REM OT E CON T ROLLER OWNER’S MANUAL IMPORTANT NOTE: Thank you for purchasing our air conditioner. Please read this manual carefully before operating your new air conditioning unit. Make sure to save this manual for future reference.
Table of Contents Remote Controller Specifications ......................................................02 Handling the Remote Controller ....................................................03 Buttons and Functions ...................................................................04 Remote Screen Indicators ..............................................................09 How to Use Basic Functions ..........................................................10 How to Use Advanced Functions ..................
Remote Controller Specifications M odel RG51F/EF, RG51F2(1)/EFU1, RG51F4/E, RG51F5(1)/EU1, RG51H(1)/EF, RG51H1(1)/EF, RG51H2(1)/EFU1-M, RG51H3(1)/EU1-M, RG51F6/E Rated Voltage 3.
Handling the Remote Controller Inserting and Replacing Batteries Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use. 1. Slide the back cover from the remote control downward, exposing the battery compartment. 2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment. 3. Slide the battery cover back into place.
Buttons and Functions Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual. 1 TEMP : Decreases temperature in 1°C increments. Min. temperature is 17°C. 2 TEMP : Increases temperature in 1°C increments. Max. temperature is 30°C. 3 ON/OFF: Turns the unit on or off.
1 TEMP : Decreases temperature in 1°F increments. Min. temperature is 62°F. 2 TEMP : Increases temperature in 1°F increments. Max. temperature is 86°F. 3 ON/OFF: Turns the unit on or off. 2 4 FAN SPEED: Selects fan speeds in the following order: AUTO LOW MED HIGH 5 4 5 MODE: Scrolls through operation modes as follows: AUTO COOL DRY HEAT FAN 7 9 6 8 10 11 12 1 3 I SENSE NOTE: Please do not select HEAT mode if the machine you purchased is cooling only type.
1 TEMP : Decreases temperature in 1°F increments. Min. temperature is 62°F. 2 TEMP : Increases temperature in 1°F increments. Max. temperature is 86°F. 3 ON/OFF: Turns the unit on or off. 1 2 3 4 5 SHORT CUT 9 6 8 10 11 12 7 I SENSE 4 FAN SPEED: Selects fan speeds in the following order: AUTO LOW HIGH 5 MODE: Scrolls through operation modes as follows: AUTO COOL DRY HEAT FAN NOTE: Please do not select HEAT mode if the machine you purchased is cooling only type.
1 TEMP : Decreases temperature in 1°C increments. Min. temperature is 17°C. 2 TEMP : Increases temperature in 1°C increments. Max. temperature is 30°C. NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F. 3 ON/OFF: Turns the unit on or off.
1 1 TEMP : Decreases temperature in 1°C increments. Min. temperature is 17°C. 2 TEMP : Increases temperature in 1°C increments. Max. temperature is 30°C. 3 ON/OFF: Turns the unit on or off. 4 FAN SPEED: Selects fan speeds in the following order: AUTO LOW MED HIGH 5 MODE: Scrolls through operation modes as follows: AUTO COOL DRY HEAT FAN NOTE: Please do not select HEAT mode if the machine you purchased is cooling only type. Heat mode is not supported by the cooling only appliance.
Remote Screen Indicators Information are displayed when the remote controller is power up. Mode display DRY COOL AUTO HEAT AUTO FAN COOL HIGH Displayed when data transmitted. DRY MED Displayed when remote controller is ON.
How to Use Basic Functions ATTENTION Before operation, please ensure the unit is plugged in and power is available. AUTO Mode Select AUTO mode Set your desired temperature Turn on the air conditioner MODE ON/OFF NOTE: 1. In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT function based on the set temperature. 2. In AUTO mode, fan speed can not be set.
Setting the TIMER TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off. TIMER ON setting Press TIMER ON button to initiate the ON time sequence. Press Temp. up or down button for for multiple times to set the desired time to turn on the unit. Point remote to unit and wait 1sec, the TIMER ON will be activated.
How to Use Advanced Functions Swing function(some units) Press Swing button 2s SWING SWING The horizontal louver will swing up and down automatically when pressing Swing button. Press again to make it stop. Keep pressing this button more than 2 seconds, the vertical louver swing function is activated. (Model dependent) SLEEP function SLEEP The SLEEP function is used to decrease energy use while you sleep (and don t need the same temperature settings to stay comfortable).
SHORTCUT function(some units) SHORT CUT Used to restore the current settings or resume previous settings. Push this button when remote controller is on, the system will automatically revert back to the previous settings including operating mode, setting temperature, fan speed level and sleep feature(if activated).
The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.
Iloilo Office: Door 8 & 9 NSB Bldg., Rizal St reet , Lapuz, Iloilo Cit y Tel No.: (033) 330-2926 Koppel Head Office: 106 Indust ry Drive, Carmelray Indust rial Park 1, Brgy. Canlubang, Calamba Cit y, Laguna 4028 Tel No.: (02) 8823-88-83 Websit e: w w w .koppel.ph Cebu Office: Door 1 & 2 Rozen Bldg., A. Cort ez Avenue, M andaue Cit y Tel No.: (032) 346-7278 Fax No.: (032) 346-7279 Davao Office: J.P. Cabaguio Avenue, Davao Cit y Tel No.: (082) 221-6419 Fax No.
