COBALT COBALT and ‘ogo design ans trademarks or registered trademarks of LF, LLC. Al rights reserved. ITEM #2368776 72-IN WORK TABLE MODEL #0018004 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date customer service department at 1-888-COBALT (1-888-356-2258), 8am. 8 pm, EST, Questions, problems, missing parts? Before resuming to your retailer, call our Monday Sunday.
TABLE OF CONTENTS Package Come... IEEE 3 Hardware COMBS... cc err err ene eee ed 4 Safety Information Preparation oo. 4 Assembly INHIBITIONS. cur err rennet senses 5 Troubles Hooting «ooh ea 7 BRITANNIA ena 7 Replacement Parts LIES oceans 7 PRODUCT SPECIFICATIONS Maximum load for each hook 4 ibs. Maximum load for sate side panel 11 Ibs. Maximum load for wood top 1500 lbs. Maximum total load 1522 Ibs.
PACKAGE CONTENTS aE DESCRIPTION QUANTITY A Solid wood fop 1 B Side panel 2 C Left leg 1 Do Right leg 1 E Angle support 2 F Back strut 1 G Leg leveler assembly 4
HARDWARE CONTENTS (shown actual size) Bolt Bolt M6 mm Nut Qty. 8+2 Qty. 28+2 Qty. 2042 A SAFETY INFORMATION Please read and understand this entire manual before attempting fo assemble or operate this product. Failure to follow may result in serious injury. Save all warnings and instructions for future reference. A WARNING + Do not stand on, step on, or alter this unit for anything outside the designed function of usage. = Use care when handling and assembling metal plates.
ASSEMBLY INSTRUCTIONS 1. Attach side panels (B) to the solid wood top (A) with bolls (AA). Note: Be sure to keep the solid wood fop (A) upside down on a soft surface, such as carpeting or a piece of cardboard, to protect it from scratches. Ensure the bolts are screwed tightly. This applies to all the bolts used in this unit. Hardware Used @ wmex20mmeor ¥ x8 2. Determine the desired location for the right leg (D), insert it into side panel {B), and tighten with boils (BB) and M6 mm news (CC).
ASSEMBLY INSTRUCTIONS 3. Use bolts (BB) to fix age! supports (E) to side panels (B) and solid wood top (A). Place the unit upright. Hardware Used Bolt ¥ x8 4. Attach the back strut {F) to the back of the left leg (C) and right leg (D) with bolts (BB) and M8 mm nuts (CC). Carry the table to the desired place and see if the solid wood top (A) is level. If not due to uneven floor, use an adjustable wrench (not included) to adjust the hex nut until the top is level.
TROUBLESHOOTING retsina POSSIBLE CAUSE CORRECTIVE ACTION Bolivars) cannot align into the hole(s). into the hole(s). 1. Bolt is damaged. 2. Bolt does not go vertically 1. Change boll{s}. 2. Adjust the pairs and make sure the bolt(s) go vertically in to the hole(s). Work table is not stable enough. 1. Bolivars) loose. or too soft. 2. The ground is uneven 1. Fasten all bolts tightly by hex wrench or screwdriver. 2. Adjust the hex Putin the leg leveler assembly to offset the floor issue.
COBALTO LU REINES tn ERT va ARTICULO # 2368776 MESA DE TRABAJO DE 182,88 CM Modelo # 0019004 COBALTO y # disenso de! engollipe Son marcas compilarlas & Aras registradas de LF, LLC. Todos los derechos reservados. ADJUNTE SU RECIBO AQUÍ Rimero de serie Fecha de compra Departamento de Servicio al Cliente al 1888-COBALTO (1-888-356-2258), de lunes a ¢ Preguntas, problemas, piezas faltan tes? Antes de volver a la tienda, lame a nuestro domingo de 8 a.m. a 8 p.m, hora estándar de! Este.
CONTENIDO DEL PAQUETE rd LS DESCRIPCIÓN CANTIDAD A Cubierta de madera salida 1 B Pana! lateral 2 C Pata izquierda 1 D Pata derecha 1 E Soporte en triangulo 2 F Puntal posterior 1 G Conjunto nivelador de la pata 4
ADITAMENTOS (se muestran en mafioso real) Perno MB x20 mm Remo Tuerca Mé mm Can. B+2 Can. 28+2 Can. 20+2 A INFORMACIÓN DE SEGURIDAD Lea y comprenda completamente este manual antes de intentar ensamblar u operar este producto. No seguirla podría provocar lesiones serias. Guarde fados las advertencias e instrucciones para referencia futura. A ADVERTENCIA « No pise, modifique ni se pare sobre esta unidad para ningún uso que no sea la función de uso. = Tenga cuidado al manipular y ensamblar las placas de metal.
INSTRUCCIONES DE ENSAMBLAJE 1. Filie los paneles laterales (B) a la cubierta de madera salida (A) con peamos (AA). Nota: asegúrese de mantener la cubierta de madera salida (A) hacia abajo sobre una superficie suave, como una aforara oun rozo de cartón, para evitar rayaría. Asegúrese de que los pernos queden bien atornilladores. Esto se aplica a todos los pernos que se usen en esta unidad, Aditamentos utilizados @ Pomomsx20mm ¥ x8 2.
INSTRUCCIONES DE ENSAMBLAJE 3. Utilice pernos (BB) para fijar los soportes de ángel (E) a los paneles laterales (B) y la cubierta de madera salida (A). Coloque sl producto en posición vertical. Aditamentos utilizados Pero Sujete el puntal posterior (F) a la parte posterior de la pata izquierda (C) v la pata derecha (D) con parnos (BB) y tuercas M6 mm (CC). Nieve la mesa al lugar deseado y vea si la cubierta de madera salida {A} esta nivelada.
SOLUCIÓN DE PROBLEMAS asáis EY CAUSA POSIBLE ACCIÓN CORRECTIVA Los pernos no se 1. Los pernos estén da fiados. pueden alinear en los orificios. 2. Los pernos no se deslizan verticalmente en los orificios. 1. Cambie los peamos. 2. Ajuste las piezas y asegúrese de que los pernos se deslicen verticalmente en los orificios. La mesa de trabajo | 1. Los pernos estén sueltos. no es lo suficientemente 2. El suelo esta desnivelado o estable. es muy blando. 1.