Installation Guide

ManualsBrandsKohler ManualsPlumbingRevel 70" High x 35-1/8 - 40" Wide Pivot Frameless Shower Door with Thick Clear Glass

9/64"

5/32"

1/4"

1/4", 5/16"

Masonry Bit

for Tile

Masking Tape

100% Silicone Sealant

Miter Box

32 Teeth Per Inch Blade

Pliers

Tin Snips

Step Stool

3/16" Hex Wrench

Anchor

Pivot Jamb

Screw

#10-16 x 1-1/2"

Jamb Cover

Screw

1/4"-20

Handle Assembly

Door Panel

Fixed Panel

Wall Jamb Seat

Bottom Frame

Threshold Seal

Threshold

Strike Jamb Seat

Pivot Seat

Strike Jamb

Top Bracket

Top Clamp Assembly

Bottom Clamp Assembly

Top View

Right Pivot

Showerhead

Handle

Strike Side

Left

Pivot

Screw

1/4"-20 x 1-1/2"

Right

Pivot

Strike Jamb

Seat

Wall

Threshold

Top View

Threshold

Tape

Silicone

Sealant

Wall Jamb

Seat

Pivot

Seat

Bottom

Frame

Strike Jamb

Seat

Top View

Left Pivot

Showerhead

Strike Side

Handle

Tape Measure

Cut here.

"A" Mark

Threshold

1/16"

(2 mm)

Showerhead

Side

1/4"

(6 mm)

Wall

Top View

Threshold

Screw

#10-16 x 1-1/2"

Pivot Door

Do not remove the corner protectors on the glass panels until

instructed to do so.

Walls must be within 3/8” (10 mm) of plumb.

Cover the drain with tape to avoid loss of small parts.

Follow the silicone sealant manufacturer’s instructions for

application and curing time.

Right Side Pivot

IMPORTANT: Left side pivot configuration is shown

in installation steps unless otherwise indicated.

Determine the pivot side of your installation.

Right side pivot is shown below.

Left Side Pivot

Left side pivot is shown below.

IMPORTANT: Left side pivot configuration is shown

in installation steps unless otherwise indicated.

Cut the Threshold

Confirm the height of the opening is adequate. Consult

the specification sheet for a specific height requirement.

Measure distance “A.” Mark and cut the threshold

1/16” (2 mm) or the width of a saw blade less than “A.”

Prepare the Threshold

Position the threshold 1/4” (6 mm) from the front of the

ledge. Mark the location.

Remove the threshold.

If needed, file the ends to match the corners and remove

burrs.

Assemble the Threshold

On the pivot side, slide the:

 pivot seat

 bottom frame

 wall jamb seat

into the channel. On the opposite side of the threshold

slide the:

 stike jamb seat

over the threshold.

Install the Threshold

Apply a 1/4” (6 mm) bead of silicone sealant along the

ledge under the threshold location.

Install the threshold on the ledge.

Push the strike jamb seat tight against the wall. Secure

the threshold with tape.

Install the Top Bracket

Position the top bracket on the pivot jamb. Orient as

shown.

Start both screws, then fully tighten with a #3 Phillips

screwdriver or 3/16” flathead screwdriver.

TIP: If the space above the door is limited, use a short

or ratcheting screwdriver.

Mark the Hole Locations

Move the pivot jamb into place.

Plumb the pivot jamb, tape in place, and starting at the

top, mark six hole locations.

Do not mark the bottom hole.

NOTE: The bottom hole will not be used.

Drill the Holes

IMPORTANT: Use the correct style drill bit for the wall

material.

Drill 5/16” holes at each mark.

Install the provided anchors.

Install the Pivot Jamb

Install the pivot jamb and secure tightly.

For the top screw, use a long handle screwdriver to

avoid damaging the finish.

1246188-2-D

Installation and Care Instructions

For care and cleaning and other information, visit www.us.kohler.com.

For service parts information, visit www.kohler.com/serviceparts.

Record the model number from box for reference.

Model Number:______________

Required Tools Parts Identiﬁ cation

K-707500, K-707501, K-707506, K-707510, K-707511, K-707516, K-707531, K-707536, K-707541, K-707546, K-707551, K-707556

NOTICE: Do not touch the edges of the tempered glass with

tools or any other hard objects. Do not set the unframed

tempered glass directly on the floor or any hard surface.

IMPORTANT! Leave this manual for the end user.

Read these instructions before installing or using this product.

1 2

1246188-2-D

USA/Canada: 1-800-4KOHLER

México: 001-800-456-4537

kohler.com

WARNING: Risk of serious injury. Damage prior to

installation can result in glass shattering. Inspect the

glass and all parts for damage before installation.

WARNING: Risk of serious injury. Improper

installation can result in glass shattering. Follow all

installation instructions.

WARNING: Risk of serious injury. Do not cut

tempered glass. Tempered glass will shatter if cut.

WARNING: Risk of serious injury. Shower door and

side panels can shatter. Regularly inspect the glass and

all parts for damage, missing, or loose parts.

WARNING: Risk of serious injury. Always wear

safety glasses while cutting and drilling.

WARNING: Risk of product and property damage.

This shower door is very heavy. Do not install it to

plastic shower modules or drywall unless additional

support is provided behind the wall.

Summary of content (6 pages)

PAGE 1
Installation and Care Instructions Pivot Door K-707500, K-707501, K-707506, K-707510, K-707511, K-707516, K-707531, K-707536, K-707541, K-707546, K-707551, K-707556 1246188-2-D Required Tools For care and cleaning and other information, visit www.us.kohler.com. For service parts information, visit www.kohler.com/serviceparts. Parts Identification Record the model number from box for reference. Model Number:______________ USA/Canada: 1-800-4KOHLER México: 001-800-456-4537 kohler.
PAGE 2
11 Install the Wall Cover 12 Snap the wall jamb cover into place. Assemble the Pivot Seat Position the cam on the pivot seat. The pin should be on the side opposite the bottom frame. NOTE: The pin would be on the opposite side for a right side pivot configuration. Position the pivot seat tight against the bottom frame. 13 Assemble the Top Clamp Assemble the bushing to the top clamp. Set aside until instructed. Do not install until instructed.
PAGE 3
Instructions d'installation et d'entretien Porte pivotante K-707500, K-707501, K-707506, K-707510, K-707511, K-707516, K-707531, K-707536, K-707541, K-707546, K-707551, K-707556 1246188-2-D Outils requis Pour tout renseignement sur l'entretien, le nettoyage et autre, visiter www.us.kohler.com. Pour tout renseignement sur les pièces de rechange, visiter www.kohler.com/serviceparts. Identification des pièces Noter le numéro de modèle sur le carton d'emballage à titre de référence.
PAGE 4
11 Installer le revêtement mural Enclencher le revêtement du montant de mur en place. 12 Assembler le siège du pivot Placer la came sur le siège du pivot. La goupille doit se trouver sur le côté opposé du cadre inférieur. REMARQUE: La goupille serait sur le côté opposé pour une configuration de pivot côté droit. Positionner le siège du pivot de manière bien serrée contre le cadre inférieur. 13 Assembler la bride supérieure Assembler la bague sur la bride supérieure.
PAGE 5
Instrucciones de instalación y cuidado Puerta pivotante K-707500, K-707501, K-707506, K-707510, K-707511, K-707516, K-707531, K-707536, K-707541, K-707546, K-707551, K-707556 1246188-2-D Herramientas requeridas Para consultar el cuidado y la limpieza, y obtener más información, visite www.us.kohler. com. Para consultar información sobre piezas de repuesto, visite www.kohler.com/serviceparts. Identificación de piezas Anote el número de modelo de la caja como referencia.
PAGE 6
11 Instale la cubierta de la jamba mural Meta a presión la cubierta de la jamba mural en su lugar. 12 Ensamble el asiento del pivote Coloque la leva en el asiento del pivote. El pasador debe quedar en el lado opuesto del marco inferior. NOTA: El pasador quedaría en el lado opuesto en el caso de una configuración con el pivote del lado derecho. Coloque el asiento del pivote justo contra el marco inferior. 13 Ensamble el sujetador superior Ensamble el buje al sujetador superior.