Installation Guide

ManualsBrandsKwikset ManualsDeadboltsPowerbolt2 Satin Nickel Single Cylinder Electronic Deadbolt Featuring SmartKey Security and Cove Passage Knob

door frame

Make sure hole in door frame is drilled a

minimum of 1” (25 mm) deep.

Required tools

Ruler4 AA Batteries

Hammer

Wood

block

Pliers

Phillips screwdriver

Additional Tools (depending on application)

If drilling a new door, use the supplied template and the complete

door drilling instructions available at www.kwikset.com/doorprep

Note: Additional door preparation may be

required for doors with 11/2" (38 mm) holes.

Consult the deadbolt drilling instructions at

www.kwikset.com/doorprep

backset

Measure to conirm that the hole in

the door is either 21/8" (54 mm) or

11/2" (38 mm).

Measure to conirm that the backset is

either 23/8" or 23/4" (60 or 70 mm).

23/8" or 23/4"

60 or 70 mm

13/8" or 13/4"

35 mm or 44 mm

Measure to conirm that the hole in

the door edge is 1" (25 mm).

Measure to conirm that the

door is either 13/8" or 13/4"

(35 mm or 44 mm) thick.

A B C

B C D

21/8"

54 mm

11/2"

38 mm

25 mm

Prepare the door and check dimensions

Install the latch and strike

Latch

Exterior Assembly

Interior Cover

Strike SmartKey Tool

J L M

F G H

B C D

Parts List

Drive-In Collar

Keys

Latch and

Strike Screws

Mounting Plate

Interior Assembly

Screws

Interior

Assembly

Mounting Plate

Screws

Align tabs with

holes in collar.

K (x2)

P (x2)

180°

Is the door edge chiseled?

Is the slotted hole centered in the door hole?

Hold the latch in front of the door hole, with

the latch face lush against the door edge.

YES

Install latch in door with

supplied screws.

No adjustment is

required. Proceed

to next step.

slotted hole

is centered

slotted hole is

NOT centered

Rotate latch face as

shown to extend latch.

Install latch in door with

wood block and hammer.

Install strike on the door frame.

chiseled

not

chiseled

Make sure

slotted hole is at

bottom of latch.

Make sure

slotted hole is at

bottom of latch.

Ensure collar

snaps into place.

Pull collar to test

for tight it.

unlocked

1 / 4

66895

Rev 03

Installation and User Guide

Kwikset

Technical Support

1-800-327-5625

www.kwikset.com

ENGLISH

Use a lathead screwdriver to

lift tabs on collar of rectangular

face to remove it from latch.

Install drive-in collar.

IMPORTANT: Make sure the latch bolt is fully

retracted (in the unlocked position).

Summary of content (4 pages)

PAGE 1
66895 Rev 03 Parts List Strike Drive-In Collar ENGLISH Latch A SmartKey Tool B Exterior Assembly Installation and User Guide C Keys D Mounting Plate E F Interior Assembly G H Required tools 4 AA Batteries Ruler 1-800-327-5625 www.kwikset.
PAGE 2
3 Prepare keypad and mounting plate (only for doors with smaller holes) What is the diameter of the hole in the door? Diameter is 2-1/8" (54 mm) Diameter is 1-1/2" (38 mm) or 2-1/8" 1-1/2" 54 mm 38 mm A No adjustment is required. Proceed to step 4. Remove adapter ring from exterior assembly: E 1. Remove gasket. B 2. Remove adapter ring from exterior assembly. 3. Reinstall gasket, ensuring tight seal.
PAGE 3
5 A Install interior assembly B Remove the battery cover. Load 4 AA batteries into the interior assembly. For best results, use new, nonrechargeable Alkaline batteries only. C Press and hold the Reset button on the interior assembly for 5 seconds, until you hear 3 long beeps. F Make sure the torque blade is still in the horizontal position and install the interior assembly. J H Note: Turnpiece may move on its own. H D Align the colored edges of the connectors and ensure a tight cable connection.
PAGE 4
8 Quick Setup and Use Move swiftly during programming. If no digit is pressed for 10 seconds, the system will time out and you will need to restart the procedure. A How to delete all User Codes B CAUTION: A User Code is used to unlock the door while a Mastercode is a password for making changes to the lock features. 1. Make sure the lock is unlocked and the door is open. . You will hear one beep. 1. Make sure the lock is unlocked and the door is open. 2.