Installation Manual
1) Pass threaded stud at end of one corner rod through hole in
one corner of bottom ring.
2) Thread finial onto threaded stud protruding from bottom
ring. Tighten finial to secure rod in place. NOTE: Sides of rod
should be square with sides of bottom ring.
3) Repeat steps 1 and 2 for remaining corner rods.
4) Place top ring on top of corner rods. Pass holes in in top
ring over threaded studs on top of corner rods.
5) Lower arm down onto top ring.
6) Pass hole in tab on bottom of arm over threaded stud
protruding up from top ring.
7) Thread finial onto threaded stud.
8) Repeat steps 5-7 for remaining arms.
9) Pass wire from fixture body through center stem.
10) Screw center stem into hole in top of fixture body.
11) Lower bottom half of sphere over center stem. Pass hole in
bottom half sphere over top of center stem.
12) Lower end of threaded pipe with hexnut into bottom half of
sphere.
13) Screw end of threaded pipe into end of center pipe inside
bottom half of sphere.
14) Align hole in top of one arm with one hole in bottom half of
sphere.
15) Thread ball stud into hole in arm and into bottom half of
sphere. Tighten ball stud to secure arm in place.
16) Repeat steps 14 and 15 for remaining arms.
17) Lower top half of sphere down onto bottom half of sphere.
18) Pass hole in top half of sphere over end of threaded pipe
protruding from inside of bottom half of sphere.
19) Pass hole in small top trim over end of threaded pipe
protruding from top of sphere. Set top trim on top of sphere.
20) Thread loop onto threaded pipe.
21) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
22) Take threaded pipe from parts bag and screw in screw collar
loop a minimum of 6 mm (1/4”). Lock into place with hexnut.
23) Run another hexnut down threaded pipe almost touching
first hexnut. Now screw threaded pipe into mounting strap.
Mounting strap must be positioned with extruded thread
faced into outlet box. Threaded pipe must protrude out the
back of mounting strap. Screw third hexnut onto end of
threaded pipe protruding from back of mounting strap.
24) Connect mounting strap to outlet box.
25) Unscrew the threaded ring from screw collar loop. Take
canopy and pass over screw collar loop. Approximately one
half of the screw collar loop exterior threads should be
exposed. Adjust screw collar loop by turning assembly up or
down in mounting strap. Remove canopy.
26) After desired position is found, tighten both top and bottom
hexnuts up against the bottom and top of the mounting
strap.
27) Slip canopy over screw collar loop and thread on threaded
ring. Attach chain (with fixture connected) to bottom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down.
28) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. Pass wire through threaded ring,
canopy, screw collar loop, threaded pipe and into outlet box.
29) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
20.00 [508.0]
MOUNTING STRAP
ABRAZADERA DE MONTAJE
HEXNUT
TUERCA
HEXAGONAL
THREADED PIPE
TUBO ROSCADO
CANOPY
ESCUDETE
THREADED RING
ANILLO ROSCADO
Date Issued: 3/8/13 IS-42568-US
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
LOOP
ANILLO
SCREW COLLAR LOOP
OJAL DE COLLAR
ROSCADO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
30) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
31) Raise canopy to ceiling.
32) Secure canopy in place by tightening threaded ring onto
screw collar loop.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
THREADED PIPE
TUBO ROSCADO
HEXNUT
TUERCA
HEXAGONAL
ARM
BRAZO
FINIAL
CAPUCHÓN
SMALL TOP TRIM
PEQUEÑA MOLDURA
SUPERIOR
TOP HALF OF SPHERE
PARTE SUPERIOR DE LA MITAD
BOTTOM HALF OF
SPHERE
MITAD INFERIOR DE
LA ESFERA
FINIAL
CAPUCHÓN
BALL STUD
ESPÁRRAGO DE
CABEZA ESFÉRICA
CENTER STEM
VÁSTAGO DEL
CENTRO
FIXTURE BODY
CUERPO DEL
ARTEFACTO
TOP RING
ANILLO SUPERIOR
CORNER ROD
VARILLA DE ESQUINA
BOTTOM RING
ANILLO DEL FONDO
TAB
LENGÜETA