Specification

23¹⁄₂ "
(59.7 cm)
84" (213.4 cm)
Power Cord
*83³⁄₈ "
(211.8 cm)
*3
¹⁄₂"
SIDE VIEW
25 ³⁄₈ "
(64.5 cm)
(8.9 cm)
DOOR SWING DIMENSIONS
The location must permit the door to open a minimum of 90°. Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the refrigerator and a corner wall.
NOTE: More clearance may be required if you are using overlay panels or custom handles.
Bottom Mount Built-in Refrigerator
PRODUCT MODEL NUMBERS
IMPORTANT: Observe all governing codes and ordinances.
Electrical: A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical
supply is required. It is recommended that a separate circuit serving only your
refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not
use an extension cord.
A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right
side cabinets or end panel.
Location: Do not install in a location where the temperature will fall below 55°F
(13°C). It is recommended that you do not install the refrigerator near an oven,
radiator, or other heat source.
■
Floor must support the refrigerator weight, more than 600 lbs. (272 kg), door
panels, and contents of the refrigerator.
■
Ceiling height must allow for side tipping radius. See “Tipping Radius.”
■
Location should permit door to open fully. See “Door Swing Dimensions.”
■
Location must permit top grille removal. See “Opening Dimensions.”
Water Supply:
A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa)
is required to operate the water dispenser and ice maker. If you have questions about
your water pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a reverse osmosis
system going to the water inlet valve of the refrigerator needs to be between 30 and
120 psi (207 and 827 kPa).
■
All installations must meet local plumbing code requirements.
■
The water shutoff should be located in the base cabinet on either side of the
refrigerator or some other easily accessible area. The right-hand side is
recommended. The access hole through the cabinet must be within ¹⁄₂" (12.7 mm)
of the rear wall.
NOTE: If the water shutoff valve is in the back wall behind the refrigerator, it must
be at an angle so that the tube is not kinked when the refrigerator is pushed into
its final location.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10721177A
12/4/14
KBBL206E
KBBL306E
KBBR206E
KBBR306E
KBFN402E
KBFN406E
KBFN502E
KBFN506E
24"
(60.96 cm) min.
1"
(2.54 cm)
6"
(15.2 cm)
6"
(15.2 cm)
6"
(15.2 cm)
PRODUCT DIMENSIONS
■
Height dimensions are shown with the leveling legs extended to ¹⁄₈" (3 mm)
below the rollers.
■
Width dimensions were measured from trim edge to trim edge.
FRONT VIEW
36" (91.4 cm) Single Door and
French Door Models
36¹⁄₄" (92 cm)
*83³⁄₈"
(211.8 cm)
42" (106.7 cm) Models
42¹⁄₄" (107.3 cm)
*83³⁄₈"
(211.8 cm)
* When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below
rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.
TOP VIEW
25³⁄₈"
(64.5 cm)
41¹⁄₄"
(105 cm)
Model Width A
36" (91.4 cm) 35
¹⁄₄" (89.5 cm)
42" (106.7 cm) 41
¹⁄₄"(105cm)
AWidth
110˚
90˚
23"
(58 cm)
max.
51"
(130 cm)
59"
(150 cm)
130˚
sledoM)mc7.601("24Single Door Models)mc4.19("63
110˚
90˚
110˚
90˚
42³⁄₄"
(108.6 cm)
44¹⁄₄"
(112.3 cm)
36" (91.4 cm) French Door Models
110˚
90˚
110˚
90˚
39³⁄₄"
(101 cm)
41"
(104 cm)
Page 1 of 2
■
The water line attached to the back of
the refrigerator is 5' (1.5 m) long.