0ALLA 4- $ESIGNED TO COORDINATE WITH A POPULAR +ICHLER ,IGHTING COLLECTION )NCLUDES OUR NEW #OOL4OUCH #ONTROL 3YSTEM 4- ,OOKS PERMANENT BUT GOES WHEREVER YOU GO 5 3 0ATENT 0ENDING +ICHLER ,IGHTING %AST 0LEASANT 6ALLEY 2OAD 0 / "OX #LEVELAND /HIO #USTOMER 3ERVICE !- TO 0- %34 -ONDAY &RIDAY KHA9090114 )NSTRUCTION -ANUAL
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 10. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. 3.
Palla TM 2 2. TOOLS AND MATERIALS REQUIRED Philips screw driver Slot screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: a. b. c. d. e. f. g. h. i. j. k. l. m. n. o. p. q.
3 4. MOUNTING OPTIONS If there isn't an exsiting UL (cUL for Canadian Installation) listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Fig. 1 Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes.
0ALLA 4- (!.').' 4(% &!.
2ETAINING #LIP $OWNROD -OTOR #OUPLING 7ASHER 3ET SCREW (ITCH 0IN 3TEP ,OOSEN THE TWO SET SCREWS AND REMOVE THE HITCH PIN AND RETAINING CLIP FROM THE COUPLING ON TOP OF THE MOTOR ASSEMBLY #AREFULLY FEED THE ELECTRICAL LEAD WIRES FROM THE FAN UP THROUGH THE DOWNROD 4HREAD THE DOWNROD INTO THE COUPLING UNTIL THE HITCH PIN HOLES ARE ALIGNED 2EPLACE THE HITCH PIN AND RETAINING CLIP 4IGHTEN BOTH SET SCREWS &IG 3TEP 3LIP THE COUPLER COVER DECORATIVE ROD DECORATIVE RING CANOPY COVER AND CEILING
Palla TM 6. INSTALLATION OF SAFETY SUPPORT (for Canadian Installation ONLY) A safety support cable is provided to help prevent the ceiling fan from falling, please install it as follows. Ceiling mounting bracket Attach safety cable to ceiling joist with screw and washer Step 1. Attach the provided wood screw and washer to the ceiling joist next to the mounting bracket but do not tighten. (Fig. 12) Step 2.
7 Outlet Box Black (AC in L) Green (Ground) White (AC in N) Secure each set of wire connections with the plastic wire nuts provided in the parts bag. Receiver Black (TO MOTOR L) White (TO MOTOR N) Green (Ground) Blue (For Bottom Light) Orange (For Upper Light) Decorative rod Step 3. Receiver to Supply Wires Electrical Connections: (Fig. 14) Connect the black (load) wire from the ceiling outlet box to the black wire marked "AC in L" on the receiver.
0ALLA !33%-",9).' !.$ !44!#().' 4(% &!.
9 11. INSTALLING THE BATTERIES Remove the battery compartment cover on the back of the CoolTouch™ Transmitter and insert both batteries provided. Make sure the + sign is facing up. Take care during this procedure NOT TO move the frequency dip switches inside this compartment. The settings MUST remain the same as the settings on the receiver for proper communication with the control system. It's a good idea to remove these batteries if your fan is not used for extend periods of time, (months). Fig. 20 12.
Palla Speed settings for warm or cool weather depend on factors such as the room size. Ceiling height, number of fans and so on. Warm Weather Operation: Forward (counter clockwise) A downward airflow creates a cooling effect as shown in Fig. 22. This allows you to set your air conditioner on a warmer setting without affecting your general comfort. Cool Weather Operation: Reverse (clockwise). An upward airflow moves warm air off the ceiling areas as shown in Fig. 23.
11 13. INSTALLING THE COOLTOUCH™ CONTROL SYSTEM WALL PLATE Outlet box Switch Wall plate Fig. 24 Outlet box Metal plate CoolTouch™ wall plate Screws Plastic plugs Screws Fig. 25 Select a location to install your CoolTouch™ Control System Transmitter. You can replace an existing wall switch or, install the transmitter on ANY flat surface. Option 1: Install the control system using an existing wall switch outlet box. Make sure the electrical power is TURNED OFF at the main panel before continuing.
Palla TM 12 15. TROUBLE SHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. 3. Make sure the batteries are installed properly. Positive (+) side facing out. 4. Check to make sure the batteries are not dead. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2.