KM-1500 Please read the Operation Guide before using the copier Keep it close to the copier for easy reference
All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Legal Restriction On Copying • It may be prohibited to copy copyrighted material without permission of the copyright owner. • It is prohibited under any circumstances to copy domestic or foreign currencies.
Introduction to this Operation Guide The explanations contained in this operation guide have been separated into different sections in order to allow even those using a copier for the first time to use this machine efficiently, properly and with relative ease. A basic introduction to each section can be found below for reference. Refer to the related section when using this copier.
CONTENTS Energy Star Program ...................................................................... iii Please read this Operation Guide before using the copier. Keep it close to the copier for easy reference. ..............................................iv Section 1 IMPORTANT! PLEASE READ FIRST. 1-1 CAUTION LABELS .......................................................................1-1 INSTALLATION PRECAUTIONS ................................................1-2 PRECAUTIONS FOR USE .....................
Energy Star Program We have determined as a participating company in the International Energy Star Program that this product is compliant with the standards laid out in the International Energy Star Program.
Please read this Operation Guide before using the copier. Keep it close to the copier for easy reference. Please read this Operation Guide before using the copier. Keep it close to the copier for easy reference. The sections of this guide and parts of the copier marked with symbols are safety warnings meant to protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the copier. The symbols and their meanings are indicated below.
Section 1 IMPORTANT! PLEASE READ FIRST. CAUTION LABELS Caution labels have been attached to the copier at the following locations for safety purposes. BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when removing a paper jam or when replacing toner. Label 1 High temperature inside. Do not touch parts in this area, because there is a danger of getting burned. .............................................. Label 2 High temperature inside.
INSTALLATION PRECAUTIONS Environment CAUTION Avoid placing the copier on or in locations which are unstable or not level. Such locations may cause the copier to fall down or fall over. This type of situation presents a danger of personal injury or damage to the copier. ............................................................................. Avoid locations with humidity or dust and dirt. If dust or dirt become attached to the power plug, clean the plug to avoid the danger of fire or electrical shock.
PRECAUTIONS FOR USE Cautions when using the copier WARNING DO NOT place metallic objects or containers with water (flower vases, flower pots, cups, etc.) on or near the copier. This of situation presents a danger of fire or electrical shock should they fall inside. .................................. DO NOT remove any of the covers from the copier as there is a danger of electrical shock from high voltage parts inside the copier. .... DO NOT damage, break or attempt to repair the power cord.
Other precautions DO NOT place heavy objects on the copier or cause other damage to the copier. DO NOT open the upper front cover, turn off the power switch, or pull out the power plug during copying. When lifting or moving the copier, contact your service representative. Do not touch electrical parts, such as connectors or printed circuit boards. They could be damaged by static electricity. DO NOT attempt to perform any operations not explained in this handbook.
Laser Safety Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this machine is hermetically sealed within the protective housing and external cover. In the normal operation of the product by user, no radiation can leak from the machine. This machine is classified as Class 1 laser product under IEC 60825. CAUTION Performance of procedures other than those specified in this manual may result in hazardous radiation exposure.
CAUTION! The power plug is the main isolation device! Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source. VORSICHT! Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem Gerät sind nur Funktionsschalter und können nicht verwendet werden, um den Stromfluß im Gerät zu unterbrechen.
DECLARATION OF CONFORMITY TO 89/336/EEC, 73/23/EEC and 93/68/EEC We declare under our sole responsibility that the product to which this declaration relates is in conformity with the following specifications.
1-8
Section 2 NAMES OF PARTS Main Body (1) (7) (11) (3) (4) (2) (5) (6) (9) (8) (10) (1) Original cover (Open/close this cover when you are setting the original on the platen.) (2) Platen (Set originals here for copying. Be sure to lay originals face-down and align them flush up against the left rear corner of the platen.) (3) Original size indicator plate (Be sure to align originals flush up against this plate when setting them on the platen.) (4) Operation panel (Perform copy operations here.
Section 2 NAMES OF PARTS (16) (15) (14) (13) (13) (19) (19) (12) (17) (12) Drawer (This drawer has a storage capacity of 250 sheets of standard copy paper (80 g/m²).) (13) Paper width guides (Adjust these guides to fit the width of the paper that is to be loaded in the drawer.) (14) Paper stopper (Adjust this stopper to fit the length of the paper that is to be loaded in the drawer.) (15) Stopper extension lock (Use this lock when loading Folio or Oficio II size paper in the drawer.
Section 2 NAMES OF PARTS (23) (24) (21) (20) (22) (20) Power switch (Turn this switch ON ( | ) before copying.) (21) Face-up tray (Finished copies can be ejected and stored face-up on this tray. The face-up tray should be used when copying onto thick paper and other special paper. This tray has a storage capacity of 30 sheets of standard copy paper (80 g/m²) but only 1 sheet of special paper should be stored there at one time.
Section 2 NAMES OF PARTS Operation panel (24) (23) (19) (21) (22) (18) (20) (12) (6) (17) (5) (11) (8) (9) (1) Start key & indicator (Press this key when you want to start copying. Copying will begin immediately if you press this key when the indicator is lit green.) (2) Reset/Power key (Press this key when you want to cancel the currently entered setting(s) and return to those registered for the initial mode. Press down on this key for at least 3 seconds when you want to engage the Off mode.
Section 2 NAMES OF PARTS (15) Program key & indicator (Press this key when you want to copy with the Program function. Make sure that the Program indicator is lit green.) (16) Add Toner indicator (This indicator lights red when the toner supply has run low. See page 8-2.) (17) Memory Overflow indicator (This indicator lights red if the memory becomes full during scanning of originals. See page 7-1.
Section 2 NAMES OF PARTS 2-6
Section 3 PREPARATIONS Loading paper Copy paper can either be loaded into the drawer(s) or set on the multi-bypass tray. Note when adding paper After taking new paper out of its packaging, be sure to fan through them a few times to separate the sheets before loading the paper into a drawer or setting it on the multi-bypass tray. Loading paper into a drawer Standard copy paper (60 g/m² – 90 g/m²), thick paper (90 g/m² – 105 g/m²), recycled paper, or color paper can be loaded into each drawer.
Section 3 PREPARATIONS 1 Pull the drawer all the way out of the copier. 4 Set the paper in the drawer so that the leading edge is aligned against the paper stopper, but making sure that none of the paper gets caught on the overhanging tabs. IMPORTANT! When pulling the drawer out of the copier, be sure to support it so that it doesn’t fall out suddenly.
Section 3 PREPARATIONS 5 Push the drawer securely all the way back into the copier until it stops. Adjusting the paper stopper for Folio or Oficio II size paper Perform the following procedure to adjust the paper stopper when you want to load Folio or Oficio II size paper into the drawer. 1 Remove the stopper extension lock from the paper stopper.
Section 3 PREPARATIONS 4 Press down on the stopper extension lock and slide the paper stopper towards the rear of the drawer to set the lock into place. The paper stopper is now in position for Folio and Oficio II size paper. Selecting the paper size Perform the following procedure to use the operation panel and select the size of paper that is loaded in the drawer. 1 2 Press down on the Paper Select key for at least 3 seconds. The first default item for paper size selection will be shown.
Section 3 PREPARATIONS 4 Press the Number of Copies / Zoom(+) or Number of Copies / Zoom(-) key to select the appropriate paper size. The displayed code numbers refer to the available paper sizes as explained in the following table. Setting paper on the multi-bypass tray Standard copy paper (60 g/m² – 90 g/m²), thick paper (90 g/m² – 163 g/m²), color paper, OHP transparencies and letterhead paper can be set on the multi-bypass tray. ALWAYS use the multi-bypass tray when copying onto special paper.
Section 3 PREPARATIONS 1 2 Open the multi-bypass tray towards you until you hear it click into place. Pull out the multi-bypass extension and then flip it open. 4 Slide the paper all the way in, along the insert guides, as far as it will go. IMPORTANT! • Only set paper on the multi-bypass tray when you are planning to use that tray to feed paper. DO NOT leave paper on the multi-bypass for long periods of time.
Section 3 PREPARATIONS Selecting the paper size 4 Perform the following procedure to use the operation panel and select the size of paper that is set on the multi-bypass tray. There are two methods of selecting the paper size for the multi-bypass tray: standard and temporary. The standard setting will remain in memory even when the power switch copier is turned OFF, while the temporary setting will be cleared each time the power switch is turned OFF.
Section 3 PREPARATIONS Selecting the paper size (temporary setting) 1 2 Press the Paper Select key until the multi-bypass tray indicator is lit. Press the Number of Copies / Zoom(+) or Number of Copies / Zoom(-) key to select the appropriate paper size. The displayed code numbers refer to the available paper sizes as explained in the following table.
Section 3 PREPARATIONS Thick Paper mode Perform the following procedure to select the Thick Paper mode when copying onto thick copy paper (90 g/m² – 163 g/m²). When this mode is selected, copying will be carried out at a higher fixing temperature and the copy speed will be lowered in order to ensure efficient fixing of the toner to the copy paper. 1 2 Press the Thick Paper key. The Thick Paper indicator will light. Perform the standard copying procedure.
Section 3 PREPARATIONS Attaching the face-up tray When copying onto special paper, such as thick paper (90 g/m² – 163 g/m²) and OHP transparencies, ALWAYS use the face-up tray. The face-up tray has a storage capacity of 30 sheets of standard copy paper (80 g/m²) but only 1 sheet of special paper should be stored there at one time. 2 Perform the standard copying procedure. Finished copies will be ejected onto the face-up tray. NOTES 1 Open the face-up tray (located at the rear of the copier).
Section 4 BASIC OPERATION Basic copying procedure 1 2 3 Warm-up Turn the power switch ON ( | ). At the end of warm-up, the Start indicator will light. 4 Selecting the image quality The image quality mode can be selected according to the type of original. Press the image quality select key to light the indicator for one of the following image quality modes. Auto Exposure Adjustment mode: Make sure the Auto Exp. indicator is lit.
Section 4 BASIC OPERATION 5 Adjusting the copy exposure The copy exposure can be manually adjusted in all of the image quality modes, except for the Auto Exposure Adjustment mode. If you want to make the exposure darker, press the right exposure adjustment key to move the lit indicator to the right. If you want to make the exposure lighter, press the left exposure adjustment key to move the lit indicator to the left.
Section 4 BASIC OPERATION 9 At the end of copying Finished copies will be ejected onto the copy storage table. NOTE The copy storage table has a storage capacity of 150 sheets of standard copy paper (80 g/m²). CAUTION If the copier will not be used for a short period of time (overnight, etc.), turn the power switch OFF ({). If it will not be used for an extended period of time (vacations, etc.), remove the power plug from the outlet for safety purposes during the time the copier is not in use.
Section 4 BASIC OPERATION Making enlarged and reduced copies 3 Zoom mode With this mode, the magnification ratio can be set to any 1% increment between 50% and 200%. 50% 200% 1 2 4-4 Press the Recall%/Enter key. The magnification ratio will be shown on copy quantity/magnification display and the “%” symbol will light. Press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key, as appropriate, to change the displayed magnification ratio to the desired ratio.
Section 4 BASIC OPERATION Preset Zoom mode With this mode, the magnification ratio can be set to one of the pre-set ratios: 3 Press the Recall%/Enter key. The new magnification ratio will be registered and the copy quantity/magnification display will return to showing the number of copies to be made.
Section 4 BASIC OPERATION 4-6
Section 5 COPY FUNCTIONS Layout modes With this mode, the images from either 2 or 4 originals can be reduced and then combined onto a single copy. In addition, the borderline of each original can also be marked with a solid or dotted line. 2-in-1 Use this mode when you want to copy two originals onto each sheet of copy paper. Original Copy NOTES • It is possible for you to change the default setting for the borderline. (See “Selecting the borderline” on page 5-6.
Section 5 COPY FUNCTIONS Caution on setting the originals The following illustrations indicate how the orientation of the original will affect the resulting copies. NOTE Make sure the originals are set so that the first page is scanned first.
Section 5 COPY FUNCTIONS NOTE Make sure the originals are set so that the first page is scanned first.
Section 5 COPY FUNCTIONS 1 Press the 2in1/4in1 key until the 2in1 indicator lights. NOTE It is possible for you to change the type of borderline. (See “Selecting the borderline” on page 5-6.) 2 Set the original(s). 3 Press the Start key. Scanning of the first original will start. NOTE If the optional Document Processor is installed on your copier, all of the originals set there will be scanned and the copy operation will start.
Section 5 COPY FUNCTIONS 4-in-1 Use this mode when you want to copy four originals onto each sheet of copy paper. Original Copy Caution on setting the originals Be sure to set the originals as shown in the following illustrations. NOTES • Make sure the originals are set so that the first page is scanned first. • It is possible to select the order in which the images will appear within the copy page.
Section 5 COPY FUNCTIONS 3 Press the Start key. Scanning of the first original will start. Selecting the borderline Perform the following procedure when you want to change the type of borderline. NOTE If the optional Document Processor is installed on your copier, all of the originals set there will be scanned and the copy operation will start. 4 1 Once scanning of the first original is completed, “1-” (the number of originals already scanned) will be shown.
Section 5 COPY FUNCTIONS 4 Press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key to select the desired borderline. The displayed code numbers refer to the available borderline types as explained in the following table. Selecting the order of 4-in-1 layout Perform the following procedure if you want to select the order in which the images will appear within the copy page in the 4-in-1 mode.
Section 5 COPY FUNCTIONS 4 Press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key until the number that corresponds to desired layout order (1 – 4) is shown. The displayed code numbers refer to the available layout orders as explained in the following table. 1-: 1 2 2-: 3 4 3-: 5 5-8 1 3 2 4 1 3 2 4 4-: 1 2 3 4 Press the Recall%/Enter key. The displayed numbers will flash and the copier will return to a copy-ready state.
Section 5 COPY FUNCTIONS Sort mode Multiple originals can be scanned into memory in a single operation and then the desired number of copy sets created. Original 1 4 Once scanning of the first original is completed, “1-” (the number of originals already scanned) will be shown. Set the next original and press the Start key. Carry out this step as well for the rest of the originals that you want to copy. Copy Press the Sort key to light the Sort indicator. 5 2 Set the original(s).
Section 5 COPY FUNCTIONS 5-10
Section 6 COPY DEFAULT SETTINGS Available default items The state that the copier enters at the end of warm-up or when the Reset/Power key is pressed is called the “initial mode”. The modes, functions and other settings that are automatically pre-set for use in the initial mode are called “default settings”. These default settings can be changed as desired to suit your copying needs.
Section 6 COPY DEFAULT SETTINGS Item number 6-2 Reference page Default Description Available settings F14 Multi-Bypass Tray Paper Size Registers the size of paper that is to be set on the multi-bypass tray. * The “XXX” shown here refers to the actual width of the paper as registered under the “Non-Standard Size Paper Width” and it is that number which will be shown on the display.
Section 6 COPY DEFAULT SETTINGS Item number Available settings Reference page Default Description F28 Paper Feeder Skewed Feed Adjustment (option) Adjusts for off-center printing. * If the optional Paper Feeder is not installed on your copier, this default setting will not appear. -1.0 – 3.0 (mm) (Adjustment is complete at the time of purchase.) 6-4 6-6 F29 Multi-Bypass Tray Skewed Feed Adjustment Adjusts for off-center printing. -1.0 – 3.0 (mm) (Adjustment is complete at the time of purchase.
Section 6 COPY DEFAULT SETTINGS Accessing and changing the default settings NOTE 3 If you want to access the “F30” default item (Document Processor Skewed Feed Adjustment), proceed directly to step 18. To access the “F26” default item (Document Processor Leading Edge Timing Adjustment), proceed directly to step 26. 1 2 Press down on both exposure adjustment keys for at least 3 seconds. The “F00” default item number will appear on the copy quantity/magnification display.
Section 6 COPY DEFAULT SETTINGS Sample User Copy Setting List 5 6 Sample Toner Coverage Report 7 Press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key to select either ON or OFF. (F21 and F25) Press the Recall%/Enter key. The operation panel will return to the display in step 2. Once you are finished accessing default items, proceed to step 17. Press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key to set the width of the paper.
Section 6 COPY DEFAULT SETTINGS 8 Press the Recall%/Enter key. The operation panel will return to the display in step 2. Once you are finished accessing default items, proceed to step 17. 11 If the result is as shown in example (1), increase the setting. If the result is as shown in example (2), decrease the setting. (1) (2) 9 Press the Start key. A pattern like that shown in the following illustration will be printed out. (F27, F28 and F29) + – NOTE For each tenth (0.
Section 6 COPY DEFAULT SETTINGS 15 The selected setting will change each time you press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key. Refer to the tables under “Available default items” on page 6-1 to select the number that corresponds to the desired default setting. (F08, F12 – F14, F23 and F24) 18 19 16 Select a standard copy mode and set the original in the Document Processor.
Section 6 COPY DEFAULT SETTINGS 23 If the result is as shown in example (1), increase the setting. If the result is as shown in example (2), decrease the setting. (1) (2) 26 + – 27 Prior to performing the adjustment procedure, it is necessary to use the Document Processor to make copies in a standard copy mode in order to check the amount of shift that is produced.
Section 6 COPY DEFAULT SETTINGS 30 Arrange the original and copy one on top of the other to verify the direction and amount of the shift. If the result is as shown in example (1), increase the setting. If the result is as shown in example (2), decrease the setting. (1) (2) + – NOTE It is possible to change the setting to any number (step) between -32 - 32. Each one-step adjustment is equal to a 0.3 mm shift. 31 32 Press the Recall%/Enter key.
Section 6 COPY DEFAULT SETTINGS Checking the total copy count and printing out a report It is possible to use the operation panel to check the total number of copies made. It is also possible to print out that information in the form of a report. 1 2 Sample Total Count Report Press down on the Stop/Clear key for at least 3 seconds. The copy count will begin to be shown on the copy quantity/ magnification display. The copy count will be shown in three portions in the following order.
Section 7 TROUBLESHOOTING If one of the following indications is displayed When any of the following indications appears on the copy quantity/magnification display, perform the corresponding procedure. Indication Procedure Reference Page “E07” appears on the copy quantity/ magnification display The size of paper registered in the default settings is different than the size of the paper actually used. Check the paper size.
Section 7 TROUBLESHOOTING Indication Procedure Reference Page “E72” appears on the copy quantity/ magnification display Originals for another job were set in the optional Document Processor during copying from the platen in the 2-in-1 or 4-in-1 layout mode or in the Sort mode. Remove the new originals from the Document Processor and, once the copy operation for the 2-in-1 or 4-in-1 layout mode or the Sort mode is completed, reset them on the original table and try to copy again.
Section 7 TROUBLESHOOTING If paper jams If a paper jam occurs, copying will stop. In this case, an indication about the jam will appear on the operation panel. Leave the power switch ON ( | ) and refer to “Removal procedures” on page 7-4 to remove the jammed paper. Misfeed location indicators (1) (2) (3) (4) (1) Lights when an original jams in the Document Processor. (2) Lights when a paper jam has occurred either in the multi-bypass tray or inside the copier.
Section 7 TROUBLESHOOTING Removal procedures 4 Paper jam inside the copier NOTE If the leading edge of the jammed paper is visible, pull it out towards you. If the paper is not visible at all, perform the “Paper jam in a drawer” procedure. If the paper has been fed to the rear of the copier but the leading edge is not visible, perform the “Paper jam in the paper eject section” procedure. If there are any finished copies on the copy storage table, remove them first before performing this procedure.
Section 7 TROUBLESHOOTING Paper jam in a drawer 1 Pull out the drawer that is currently being used. 2 Remove the jammed paper. 4 Open and then close the upper front cover. The error indications will go out. NOTE If a paper jam occurs in the optional Paper Feeder, the procedure to remove jammed paper is the same as with the included drawer. 3 Push the drawer back in firmly.
Section 7 TROUBLESHOOTING Paper jam in the paper eject section 1 Open the face-up tray. 2 Remove the jammed paper. CAUTION The copier’s fixing unit is extremely hot. Take sufficient care when working in this area, as there is a danger of getting burned. 3 7-6 Close the face-up tray. 4 Open and then close the upper front cover. The error indications will go out.
Section 7 TROUBLESHOOTING Paper jam in the multi-bypass tray 1 2 3 Remove all of the paper remaining on the multi-bypass tray. Open and then close the upper front cover. The error indications will go out. Reset the paper on the multi-bypass tray. Original jam in the optional Document Processor 1 Remove all of the originals remaining on the original table. 2 Open the left cover to the Document Processor. 3 4 Remove the jammed original.
Section 7 TROUBLESHOOTING 5 Remove the jammed original. 6 Close the Document Processor. 7 Reset the originals.
Section 7 TROUBLESHOOTING If other trouble occurs If trouble occurs with your copier, carry out the applicable checkpoints and procedures indicated on the following pages. If the trouble persists, contact your service representative or authorized service center. Trouble Checkpoint Procedure Reference Page Nothing lights on the operation panel when the power switch is turned ON. Is the power plug connected to an AC outlet? Connect the plug to an AC outlet.
Section 7 TROUBLESHOOTING Checkpoint Black or white vertical bands appear on the copies. Is the charger cleaner in its home position (marked “CLEANER HOME POSITION”)? Remove the Process Unit and return the charger cleaner to its home position. 8-4 If you are using the optional Document Processor, is the slit glass dirty? Clean the slit glass. It is also possible to use the Black Line Correction function to make black lines on the copies less apparent.
Section 8 MAINTENANCE AND OPERATION INFORMATION Cleaning the copier CAUTION If the optional Document Processor is installed on your copier, lift open the Document Processor and wipe the gray portion, as shown in the illustration, with a soft cloth dampened with alcohol or mild detergent. For safety purposes, ALWAYS remove the power plug from the outlet when performing cleaning operations.
Section 8 MAINTENANCE AND OPERATION INFORMATION Replacing the toner container When toner runs low, the Add Toner indicator will light. If you continue to make copies while the Add Toner indicator is lit, “E33” will appear on the copy quantity/magnification display and the copier will stop. Replace the toner container right away. In addition, you should perform the appropriate cleaning operation whenever you replace the toner container. 1 Open the upper front cover. 2 Open the front cover.
Section 8 MAINTENANCE AND OPERATION INFORMATION 4 5 Pull the lock lever towards you into its release position (marked “UNLOCK”), then pull the toner container release lever to the right as indicated by the arrow (Î) in the illustration. 6 Shake the new toner container horizontally 5 or 6 times to ensure that the toner is evenly distributed inside. 7 Remove the orange protective seal. 8 Set the new toner container into the Process Unit. Gently remove the old toner container.
Section 8 MAINTENANCE AND OPERATION INFORMATION 9 Hold the Process Unit stable and push on the areas marked “PUSH HERE” on the toner container, until the container clicks into place. Cleaning the charger and the registration roller Perform the following cleaning operation whenever you replace the toner container. 11 10 Slide the green-colored charger cleaner knob back and forth 2 to 3 times, then return it to its home position (marked “CLEANER HOME POSITION”).
Section 8 MAINTENANCE AND OPERATION INFORMATION 14 Close the front cover. 15 Close the upper front cover. After use, ALWAYS dispose of the toner container in accordance with Federal, State and Local rules and regulations.
Section 8 MAINTENANCE AND OPERATION INFORMATION Specifications Main Body Type.................................................................................Desktop Original table .................................................................Fixed type Copying system ..............................................................Indirect electrostatic system Acceptable originals .......................................................
Section 8 MAINTENANCE AND OPERATION INFORMATION Document Processor (option) Original feed system ...................................................... Automatic feeding Acceptable originals....................................................... Sheets of paper Original sizes ................................................................. Max.: 8 1/2" × 14" (Legal) and Folio Min.: 5 1/2" × 8 1/2" (Statement) and A5R Original paper weight....................................................
Section 8 MAINTENANCE AND OPERATION INFORMATION Environmental Specifications • Recovery time from the Low Power mode..................10 seconds • Transition time to the Low Power mode (at time of purchase) ...................................................15 minutes • Transition time to the Off and Sleep modes (at time of purchase) ...................................................
For best copy results and machine performance, we recommend that you use only KYOCERA MITA original supplies for your KYOCERA MITA copier.
% & # 0 4 ( : 5 # ! " / ( , ( >>666 - < ) & ( < B ) ) 4 C - < ) & ( < # 0 4 ( : 5 # ! " $ % & E) E ) $ > /# ' & < & 5 ), ) F # % $9 # = .
