Installation Guide

Front View
Pin
Cam
Pin
Cam
Pivot Seat
Bottom
Frame
Pin Seat
Setscrews
Top Clamp
Bushing
Pin
Cam
Bottom Clamp
Setscrews
Label
Top
Clamp
B – 1/16" (2 mm)
Inside of
Door
Safety Stop
Bottom
Clamp
Inside of
Door
C – 1/16" (2 mm)
Underside of
Bottom Clamp
Safety Stop
Strike Jamb
Strike Jamb
Seat
Countersink
Washer
Screw
Nylon
Washer
Pivot
Threshold Seal
Side View
Shower
Interior
Door Panel
Strike Jamb
Bottom
Clamp
Water
Deflector
1/2" (13 mm)
Adhesive
Backing
Adhesive
Backing
Apply tape to both
sides of door panel.
Mark the vertical center
of the door.
Cam
Front
Edge
Tape
Measure
B
C
Bracket
Front
Edge
Pivot Seat
Bottom
Frame
Install the Wall Cover
Snap the wall jamb cover into place.
Assemble the Pivot Seat
Position the cam on the pivot seat. The pin should be on
the side opposite the bottom frame.
NOTE: The pin would be on the opposite side for a
right side pivot configuration.
Position the pivot seat tight against the bottom frame.
Assemble the Top Clamp
Assemble the bushing to the top clamp.
Set aside until instructed.
Do not install until instructed.
Assemble the Bottom Clamp
Assemble the cam to the bottom clamp.
Set aside until instructed.
Do not install until instructed.
Measure the Opening
Measure from the wall to the front of the top bracket,
distance “B,” and record it.
Measure from the wall the front of the pivot seat
distance “C” and record it.
Unpack the door panel. Place it on protective material.
IMPORTANT! Do not remove the door panel corner
protectors until instructed.
Install the Top Clamp
On the same side as the safety stop, position the top
clamp on the top of the door panel with the setscrews
on the side opposite the CleanCoat® label.
Position the front edge of the top clamp pivot 1/16” (2
mm) less than dimension “B.”
Carefully tighten the setscrews 1/4 turn past handtight
with a 3/16” hex wrench.
Install the Bottom Clamp
On the same side as the safety stop, position the
bottom clamp on the bottom of the door panel with the
setscrews on the side opposite the CleanCoat® label.
Position the front edge of the bottom clamp pivot
1/16” (2 mm) less than dimension “C.”
Carefully tighten the setscrews 1/4 turn past handtight
with a 3/16” hex wrench.
Position the Pivot Seat
Slide the pivot seat away from the bottom frame to the
middle of the door opening.
Install the Door Panel
Move the door panel into position over the pivot seat
and lower into place.
With the door in the open position, tilt the door and
align the top clamp with the hole in the top bracket.
Lift the door panel slightly and slide the bottom pivot
while engaging the top pivot in the top bracket.
Make sure the bottom pivot is tight against the bottom
frame.
Secure the Door Panel
Position the nylon and countersink washer over the
pivot.
Secure with the screw. Tighten securely.
TIP: If the space above the door is limited, use a short
or ratcheting screwdriver.
Remove the corner protectors.
Adjust the Door Panel
Test the door for smooth operation.
Confirm the door is correctly aligned. There should be a
gap of less than 1/4” (6 mm) from the wall opposite the
door panel.
If the door panel needs adjustment, support the front
edge of the door panel and loosen the top or bottom
pivot clamp setscrews and slide the door forward or
back as needed.
Retighten the setscrews when correctly aligned.
Prepare the Strike Jamb
Move the clear plastic strike jamb into place.
Close the door and align the strike jamb with the door.
Mark the location with a pencil.
Remove the strike jamb.
Install the Strike Jamb
Thoroughly clean the wall where the strike jamb will be
applied with alcohol pads or denatured alcohol.
Allow the area to dry.
Remove the backing from the adhesive strip on the
strike jamb.
Carefully install the strike jamb.
Install the Seal
Measure from the front edge of the bottom clamp to the
front edge of the door panel. Cut the seal to 1/2” (13
mm) less than that length.
Measure from the back edge of the bottom clamp to the
edge of the panel.
Cut the excess seal to that length. Install both sections,
water deflector toward the shower interior.
Install the Fixed Panel
Apply silicone sealant to the back channel in the pivot
jamb, along the inside side of the pivot jamb, and along
the bottom frame.
Remove the corner protectors if installed.
Move the fixed glass panel into place in the channel.
Confirm the glass panel has silicone sealant along the
entire length.
Apply tape to keep the panel stable.
Prepare the Handle
Determine the vertical center of the door panel. Mark
the location on the front edge of the door panel.
Thoroughly clean the door panel at the handle location
with the provided alcohol wipe.
Allow the area to fully dry.
Tape the template into place with the top of the
template aligned with the mark.
Install the Handle
Remove the adhesive backing from one of the handles.
Carefully position the handle in the installation position
and press firmly.
Repeat with the second handle.
Seal the Threshold
Remove the tape from the threshold.
TIP: If silicone sealant needs to be removed, use
denatured alcohol.
Apply silicone sealant to both sides of the strike jamb.
IMPORTANT: Block the door so it cannot close until
the sealant has cured.
Seal the Pivot Jamb
From inside the shower, apply silicone sealant to the
pivot jamb where it meets the wall.
Seal the Threshold
From outside the shower, apply silicone sealant along
the front of the threshold. Allow the sealant to dry
following the sealant manufacturers instructions.
Troubleshooting
Symptom: The door is too tall for the opening. Recommended Action
1. The shower door does not fit in the opening. A. You have the wrong size door. Return the door and exchange it for a model that fits.
2. The door fits in the opening, but the top screws cannot
be tightened.
A. Use a short barrel screwdriver or ratcheting screwdriver to tighten the screws.
B. You have the wrong size door. Return the door and exchange it for a model that fits.
Symptom: Noise or rattling when door is used. Recommended Action
1. The side panel rattles in the wall jamb. A. Apply additional silicone sealant to the area where the side panel and wall jamb connect. Allow 24 hours to dry before using.
2. There is a squeak at the bottom hinge. A. Replace the cam in the pivot seat. The pin was likely bent during installation.
Symptom: Water leak. Recommended Action
1. Water leaks under the door panel.
A. Confirm the bottom seal is properly installed. Confirm there is a seal on both sides of the bottom clamp. Check the gap between
the threshold and the glass. Adjust if needed. Confirm the bottom clamp is correctly engaged with the cam.
2. Water leaks between the wall and the wall jamb or strike
jamb.
A. Silicone both sides where the wall meets the wall jamb of the leaking jamb. Allow 24 hours to dry before using.
3. Water leaks between the side panel and wall jamb. A. Silicone both sides of the wall jamb to side panel seam. Allow 24 hours to dry before using.
Symptom: Unable to install the door panel. Recommended Action
1. Top bracket is installed backwards. A. Reinstall the top bracket oriented as shown in the instructions.
2. The wall jamb seat was not installed. A. Remove all door components. Install the wall jamb seat in the threshold. Reinstall the parts following the instructions.
Symptom: Door will not close. Recommended Action
1. The cam on the pivot seat is installed backwards.
A. Remove the door panel by performing steps 19 and 18 in reverse. Turn the cam on the pivot to match the orientation in step 12.
Perform steps 18 and 19 in the correct order.
Symptom: Incorrect alignment. Recommended Action
1. There is a gap between the door panel and the wall jamb
or strike jamb that is too large or wider at the top or
bottom.
A. Perform the adjustment steps in step 21 until the final adjustment is reached.
21246188-2-D ©2016 Kohler Co.
11 12
17
13
1816
14
19
15
20
Warranty
ONE-YEAR LIMITED WARRANTY
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from date of
installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses any such
defects occurring in normal usage within one (1) year after installation. Kohler Co. is not responsible for removal or installation
costs. Use of in-tank toilet cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or E-tailer, or by
writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or by calling 1-800-4-KOHLER
(1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within Mexico, or visit www.kohler.com within the
USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com in Mexico.
IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. KOHLER CO. AND/OR SELLER
DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do
not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential
damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You may also
have other rights which vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty.
22 2321 24 25
27 2826 29
30