Installation Guide
Tools Required:
Drill (optional)
Phillips
Screwdriver
Hacksaw
Tape Measure
Hammer
Step One
Trim Track to Fit Opening
(if necessary)
Cut the Top and Bottom
Track 1/16” (2mm) shorter
than the opening width with
a fine tooth hacksaw. Insert
the roll guides and fasten
the pivot brackets into the
track prior to installation of
the track. Install the pivot
brackets 1 7/8” (48mm)
from the wall as illustrated.
Step Three
Attach Top and
Bottom Track
Screw in tracks at a
minimum of ½“ (12mm),
in from the jamb face
(use long screws for the
top track and short
screws for the bottom
track). This will ensure
that the door does not
protrude from the
opening while it is
closed.
Step Two
Insert Pivots
Insert spring pivot into the
second hole at the top of the
pivot door. The bottom pivot,
used for height adjustment, must
be inserted into the second hole
at the bottom of the pivot door.
The remaining spring pivots are
inserted into the first holes of the
guide door.
Please Note: For Brass Laminate
bifold doors only, locate door with the
light scuff marks found at the
midpoint of the stiles. Orient this door
as pivot door. Affix door pull over
scuff marks (as per step 5).
Step Four
Install Doors
Insert the spring pivot on
the top of the pivot door
into the pivot bracket of
the top track. Then place
the bottom pivot into the
bracket of the bottom
track. Close the door so
that it is slightly ajar.
Depress the pivots in the
guide panel door and
snap the pins into the top
and bottom roll guides.
Note:
For heavier doors, you
may prefer to insert the
bottom pivot first.
Step Five
Final Adjustments
Both top and bottom pivot brackets can be
adjusted laterally. For lateral adjustment
release pivot bracket screw and slide pivot
bracket along track, once located, re-tighten
screw. Height adjustment is achieved by
lifting door slightly and turning the bottom
pivot with the aligner wrench as shown.
Attach the door pull onto the pivot door at
desired height (approx. 40” (1016mm) from
the floor). Clean the stile with isopropyl
(rubbing)alcohol before attaching the pull to
the door.
Trim snugger in 1/16” (2mm)
increments until door closes with a
light snap.
Height
Adjustment
Lateral
Adjustment
Pivot
Door
Snugger
Spring Pivot
Bottom Pivot
Guid
e
Doo
r
Pivot
Door
2nd Hole
1st Hole
Insertion of
roll guide
Insertion of pivot
bracket
½” (12mm)
Roll Guide
1 7/8”
(48mm)
Tracks must be
aligned and plumb
Four Door Application
P
i
v
o
t
D
o
o
r
G
u
i
d
e
D
o
o
r
G
u
i
d
e
D
o
o
r
P
i
vo
t
D
o
o
r
As per steps 1 - 5, pivot
brackets are installed
1-7/8” (48mm) from
each door jamb, and
roll guides are placed
at opposite end of the
pivot bracket as
illustrated. Place two
snuggers into top track.
Trim one snugger in
1/16” (2mm)
increments until doors
close with a light snap.
This Package Includes:
1 x Bifold Door
(2 panels)
2 x Track
(1 top, 1 bottom)
3 x Spring
Pivots
2 x Roll
Guides
2 x Pivot
Brackets &
Screws
1 x Door
Pull
1 x Snugger
1 x Bottom
Pivot
3 x Short
Screws(5/8”)
3 x Long
Screws(1½”)
Snuggers
Spring Pivots
Roll Guide
Bottom Pivot
Pivot Bracket
Snap pins into roll guide
using screwdriver
Spaced at 1 7/8
(48mm) from wall
Roll Guide
Spring Pivot
Spring Pivot
Pivot Bracket
Spring
Pivot
s
Bottom
Pivot
1 x Aligner
Wrench
Stiles
Rails
Door
Pull