Datasheet

ManualsBrandsLAPPKABEL ManualsIndustrial Data CablesControl wiring ÖLFLEX® CLASSIC 110 SY 7 G 1 mm² Grey, Transparent 50 m

U.I. Lapp

GmbH

DAT

A SHEET

ÖLFLEX

CLASSIC 110 SY

DB 1125752

valid from: 2013-03-08

Originator: KASC / PDC

approved: HAPF / PDC

Document: DB1125752EN Page 1 of 1

PD 0019/2.2_11.10EN

Application

ÖLFLEX



CLASSIC 110 SY cables are VDE approved power and control cables for occasional flexible use and fixed installa-

tion under normal mechanical load conditions. They are for use in dry, damp and wet rooms. They may only be installed

outdoors with UV-protection and in observation of the temperature range. At room temperature it is widely resistant against

acids, caustics solutions and certain oils. ÖLFLEX



CLASSIC 110 SY suitable for freely moved without forced guidance and

tensile stress. The braid of galvanized steel-wires is an additional mechanical protection.

Application range:

ÖLFLEX



CLASSIC 110 SY cables are used in plant engineering, in industrial machinery and in heating and air conditioning

systems as well as in areas with high mechanical stress.

Design

Design based on

EN 50525-2-51resp. VDE 0285-525-2-51 / HD 21.13 S1 + A1 resp. VDE 0281-13

Approval VDE-Reg.-Nr. 7030

Conductor fine wire strands of bare copper, acc. to IEC 60228 resp. VDE 0295, class 5

Core insulation PVC compound TI2 acc. to EN 50363-3 resp. VDE 0207-363-3 with increased

requirements acc. to Lapp specification

Core identification acc. to VDE 0293-1, with or without GN/YE ground conductor

black cores with white numbers acc. to DIN EN 50334 resp. VDE 0293-334

Inner sheath PVC compound TM2 acc. to EN 50363-4-1 resp. VDE 0207-363-4-1

colour: silver grey, similar RAL 7001

Braid braid of galvanized steel-wires, coverage = 70 % (nominal value)

Outer sheath PVC compound TM2 acc. to EN 50363-4-1 resp. VDE 0207-363-4-1

colour: transparent

Electrical properties

Nominal voltage U

/ U: 300 / 500 V

Test voltage Core/Core: 4000 V AC

Core/Screen: 4000 V AC

Mechanical and thermal properties

Min. bending radius occasional flexing: 20 x outer diameter

fixed installation: 6 x outer diameter

Temperature range occasional flexing: -5 °C up to +70 °C max. conductor temp.

fixed installation: -40 °C up to +80 °C max. conductor temp.

Flammability acc. to IEC 60332-1-2 resp. VDE 0482-332-1-2

Tests acc. to IEC 60811, EN 50395, EN 50396

EC-Directives This cable is conform to the EC-Directives 2006/95/EC (Low Voltage Directive)

and 2011/65/EU (RoHS, Restriction of the use of certain hazardous substances).

Summary of content (1 pages)

PAGE 1
U.I. Lapp GmbH DATA SHEET ÖLFLEX® CLASSIC 110 SY DB 1125752 valid from: 2013-03-08 Application ÖLFLEX CLASSIC 110 SY cables are VDE approved power and control cables for occasional flexible use and fixed installation under normal mechanical load conditions. They are for use in dry, damp and wet rooms. They may only be installed outdoors with UV-protection and in observation of the temperature range. At room temperature it is widely resistant against acids, caustics solutions and certain oils.