INSTALLATION GUIDE Seda™ Single Lever Basin Faucet FUS-1821 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
7/8” (22mm) 19.7º 10 1/8” (257mm) ∅ 1 15/16” Prior (∅ 50mm) ∅ 1 3/4” (∅ 45mm) • ∅ 1 15/16” (∅ 50mm) • 8 5/16” (21mm) to Installation: 1 3/8” (35mm) Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800775-0703 for a replacement Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List E A F D B C1 C2 C3 C4 A. Faucet Body D. Hot & Cold Waterlines B. Base O-Ring (factory-installed) E. Adjustable Aerator C. Mounting Hardware: F. Aerator Key C1. Rubber U-Washer G. Hex Wrench C2. Metal U-Washer C3. Mounting Screw C4.
Faucet Dimensions 6” 152mm 5” 127mm 5.03” 128mm 6.8” 173mm 7.2” 183mm 1.37” MAX 35 mm 2.4” 61mm 1.37” 35 mm 1.
Lift Rod Drain Diagram and Parts List and Dimensions a b c p d e o f g h i 6 j n k l m a. Waste Stopper i. Top Hat Washer b. Drain j. Drain Off Pole c. Rubber Washer k. Washer d. Concave Washer l. Retaining Nut e. Plastic Washer m. Extender Rod f. Mounting Nut n. Clip g. Tailpipe Washer o. Thumb Screw h. Tailpipe p.
Step 1: Remove mounting hardware and install waterlines Remove faucet, mounting hardware, and waterlines from the box. Remove mounting nut (C4) from mounting screw (C3). Place faucet body (A) on a soft cloth, spout facing up. Secure A hot & cold waterlines (D) at the C3 base of the faucet (hand-tighten, then secure with ¼ turn of adjustable D wrench) A. Hot Side: Left B.
)xaM mm 5.24( Step 3: Secure faucet A2-FNU81-4/1 1 FENU81-”61/9 A7 ”8 /5 1 ~ ”61 /1 1 mm3 .14 ~ mm72 A A8 B8 C8 D8 C4 C3 Install rubber U-washer (C1) E and metal U-washer (C2) from F underneath the countertop or D sink. Attach mounting nut (C4) to mounting screw (C3) and tighten with adjustable wrench or 10mm wrench until snug A7 A8 B8 C8 C3 )xaM mm 5.24( D8 C1 C2 C4 Step 4: Connect waterlines to main valve A7 ”8/5 1 ~ ”61/1 1 mm3.
Step 5: Install Drain • Install drain (b), with rubber washer (c) attached, into the drain hole. Attach concave washer (d) with narrow end up, plastic washer (e), and mounting nut (f ) to drain (b) from underneath countertop or sink. Secure tightly to sink with an adjustable wrench b c b d e f g h • Thread tailpipe (h) onto drain (b) and hand-tighten.
Step 5: Install Drain • Insert lift pole rod (p) through the hole in the back of the faucet body. Loosen thumb screw (o) andbattach extender rod (m) toglift pole rod (p). h (o) Tighten thumb screw b c d e f p o o p n m b g h o p n j k l • Insert shortest end of drain off pole (j) into drain aoff pole opening of tailpipe (h). Make sure drain off b pole (j) and slot on waste stopper (a) engage. Attach washer (k) and p retaining nut (l) through drain off o l pole (j).
Step6: Flush faucet Remove adjustable aerator (E) with aerator key (F). Turn water on for 1 minute to remove any debris. Reassemble aerator (E) and adjust to desired position E F Replacement Part List - FUS-1821 1 2 3 17 4 5 6 7 8 16 14 15 9 10 11 12 13 1. Metal Handle 2. Set Screw 3. Cartridge Cover 4. Cartridge Sleeve 5. Metal O-Ring 6. Rubber Washer 7. Locking Nut 8. Cartridge 9. Base O-Ring 10. Rubber U-Washer 11. Metal U-Washer 12. Mounting Nut 13. Mounting Screw 14. Adjustable Aerator 15.
Replacement Part List - Lift Rod Drain 1. Waste Stopper 2. Drain 1 3. Rubber Washer 4. Concave Washer 5. Plastic Washer 2 3 6. Mounting Nut 16 7. Tailpipe Washer 4 8. Tailpipe 9. Top Hat Washer 5 15 6 10. Drain Off Pole 11. Washer 7 12. Retaining Nut 8 9 10 1112 14 13 13. Extender Rod 14. Clip 15. Thumb Screw 16.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE 10 Leakage under the handle 9 11 Locking nut (7) has come loose Hexagon Nut 12 13 ACTION Loosen set screw (2) with hex wrench (17). Remove metal handle (1), cartridge cover (3), cartridge sleeve (4), metal o-ring (5) & rubber washer (6).
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1M 1.2GPM 4.5L/min maximum TM Water Efficiency FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. COMMERCIAL WARRANTY Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
