Deadbolt Installation Guide

ManualsBrandsKwikset ManualsHardwareTustin Passage Lever and 910 Contemporary SmartCode Keypad Deadbolt Combo Pack with SmartKey and Z-Wave Technology

ENGLISH

A B C

12"

305 mm

Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave

controller, and initiate the Inclusion process at the controller. Refer to your

Z-Wave control system instructions for more information.

Press button “A” on the lock one time to include it in your system. The

controller and lock must remain stationary for a total of 60 seconds during

the Inclusion process.

If Inclusion is unsuccessful, initiate the Exclusion process at the controller,

then press button “A” on the lock one time. Once the lock is fully excluded

from the system, repeat the Inclusion process.

“Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller.

ZigBee locks: Perform the Inclusion process after installation is complete.

See “Z-Wave and ZigBee Systems” on the reverse side of this document.

Button

“A”

Z-Wave

Controller

Z-Wave locks only: Perform the Inclusion process

C D

P (2x)

Ensure tight cable connection.

Lay cable

at against

the interior

housing.

Install interior assembly

A B C

R (3x)

If needed, re-key the lock to

work with your existing key.

See the supplied SmartKey

Re-key instructions for more

information.

ball

tip

Keep “S” in a safe place, as you will

need it to access the back panel for

additional programming.

Select models only:

Install the battery cover and re-key the lockProgram the lock

Programming

instructions are

located on the

reverse side of

this document.

D (2x)

Install strike

A / A2

Extend latch bolt

Kwikset

1-866-863-6584

www.kwikset.com

If needed, please contact

Kwikset to order a drive-in

latch for your lock.

Parts in the Box

Latch and Strike Exterior Assembly Interior Assembly

Select models only:

25 mm

2-1/8"

54 mm

1-1/2"

38 mm

1-3/8" — 1-3/4"*

35 mm — 44 mm*

Check dimensions

Additional door preparation may be

required for doors with 1-1/2" (38 mm)

holes. Consult the drilling instructions at

www.kwikset.com/doorprep.

*Service kits for 2-1/4"

(57 mm) thick doors are

available through Kwikset.

2-3/8" (60 mm)

2-3/4" (70 mm)

2-1/8"

54 mm

1-1/2"

38 mm

Prepare exterior keypad

For doors with 2-1/8" (54 mm) holes

For doors with 1-1/2" (38 mm) holes

A B

C D

Q (2x)

Cable goes

underneath latch

Route cable

through center hole,

then push cable

into side hole.

center hole

side hole

Keep parallel to

edge of door

Tighten

screws

evenly

Insert key and test latch.

If latch does not extend or

retract smoothly, adjust

screws (Q).

Remove key when nished

and make sure the latch

bolt is fully extended.

Install keypad and mounting plate

B C

Make sure

turnpiece is

in the vertical

position.

Disassemble interior assembly and load battery pack

Ensure correct polarity. For best results,

use new non-rechargeable Alkaline

batteries only.

Do not install

battery pack yet!

Use and programming

instructions are located on the

reverse side of this document.

Required Tools

Additional Tools (depending on application)

Installation Guide

180°

A B

A / A2

Hold the latch in front of the

door hole, with the latch face

ush against the door edge.

If the latch holes are

centered in the door hole, no

adjustment is required.

Proceed to step 4.

If the latch holes are NOT

centered, adjust latch. See

“Latch Adjustment.”

Latch Adjustment (only if needed)

Adjust the backset of latch (if needed)

C (2x)

C D

Install latch

For doors with chiseled edge For doors without chiseled edge

wood

block

1-3/4" (44 mm)

1-3/8" (35 mm)

2-1/4" (57 mm)

2-3/8" (60 mm)

2-3/4" (70 mm)

Fold

If your door requires drilling, cut out the template and place it on the exterior side of the door.

Complete door drilling instructions are available on the SmartCode deadbolt page of www.kwikset.com.

Template

Edge

Backset

Face

Centerline

A B

Press and hold the

Lock button while

installing battery

pack (L).

Hold button until the

latch bolt starts

moving on its own.

This step will teach your lock the orientation of your door

and is crucial to lock operation.

HOLD

latch bolt

Did the latch bolt retract

and extend on its own

when the battery pack

was installed?

Door handing process

was successful!

Proceed to Step 11

after latch bolt stops

moving.

Remove battery pack,

wait 15 seconds, then

attempt the process

again.

YES NO

Perform door handing process

11 12 13

3 4 5 6

7 8

1 2

61019 / 02

Summary of content (2 pages)

PAGE 1
61019 / 02 1 Parts in the Box ENGLISH Latch and Strike Exterior Assembly B L D E 2-3/8" (60 mm) or 2-3/4" (70 mm) K 1-3/8" — 1-3/4"* 35 mm — 44 mm* 2-1/8" 1-1/2" or 54 mm 38 mm N F 1" 25 mm A2 Use and programming instructions are located on the reverse side of this document. Additional Tools (depending on application) G If needed, please contact Kwikset to order a drive-in latch for your lock. Kwikset 1-866-863-6584 www.kwikset.
PAGE 2
61019 / 02 A B SmartCode at a Glance ENGLISH Exterior Note: Although the arched 910 model is illustrated, instructions are the same for all 910 models. C Normal Operation Unlocking the Door Interior (cover removed) Lock Inclusion Tip: You can press the Lock button before entering your user code to light up the keypad at night. User Guide Kwikset Keypad Lock button 1-866-863-6584 www.kwikset.com ZigBee: Initiate the Inclusion process at your ZigBee controller.