TDS

ManualsBrandsLatex-ite ManualsKitchen4.75-Gal. Ultra Shield Driveway Filler Sealer

Dalton

Enterprises,

Inc.,

131

Willow

Street,

Cheshire,

06410

Phone

800-851-5606

•

Fax

(203)

271-3396

•

www.latexite.com

Revised 07/19

TECHNICAL DATA SHEET

Latex•ite

ULTRA SHIELD

DRIVEWAY SEALER

Manufacturer Product#: 70691

UPC#: 090932706910

Appearance:

Thick brown liquid. Dries black.

Maximum VOC:

Less than 25 g/L

Application Temperature:

40º F and rising.

Specific Gravity:

1.2-1.5

Viscosity:

1,000-5,000 cps

Weight Per Gallon:

10.8-11.6 lbs. per gallon

Color:

Brown in liquid state. Dries black.

Consistency:

Thick liquid.

Boiling Point:

>212º F

Cure Time (50% relative humidity, 70º F):

24-48 hours.

Freeze ability:

Do not allow to freeze.

Container Size & Weight:

4.75gallons, Approximately 55 lbs.

Latex·ite

Ultra Shield

Driveway Filler Sealer is one of our top of the line high performance asphalt driveway sealers.

Ultra Shield

is formulated using an advanced technology that incorporates a flexible polymer system so not only will the

sealer adhere to your driveway better it will adhere to itself better…extending the life of your asphalt investment!

Features:



10 Year Warranty



Ultra Flex Polymers for max flexibility



UV Protection – stays black and won’t fade/dull



Advanced EZ-GEL™ Formula … save time & effort



ThermaSEAL™ Technology – Cures in temperatures down to 40 degrees F



Non-Skid Formula



Low VOC formula, easy soap and water clean up



Apply with Seal Right Squeegee (Roller is wrong applicator and voids warranty)

*Note: Product dries black…is brown only in liquid form.

Coverage rates vary depending upon the condition of the existing blacktop. Smooth & previously sealed driveways will

average 400-500 square feet per pail. Rough & unsealed surfaces will average 300-400 sq. ft. per one 4.75-gallon pail. Rough

/ road-grade asphalts with larger aggregate can cause lower than normal coverage rates. Thin coats are recommended as thick

coats will result in uneven coverage, tracking, and curing problems. A second coat can be applied 24 hours after first

application.

PHYSICAL PROPERTIES & PERFORMANCE

FEATURES

COVERAGE

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA SHEET Latex•ite® ULTRA SHIELDTM DRIVEWAY SEALER Manufacturer Product#: 70691 UPC#: 090932706910 PHYSICAL PROPERTIES & PERFORMANCE Appearance: Thick brown liquid. Dries black. Application Temperature: 40º F and rising. Viscosity: 1,000-5,000 cps Color: Brown in liquid state. Dries black. Boiling Point: >212º F Freeze ability: Do not allow to freeze. Maximum VOC: Less than 25 g/L Specific Gravity: 1.2-1.5 Weight Per Gallon: 10.8-11.6 lbs. per gallon Consistency: Thick liquid.
PAGE 2
SURFACE PREPARATION Sweep and clean off entire driveway using Latex•ite® CLEANER/DEGREASER. Scrub oil, gas spots, stains and rinse with water. Apply Latex•ite® OIL SPOT PRIMER to any oil spots/stains using a paint brush. Allow Latex-ite® OIL SPOT PRIMER to dry ½ hour prior to sealing over. If pavement is extremely hot, apply a fine water mist prior to sealing, but avoid creating any standing water. Brush out any remaining puddles.
PAGE 3
this product, ensure that the container is secured and the lid is secure. Do not allow the container to tumble as this may loosen the lid and allow leakage to occur. Do not transport on passenger seats or inside the passenger compartment of any vehicle. Protective clothing and eyewear should be used during application. CLEAN UP & STORAGE While wet, clean up with soap and water. If dry, scrub with citrus based cleaner. Containers are recyclable. Do not heat or store container in temperatures above 110º F.