Instruction Manual

ManualsBrandsKidztech Toys ManualsElectronicsR/C T-Rex

Table Of Contents

Fig. 3

Transmitter

Fig. 4

Dinoz

Light, Sound

& Smoking

Effect

Forward /

Turning

2.4 GHz

Signal Light

Transmitter - Battery Installation

Fig. 2

For Dinoz (Fig. 1 and Fig. 2)

1. Switch the power button to OFF position

2. Unscrew the battery cover

3. Open the battery cover

4. Install 4 new 1.5V”AA” batteries with correct polarities (+/-)

5. Close the battery cover

6. Tighten the screw on the battery cover

For Transmitter (Fig. 3 and Fig. 4)

1. Unscrew the battery cover

2. Open the battery cover

3. Install 2 new 1.5V “AA” batteries with correct polarities (+/-)

as shown inside the battery compartment

4. Close the battery cover

5. Tighten the screw on the battery cover

Fig. 5 Fig. 6

Fig. 7 Fig. 8

Fig. 1

2. Open the water tank cap on the Dinoz. (Fig.6)1. Please prepare a cup of clear tap water. Keep

squeezing and releasing the provided water

pump to fill up with the water. (Fig.5)

3. Squeeze the provided water pump to fill the

water tank into the Dinoz. (Fig.7)

4. Close the water tank cap firmly. (Fig.8)

87411

Contents

RC Dinoz x 1

Transmitter x 1

Water Pump x 1

Instruction Manual x 1

Battery Precaution

1. Alkaline batteries are recommend

2. Only batteries of the same or equivalent type as recommended are to be used

3. Do not mix alkaline, standard, or rechargeable batteries

4. Do not mix old and new batteries or different types of batteries

5. Non-rechargeable batteries are not to be charged

6. If rechargeable batteries are to be used, they are only to be charged under adult supervision

7. Rechargeable batteries are to be removed from the product before they are charged

8. Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions

9. Remove all batteries from the Dinoz and Transmitter when not in use

10. Exhausted batteries are to be removed from the product

11. The supply terminals are not to be short-circuited

12. Dispose of batteries properly / do not dispose the batteries in fire - it may cause them to explode or leak causing injury or damage

13. Battery installation and removal must only be done by an adult

Battery Requirement

1. RC Dinoz: 4 x 1.5V AA batteries

2. Transmitter: 2 x 1.5V AA batteries

Battery Installation

How to fill RC Dinoz with water for smoking effect

4 x AA

For Dinoz

(Included for try-me)

2 x AA

For Transmitter

(Not Included)

Dinoz

PRO. SYSTEM

age

TRY ME

OFF/ON

1.5V

Summary of content (4 pages)

PAGE 1
87411 3 age PRO. SYSTEM Contents Battery Requirement RC Dinoz x 1 Transmitter x 1 Water Pump x 1 Instruction Manual x 1 1. RC Dinoz: 4 x 1.5V AA batteries 2. Transmitter: 2 x 1.5V AA batteries 4 x AA For Dinoz (Included for try-me) 2 x AA For Transmitter (Not Included) Battery Precaution 1. Alkaline batteries are recommend 2. Only batteries of the same or equivalent type as recommended are to be used 3. Do not mix alkaline, standard, or rechargeable batteries 4.
PAGE 2
Trouble shooting for 2.4GHz pairing in case of no signal 1. Switch OFF the Dinoz and Switch ON to re-start. 2. Re-install batteries to the transmitter. 3. The transmitter signal light will flash for 7-8 seconds. 4. After the LED light of the transmitter stops flashing, the pairing process is complete for playing. 5. If pairing cannot be completed within 8 seconds, please turn off the Dinoz and re-start the pairing process. 6.
PAGE 3
87415 3 Instruction Manual 2.4G RADIO CONTROL T-REX PRO. SYSTEM Contents 15M / 49FT Range 3 x AA - RC T-Rex x 1 For T-Rex (Included for try-me) - RC Transmitter x 1 - Water Pump x 1 2 x AA - Instruction Manual x 1 RC Transmitter x 1 RC T-Rex x 1 Water Pump x 1 For Transmitter (Not Included) 1. Alkaline batteries are recommend 2. Only batteries of the same or equivalent type as recommended are to be used NO.: 84087 3. Do not mix alkaline, standard, or rechargeable batteries 4.
PAGE 4
87415 Trouble shooting for 2.4GHz pairing in case of no signal 1. Switch OFF the T-Rex and Switch ON to re-start. 2. Re-install batteries to the transmitter. 3. The transmitter signal light will flash for 7-8 seconds. 4. After the LED light of the transmitter stops flashing, the pairing process is complete for playing. 5. If pairing cannot be completed within 8 seconds, please turn off the T-Rex and re-start the pairing process. 6.