Instructions / Assembly

ManualsBrandsLatex-ite ManualsBuilding materials4.75 Gal. Therma Seal Driveway Filler Sealer

LATEX·ITE

THERMA SEAL™

HOW-TO REPAIR AND SEAL YOUR

BLACKTOP DRIVEWAY

For Best Results

REPAIR

Follow application instructions on product container. Plan on prep and repair on one day

and sealing on the next day.

Trim all grass and vegetation away from the edges of the asphalt surface. Leave nothing

overhanging or in contact with the asphalt surface.

Cut out broken or severely cracked areas or deteriorated asphalt using a hammer and cold

chisel. If it is deteriorated along driveway edge, install a piece of wood along the edge of the

driveway to act as a frame.

Sweep and clean off the entire driveway. Remove dirt and pickup loose stones and asphalt

from any ruts, potholes or low spots.

Clean stains using a full strength penetrating cleaner. Apply liberally vigorously scrub with a

stiff wire brush. Rinse away the dirty residue area with water. Repeat this process until clean.

Rinse. If stain is soft, cut out with chisel and follow repair instructions. For gas and oil spots

see below.

Prime any gas and oil spots with an oil spot primer to avoid bleed through.

Fill any cracks up to ½” wide using a crack filler. Allow to cure prior to sealing over.

Trowel Fill large cracks (over ½” wide), areas of allegation, ruts and minor depressions using a

smooth patch. Trowel in layers of 1/4" to 1/2" ...no greater as it sets up from the top down

(maximum is two layers / ‘lifts’). Allow each layer to harden overnight before applying next

layer. Level and feather out the edges for a smooth, neat, uniform appearance. Allow 24 hours

to cure prior to sealing over.

Summary of content (4 pages)

PAGE 1
LATEX·ITE® THERMA SEAL™ HOW-TO REPAIR AND SEAL YOUR BLACKTOP DRIVEWAY For Best Results REPAIR Follow application instructions on product container. Plan on prep and repair on one day and sealing on the next day. Trim all grass and vegetation away from the edges of the asphalt surface. Leave nothing overhanging or in contact with the asphalt surface. Cut out broken or severely cracked areas or deteriorated asphalt using a hammer and cold chisel.
PAGE 2
Fill potholes using a stone patch. Make sure you have clearly identified sidewalls (you can use a chisel to create a border) and tamp in thoroughly. Allow 2 weeks prior to sealing over. If water beads up on repair that means it is not ready for sealer. SEAL Before you begin make sure all repairs have properly cured. Pick a nice day that is warmer than 40 F (at night) and no rain in the forecast for 36 hours. Make sure you have enough sealer as you don’t want to run short. Buy an extra pail just in case.
PAGE 3
REPARAR Siga las instrucciones de aplicación en el envase del producto. Plan en la preparación y la reparación en un día y de sellado en el día siguiente. Recorte toda la hierba y la vegetación de los bordes de la superficie de asfalto. No dejar nada en voladizo o en contacto con la superficie de asfalto. Cortar las zonas rotas o agrietadas o gravemente deteriorado asfalto utilizando un martillo y un cincel.
PAGE 4
su entrada es limpio y seco que esté listo para ir. En un día caluroso puede humedecer ligeramente el camino de entrada y aplique cuando está húmedo. El uso de un inicio escobilla de goma en el extremo superior de la calzada Normalmente revuelven los cubos no necesitará utilizar una mezcla rápida, pero para estar seguro de que es buena idea para darle la vuelta al cubo de al menos 24 horas antes de usar el producto. (Inspeccione cuidadosamente la tapa para asegurarse de que es seguro antes de entregar).