Installation Guide

9/64"
5/32"
1/4"
1/4", 5/16"
Masonry Bit
for Tile
Masking Tape
100% Silicone Sealant
Miter Box
32 Teeth Per Inch Blade
Pliers
Tin Snips
Step Stool
1198346**
Skin Pack
Outside Roller
Inside Roller
Roller Cap Roller PlugClipScrew
#10-24 x 1-3/8"
Screw
#10-24 x 1-1/4"
1260190**
Wall Anchor
Alcohol
Wipe
Wall Jamb
Cap
Center
Guide
Screw
#6-20 x 1/4"Cleat
Skin Pack
1260250* (Center Guide)
Bubble Pack
Screw
#8-18 x 3/8"
Screw
#8-18 x 1-1/2"
Screw
#10-16 x 1-1/2"
Bumper
Anchor
1042520-G (#8-18 x 3/8")
Screw
Header
1077762
Anchor
1262336
Inside Roller
Screw
Screw
Towel Bar
Center Guide
1093027
Washer (8 ea.)
1049033-D
Screw
1197566-01**
Retainer
1187908**
Roller Cap
1049043-D
Screw
1181060**
Wall Jamb Cap
1208955**
Clip
1195781**
Roller Plug
1188940-01**
Cleat
1186360**
Bumper Cover
Wall Jamb
1187908**
Roller Cap
1262337
Inside Door Panel*
Outside Door Panel*
Threshold
1187796**
Handles with
Templates
#6-20 x 1/4"
1197564-01** [60" (1524 mm)]
1197564-02** [48" (1219 mm)]
1048208-C (#8-18 x 1-1/2")
1198328-A
1262423-01** [58" (1473 mm)]
1262423-02** [70" (1778 mm)]
1262423-03** [56" (1422 mm)]
1262423-04** [78" (1981 mm)]
1057704-01**
1057704-03**
[24" (610 mm)]
[18" (457 mm)]
1263090**
1179922-01** [60" (1524 mm)]
1179922-02** [48" (1219 mm)]
1264187-01**
[58" (1473 mm)]
1264187-02** [78-1/4" (1988 mm)]
Seal (Service Only)
#10-16 x 1-1/2"
Outside
Roller
(#10-24 x 1-1/4")
1260672
Wall Anchor
1260672
Wall Anchor
Cut Line
"A" Mark
1/4"
(6 mm)
A
A
x2
1"
(25 mm)
x2
2-1/2"
(64 mm)
#10-16 x 1-1/2"
1/8"
(3 mm)
x2
x2
2
1
3
Centerline
Centerline
Groove
Mark
Center
Punch
Sliding Bath and Shower Doors
Walls must be within 3/8” (10 mm) of plumb.
Follow the silicone sealant manufacturer’s instructions for
application and curing time.
Measure the Ledge:
Confirm the ledge is at least 2-1/2” (64 mm) wide. Do
not install the door if there is not 2-1/2” (64 mm) of
width.
Cover the drain with tape to avoid loss of small parts.
Measure and Cut the Threshold:
Measure distance “A.”
Mark distance “A” on the threshold.
Subtract 1/4” (6 mm) from “A” and make a second
mark.
Cut the threshold at the second mark.
Position the Threshold:
If needed, file the ends of the threshold to match the
corner radius. The threshold must sit flat.
Install the threshold as close to the front of the ledge as
possible. Mark the location.
Tape the threshold in place.
Mark the exact center of the shower ledge.
Install the Center Guide:
Clean the center guide location behind the threshold
with an alcohol wipe.
Remove the backing (1) from the adhesive strips on the
center guide.
Align and rotate the center guide into place (2) with the
center marks on the guide and threshold aligned.
Press the center guide firmly into place (3).
Prepare the Wall Jambs:
IMPORTANT! The threshold and wall jamb must fit
tightly against the ledge and wall.
Position the wall jamb over the threshold.
If needed, trim and file the ends to match radius
corners.
Install the Wall Jambs:
Position the wall jambs over the threshold.
Plumb using a level.
Tape the wall jambs in place.
Locate the Wall Jamb Anchors:
On each side of the wall jamb, measure 1” (25 mm)
down and mark the side of the wall jamb.
Remove the wall jamb. Mark the center point between
the marks.
Tile Installations Only:
Mark the tile at the hole location before drilling by
carefully tapping the mark with a center punch. This
keeps the drill bit from moving as the hole is started.
When installing to a tile wall, first drill a small
diameter hole, then the correct size hole.
Install anchors. Do not install the screws directly into
the tile, as this may crack the tile.
When drilling, use a masonry bit.
Install the Top Wall Jamb Anchors:
Drill a 1/4” hole at each mark.
Install the provided wall anchors.
Install the two #10-16 x 1-1/2” screws, one for each
wall jamb, leaving a 1/8” (3 mm) gap between the
screwhead and the wall.
Install the Wall Jambs:
Slide each wall jamb onto the top screw, then down
over the threshold.
IMPORTANT! The jambs must be tight against the
wall. Adjust the screws as needed.
Sliding Shower DoorsSliding Bath Doors
1
1201264-2-E
1201264-2-E
Installation and Care Instructions
Need help? Contact the KOHLER Customer Care Center at 1-800-4KOHLER (1-800-456-4537)
For service parts information *
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
K-70600, K-706001, K-706002, K-706004, K-706005, K-706006, K-706008, K-706009, K-706014, K-706015
WARNING: Risk of serious injury. Damage prior to
installation can result in glass shattering. Inspect the
glass and all parts for damage before installation.
WARNING: Risk of serious injury. Improper
installation can result in glass shattering. Follow all
installation instructions.
WARNING: Risk of serious injury. Do not cut tempered
glass. Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and
side panels can shatter. Regularly inspect the glass and
all parts for damage, missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety
glasses while moving, installing, cutting, or drilling the
glass panels.
IMPORTANT! Do not touch the edges of the tempered glass
with tools or any other hard objects. Do not set the unframed
tempered glass directly on the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
NOTICE: The warranty does not apply to product that has
been modified or altered in a manner other than as expressly
permitted in the Installation and Care Guide.
Read and follow all instructions before installing or using this
product.
USA/Canada: 1-800-4KOHLER
México: 001-800-456-4537
kohler.com
1 2
7
3
86
4
9
5
10