Use and Care Manual

ManualsBrandsLa-Z Boy ManualsDecorBellamy Coffee Brown Bonded Leather Executive Office Chair

Chair Assembly Instructions

Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components,

assemble the chair on a protected surface.

Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood ﬂoors. Using

these casters on tile or wood ﬂooring may cause ﬂoor surface damage, so please consider purchasing a chairmat to protect your ﬂoor

surfaces.

We are here to help if you have any questions, comments, or are in need of warranty replacement parts.

Visit our website at : www.truecustomersupport.com

Or call us toll free at : 1-855-372-2315

(Monday - Friday 6:00 am – 5:00 pm Paciﬁc Time)

Instrucciones de ensamblaje

Desembale todas las partes con cuidado e identifíquelas usando la lista de partes antes de empezar el

ensamblaje. Ponga la sillón sobre una superﬁcie protegida para evitar rayar los componentes al ensamblarlo.

Nota: Las ruedas que vienen con este sillón han sido diseñadas para pisos alfombrados. No es recomendable su uso en pisos de

cerámica o madera. Estas ruedas pueden causar daños en la superﬁcie de los pisos de cerámica o madera, por lo que le sugerimos que

coloque un tapete debajo del sillón para proteger el piso.

Estamos aquí para ayudarle con cualquier pregunta, comentario, o necesidad de partes de

repuesto de garantía.

Visítanos en : www.truecustomersupport.com

Por favor llámenos a nuestro número gratuito : 1-855-372-2315

(Lunes-Viernes 6:00 am - 5:00 pm Horario Oﬁcial del Pacíﬁco).

Summary of content (15 pages)

PAGE 1
Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood floors. Using these casters on tile or wood flooring may cause floor surface damage, so please consider purchasing a chairmat to protect your floor surfaces.
PAGE 2
PARTS/PARTES A Casters Ruedas Quantity/cantidad: 5 B Star Base Base en forma de estrella Quantity/cantidad:1 D1 C Gas Lift with Telescoping Cover Elevador neumático y cubierta telescópica D Seat Plate Mecanismo del asiento D2 Quantity/cantidad: 1 Quantity/cantidad: 1 E1 Right Arm Brazo derecho Quantity/cantidad: 1 H Plastic Shroud Cubierta de plástico Quantity/cantidad: 1 E2 Left Arm Brazo izquierdo Quantity/cantidad: 1 I 1” Screws Tornillos de 25mm Quantity/cantidad: 2 M L 2-1/2” Screws T
PAGE 3
Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). A Paso 1 Ponga la base en forma de estrella (B) con las patas hacia arriba y inserte las 5 ruedas (A) en los hoyos situados en la base (B). B C Step 2 Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover (C) through the center hole on top of Star Base (B).
PAGE 4
Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-3/4” Screws (J) for the front holes of the Seat Plate (D) and 1” Screws (I) for the rear holes of the Seat Plate (D) and tighten screws. *Note : Tighten the screws completely.
PAGE 5
Step 4 Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever receivers on the underside of Seat Cushion (F) (with the front of the levers facing the front of seat cushion). Push down the key on the receivers to pull out the levers. *Note : Fix the cable for the seat plate into the plastic clips attached to the bottom of the seat cushion.
PAGE 6
Step 5 Attach the Back Cushion (G) to the Seat Cushion (F) by positioning the back support plate over the Seat Plate (D) with1-1/4” Screws (K). *Note : Do not tighten the screws completely. F Paso 5 Alinee el cojín del respaldo (G) con el cojín del asiento (F) por medio de colocar la placa de soporte del respaldo sobre la placa del asiento (D) con tornillos de 32mm (K). *Nota : No ajuste los tornillos completamente.
PAGE 7
Step 6 Insert 2-1/2” Screws (L) into arm holes, attaching Arms (E1 & E2) (with the front of arms facing the front of seat cushion) to sides of Seat Cushion (F) and Back Cushion (G). *Note : Tighten all the screws completely. Remember to tighten the back support plate screws.
PAGE 8
Step 7 Put the Plastic Shroud (H) over the Seat Plate (D) (with the front of plastic shroud facing the front of seat cushion). Align shroud posts to holes on bottom of Seat Cushion (F) and press into position. F H Paso 7 Coloque la cubierta de plástico (H) sobre la plancha del asiento (D) (con la parte frontal de la cubierta de plástico mirando hacia el frente del cojín del asiento).
PAGE 9
Step 8 Position the assembled chair upright with the seat plate facing down. Insert the Gas Lift with Telescoping Cover (C) into the center hole of the Seat Plate (D). Paso 8 Coloque la silla ensamblada verticalmente, con la plancha del asiento hacia abajo. Inserte el elevador neumático con la cubierta telescópica (C) en el hoyo central de la mecanismo del asiento (D). Step 9 Press the Plastic Caps (M) into armrest holes once all screws have been tightened.
PAGE 10
Operating Instructions Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height : While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release lever to lock chair at desired height. To lower the seat, lift the lever while seated. The chair will descend until the lever is released or the chair reaches the bottom position.
PAGE 11
Function Instruction - 2 To Operate Tilt Lockout : While seated, reach under the left side of the chair to find the lever. Push down the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the up position. Instrucciones de Funcionamiento - 2 Para operar el seguro de la inclinación : Cuando esté sentado, busque la palanca debajo del costado izquierdo de la silla.
PAGE 12
Function Instruction - 3 To Adjust Tension On The Tilt : Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user. Rotate the knob (R) until the desired resistance is reached.
PAGE 13
Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned seating products.
PAGE 14
Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así demostrado por el recibo original. Esta garantía no le aplica a muebles usados comprados “como tales”.
PAGE 15
LA-Z-BOY is a trademark of La-Z-Boy Incorporated and is used under license to LF Products Pte Ltd. LA-Z-BOY es una marca de La-Z-Boy Incorporated y es usada con licencia de LF Products Pte Ltd.