshelf * 2 pcs 29. BG070B-30-01 Left Sideshelf Bracket * 2 pcs 30. BG070B-30-02 Right Sideshelf Bracket * 2 pcs 31. BG070B-57-00 Oven Left Holder Panel * 1 pc 32. BG070B-58-00 Oven Right Holder Panel * 1 pc 33. BG070B-59 Oven Back Seal Panel Oven Left Holder Panel * 1 pc 34.
REPLACEMENT PARTS LIST 49. BG070B-53 Trolley Top Panel * 1 pc 50. BG070B-54 Trolley Door Horizontal Beam * 1 pc 51. BG070B-50-00 Trolley Left Sidepanel Assy. * 1 pc 52. BG070B-51-00 Trolley Right Sidepanel Assy. * 1 pc 53. BG070B-52 Trolley Back Panel Assy. * 1 pc 54. BG070B-55 Trolly Door Exterior * 1 pc 55. BG070B-56 Trolly Door Interior * 1 pc 56. BG070-40 Triangle Bracket * 2 pcs 57. DGP350SNP-30-00 Cylinder Tray Assy. * 1 pc 58. BG070-78-00 Trolley Base Panel Assy. * 1 pc 59.